Aussie BONDI II DELUXE Assembly And Use Manual

Aussie BONDI II DELUXE Assembly And Use Manual

Lp gas grill

Advertisement

Aussie
LP Gas Grill
Assembly and Use Manual
For Customer Service, call 1-800-251-7558
•READ AND FOLLOW INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY OR USE. FAILURE TO
FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, SERIOUS BODILY INJURY AND/OR
!
PROPERTY LOSS.
•FOR HOUSEHOLD OUTDOOR USE ONLY. NOT FOR COMMERCIAL USE.
•SOME PARTS MAY CONTAIN SHARP EDGES-ESPECIALLY WHERE NOTED IN THIS MANUAL!
WEAR PROTECTIVE GLOVES IF NECESSARY.
•THESE INSTRUCTIONS MUST BE KEPT WITH THE CONSUMER AND RETAINED FOR FUTURE USE.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your gas
supplier or your fire department.
II
TM
Deluxe
TM
TM
FOR YOUR SAFETY
1. Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
II
TM
Elite

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BONDI II DELUXE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Aussie BONDI II DELUXE

  • Page 1 Aussie LP Gas Grill Assembly and Use Manual Deluxe Elite For Customer Service, call 1-800-251-7558 •READ AND FOLLOW INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY OR USE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, SERIOUS BODILY INJURY AND/OR PROPERTY LOSS. •FOR HOUSEHOLD OUTDOOR USE ONLY. NOT FOR COMMERCIAL USE.
  • Page 2: Table Of Contents

    In addition, the combustion products 6. Have an ABC fire extinguisher accessible. of such fuels, including liquefied petroleum Never attempt to extinguish a grease fire with (LP), contain chemicals known to the state of water or other liquids. © Aussie Grill Company 2001...
  • Page 3 DANGER! If you see, smell, or hear the hiss of WARNING! If your grill catches on fire: escaping gas from the LP cylinder: • If the fire is in the grill portion and you can safely A. Get away from the cylinder. reach the control knobs, then turn them off by turning B.
  • Page 4 — NOTICE — AUSSIE GRILL COMPANY STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE INADVERTENTLY OMITTED ANY PARTS NEEDED FOR ASSEMBLY, OR YOU NEED TROUBLESHOOTING INFORMATION, PLEASE CONTACT US USING OUR TOLL FREE NUMBER. THANK YOU FOR PURCHASING AN AUSSIE GRILL COMPANY PRODUCT.
  • Page 5: Parts Diagram

    Parts Diagram - Some small parts may not be depicted...
  • Page 6: Parts List

    ASSEMBLY INSTRUCTIONS for BONDI II DELUXE & BONDI II ELITE MODELS PREPARATION FOR ASSEMBLY: Removing parts from carton and some assembly will require two people. Before starting assembly, read the instructions and your manual. This manual covers several Bondi Grill models. Use only the steps that pertain to your model. Remove all the parts from the carton and lay them on a smooth, clean surface.
  • Page 7 BONDI II BONDI II PART/ DESCRIPTION Part# DELUXE ELITE Right Side Table 03.6170.00 w/Perforations Privacy Panel 03.6172.00 Flavor Activator 03.6250.00 Warming Rack 03.6253.00 Cooking Grid, Porcelain 03.6255.00 Hood Shield 03.6289.00 Left Side Table with Side 03.6171.00 Burner 21 Screw, M5 X 35 03.4099.00 Washer M6 03.4095.00...
  • Page 8: Step 1- Cart Assembly

    TOOLS: STEP 1- Cart Assembly ITEM 21 M5 X 35 SCREW 8 pcs Actual Size Velcro Patches ITEM 4 ITEM 6 Bottom Shelf ITEM 3 •Using eight M5 X 35 screws, attach the Legs to the Bottom Shelf as ITEM 2 ITEM 1 shown.
  • Page 9: Step 3 - Mount Body Onto Cart

    Step 3 - Mount Body onto Cart It may be necessary to stand grill up after the legs start together and press firmly into final position. Secure using 4 M6X35 screws & nuts. Lay Cart and Body on its backside. Align Cart legs with Body legs and press together until screw holes align.
  • Page 10: Step 5 - Mount Rear Brace

    Step 5 - Mount Rear Brace Step 4 Continued - Mount SIde Tables Item 10 Rear Brace 1 pc Elite Model Only: Side Burner Table Item 27 Screw, M6X70 2pcs Actual Size Mount Rear Brace (Item 10) to rear legs using 2 M6X70 Screws through lower holes on rear Side Table mount.
  • Page 11: Step 8 - Attach Privacy Panel

    Step 8 - Attach Privacy Panel (ITEM 15 ) PRIVACY PANEL 1 pc •Attach Privacy Panel to the velcro patches on back side of front legs as shown. Note: Privacy Panel may be removed to install LP Cylinder then reattached. Step 9 - Insert Cooking Grid (ITEM 18) Porcelain Cooking Grid...
  • Page 12: Step 10 - Attach Lp Cylinder

