Atlona AT-HD50SS User Manual
Hdmi v1.3 over single cat5e/6 distribution series
Hide thumbs
Also See for AT-HD50SS:
- Specifications (2 pages) ,
- User manual (14 pages) ,
- User manual (11 pages)
Related Manuals for Atlona AT-HD50SS
Summary of Contents for Atlona AT-HD50SS
- Page 1 AtlonA ™ HDMI v1.3 over Single CAT5E/6 Distribution Series User’s Manual AT-HD50SS AT-HD50RSL AT-HDRS AT-HD15SRS Rev.1007...
-
Page 2: Table Of Contents
............... 2 3. Package Contents ............... 4. Specifications ............... 5. Panel Descriptions ............... 5.1 Sender Unit AT-HD50SS .............. 5.2 Sender / Receiver Unit AT-HD50RSL ..........5.3 Receiver Unit AT-HDRS .............. 5.4 Receiver Unit AT-HD15SRS ............6. Installation ............... -
Page 3: Introduction
The devices are cascadable, allowing you to extend HDMI/DVI compliant displays almost anywhere. Note: The AT-HD50SS is only a sender/transmitter unit and requires a receiver unit to work. Compatible receives are: AT-HDRS (CAT5/6 in and HDMI out) or AT-HD50RSL (Cat5/6 input,... -
Page 4: Features
Allows cascading Compatible with different receiver options: AT-HDRS and AT-HD50RSL Note: Atlona recommends to use Cat6 or Cat5e cables for better performance. Atlona recommends to always use "Type B" termination for the Cat6 or Cat5 Cables to extend the distance. -
Page 5: Specifications
SPECIFICATIONS Model Name AT-HD50SS AT-HD50RSL Technical Role of usage Sender (TX) Sender / Receiver (TRX) HDMI compliance HDMI 1.3c HDCP compliance Video bandwidth Single-link 225MHz (6.75Gbps) Video support 480i / 480p / 720p / 1080i / 1080p60 24/30/36-bit color Full HD (1080p) 40m (130ft) [CAT5e] / 50m (165ft) [CAT6]... - Page 6 Model Name AT-HDRS AT-HD15SRS Technical Role of usage Receiver (long range RX) Receiver (short range RX) HDMI compliance HDMI 1.3c HDCP compliance Video bandwidth Single-link 225MHz (6.75Gbps) Video support 480i / 480p / 720p / 1080i / 1080p60 24/30/36-bit color Full HD (1080p) —...
-
Page 7: Panel Descriptions
6. HDMI OUT: Local HDMI for connecting to a HDMI display with a HDMI male-male cable, or cascade to the HDMI IN of another AT-HD50SS, AT-HD14SS, or AT-HD19SS, or link to a remote display with AT-HDRS or AT-HD15SRS via a Cat.5e/6 cable 7. - Page 8 B. Connect the display which you want to read EDID to HDMI OUT port on the AT-HD50SS. C. Set DIP pin-1 at ON (). D. Power on the AT-HD50SS and wait up to 20 seconds. The green LED will dim and light to indicate the EDID learning process is complete.
-
Page 9: Sender/Receiver Unit At-Hd50Rsl
7-to-0 or from F-to-8 to find the optimal visual experience. 4. HDMI Signal IN: Link to AT-HD14SS, AT-HD19SS, AT-HD50SS, AT-HD50RSL, or AT-HD- V40SS with a Cat-5/5e/6 cable. 5. Audio OUT: Plug in a local speaker 6. -
Page 10: Receiver Unit At-Hdrs
Receiver Unit AT-HDRS Input Panel +5V DC: Connect to 5V DC power supply unit. HDMI Signal IN: Connect to the HDMI Signal OUT on the sender unit AT-HD50SS or AT-HD50RSL with a solid Cat-5/5e/6 UTP/STP cable. Output Panel Signal Level: Adjust the 8-level signal equalization control to the received HDMI signals. The HDMI signal level varies from 0 (strongest) to 7 (weakest) for respective transmission length from longest possible range to short distance. -
Page 11: Installation
Extends HDMI signals to next cascading device with one local display 1. Switch off all devices, including monitors. 2. Connect a local HDMI display to the HDMI out of the AT-HD50SS and then connect a speaker to the 3.5mm audio socket. - Page 12 Diagram:...
-
Page 13: Notice
NOTICE 1. When adjusting the signal level on the receiver unit, dial the rotary control switch from 7 to 0 and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level setting may cause overpowering issues that would shorten the product’s life significantly! 2. -
Page 14: Safety Information
If the wall plug does not fit into your local power socket, hire an electrician to replace Use only accessories recommended by ATLONA your obsolete socket. to avoid fire, shock or other hazards. Do not modify the wall plug. -
Page 15: Warranty
Atlona Technologies and its suppliers’ entire liability and Customer’s exclusive remedy shall be, at Atlona Technologies’ option, either return of the price paid for the Product, or repair or replacement of the Product that does not meet this Limited Warranty and which is returned to Atlona Technologies with a copy of Customer’s receipt. -
Page 16: Atlona Product Registration
At Atlona, we respect and protect your privacy and assure you that your registration information is completely secure. Of course, Atlona product registration is totally voluntary and failure to register will not diminish your limited warranty rights.
Need help?
Do you have a question about the AT-HD50SS and is the answer not in the manual?
Questions and answers