    Step 10 - Attach LP Cylinder •Swing the Cylinder Retainer Clip to outside of the Bottom Shelf. Place the LP Cylinder in circular hole on Bottom Shelf. The cylinder should be turned slightly as shown below to allow the Regulator Hose to reach.
  • Page 13: Step 11 - Leak Test

    Step 11 - Leak Test •Before using your grill a leak test must be performed on the Control Valves, Burner manifold, and Regulator/ Hose connections. Supplies Needed for a Leak Test Clean paint brush, water, and dishwashing liquid. How to perform a leak test WARNING! Never use an open flame to test for gas leaks.
  • Page 14: Operating And Maintaining Your Lp Gas Grill

    Gas Cylinder to Grill · Do not operate the LP gas grill when the LP gas cylinder · The LP gas cylinder, for use with the Aussie LP gas grills, is not attached to the cart as shown in the Assembly must meet the following requirements: 1) 12”...
  • Page 15: B) Before Using Your Grill

    · Never connect or disconnect LP gas cylinder or fittings Precautions while grill is in use or is hot. · When the LP gas cylinder is connected, the grill must be kept outside in a well-ventilated space. Turn off all of the grill control knobs and the LP cylinder valve ·...
  • Page 16: Leak Testing

    Leak Testing OPERATING THE LP GAS GRILL · Always perform a leak test before each use. · Leak test must be performed in a well ventilated area. · Before proceeding, make certain that you · Never perform a leak test on a grill while in use or understand the Important Safeguards on pages 2 hot.
  • Page 17: Preparation Before Cooking

    Preparation Before Cooking 3) From the “Off” position, push control knob in on the left · Wash the porcelain or chrome coated Cooking Grids side and turn counter-clockwise to the high position. with a mixture of hot water and baking soda. 4) Push the igniter button several times so that it clicks each ·...
  • Page 18: Lighting The Side Burner

    Lighting the Side Burner (Elite Series Only) WARNING: If burner fails to light after following Steps 2 & 3, turn Side Burner Knob to the “off” How to light your LP Gas Grill Side Burner (See position and close the valve on the LP gas cylinder. diagram below for illustrations) Wait five minutes;...
  • Page 19: Manual Lighting Of The Grill

    Manual Lighting of the Grill 4) Push in and turn the right main burner control knob counter- clockwise to the “high” position. WARNING: If the burner fails to ignite after · Open Hood before lighting the grill to prevent an following the above procedure, turn control knob to explosion from gas build-up.
  • Page 20: Check Your Flame

    Check Your Flame End of Cooking Session Your burner has been preset by the manufacturer for opti- mal flame performance. A blue flame, possibly with a small yellow tip, is the result of the optimal air and LP gas mix- ·...
  • Page 21: Porcelain Coated Cooking Surfaces

    Burner Maintenance CARE AND MAINTENANCE Regularly clean your LP gas grill between uses and espe- cially after extended periods of storage. Ensure the grill · Check the LP gas grill for gas leaks and Burner and its components are cool before cleaning. In order to obstructions before each use.
  • Page 22: Flavor Activator

    Flavor Activator™ Remove and wash the Flavor Activator™ in order to keep it clean. Burning off the residue after each cooking will make · Always turn off the LP gas cylinder at the LP cleaning easier. Clean with soap and water. cylinder valve when not in use.
  • Page 23: Troubleshooting

    TROUBLESHOOTING Solution Possible Cause Problem Burner will not light Burner is not connected to Insure BurnerTube is on the end of Valve using the ignitor Valve. Not pausing long enough When lighting the Burner, push-in and turn control panel knob before clicking the Igniter counter-clockwise to the high position.
  • Page 24 TROUBLESHOOTING Problem Possible Cause Solution High or gusting winds Flames blow out Turn front of grill to face wind or increase flame height. Check LP gas cylinder. Refill if necessary. Gas in LP cylinder is low Excess flow valve tripped See “Low flame”...
  • Page 25: Important Notice - Lp Cylinder With Opd

    OPD. Otherwise you will lose the OPD (Overfill Prevention Device) feature. If there is not an LP cylinder available for exchange equipped with an OPD, we recommend that you have your cylinder filled at an authorized LP gas dealer by a qualified attendant. © AUSSIE™ GRILL COMPANY...
  • Page 26: Limited Warranty

    Burner and Cooking Grid are warranted for a period of one (1) year from the date of purchase. All other parts are warranted for a period of one (1) year from the date of purchase. Aussie Grill Company DOES NOT warrant in any way the propane cylinder (see label on cylinder for cylinder manu- facturer’s warranty.) The LP cylinder manufacturer is responsible for the materials, workmanship and...

This manual is also suitable for:

Bondi ii elite

Table of Contents