Related Manuals for Advantech ASMB-784
Summary of Contents for Advantech ASMB-784
- Page 1 User Manual ASMB-784 LGA 1150 Intel® Xeon® E3 V3 ATX Server Board with 2 PCIe x16 slots (x8 link) or 1 PCIe x16 slot (x16 link), 3 PCI, USB 3.0, PCIe Gen III, Quad/Dual LANs...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
- Page 3 Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
-
Page 4: Declaration Of Conformity
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer's instructions. ASMB-784 User Manual... - Page 5 96D3-8G1333E-TR 1333 AQ56M72E8BJH9S 1333 AQ12M72E8BKH9S 96D3-4G1333E-AT 1333 AQ24M72E8BLH9S 96D3-8G1333E-AT Transcend 1600 TS1GLK72V6H ASMB-784 Ordering Information Part Number Chipset Memory LAN IPMI Optional Module ASMB-784G2-00A1E C226 DDR3 ECC UNB/Non-ECC 2 (IPMI-1000) Optional Module ASMB-784G4-00A1E C226 DDR3 ECC UNB/Non-ECC 4 (IPMI-1000) ASMB-784 User Manual...
-
Page 6: Initial Inspection
It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the ASMB-784, check it for signs of ship- ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately. -
Page 7: Table Of Contents
Board Layout: Jumper and Connector Locations........6 Figure 1.1 Jumper and Connector Locations....... 6 Figure 1.2 I/O connectors ............6 ASMB-784 Block Diagram ................ 7 Figure 1.3 ASMB-784 Block Diagram.......... 7 Safety Precautions ..................7 Jumper Settings ..................8 1.8.1 How to set jumpers ............... - Page 8 Auxiliary 8-pin power connector (ATX12V1) ........... 24 2.19 SPI Flash Connector(SPI_CN1) ............. 25 2.20 Low Pin Count Connector (LPC1)............25 Table 2.3: Advantech LPC Module List ........25 2.21 PCI Clock Selection (JPCICLK1) ............26 2.22 KBMS Power Selection (JKBMS1) ............26...
- Page 9 Windows OS Driver Setup ..............72 Chapter Configuration......73 Introduction ..................... 74 Features ....................74 Installation ....................74 Windows OS Driver Setup (LAN) ............74 Chapter Intel ME ..........75 Introduction ..................... 76 Installation ....................76 Chapter Intel USB 3.0........77 Introduction ..................... 78 ASMB-784 User Manual...
- Page 10 Table B.19:SPI_CN1:SPI fresh card pin connector ....97 B.19 SMBUS1: Connector of SMBUS from PCH ..........97 Table B.20:SMBUS Connector ........... 97 B.20 System I/O Ports..................97 Table B.21:System I/O ports............97 B.21 Interrupt Assignments ................98 ASMB-784 User Manual...
- Page 11 Table B.22:Interrupt assignments ..........98 B.22 1st MB Memory Map ................98 Table B.23:1st MB memory map ..........98 ASMB-784 User Manual...
- Page 12 ASMB-784 User Manual...
-
Page 13: Chapter 1 Hardware Configuration
Chapter Hardware Configuration... -
Page 14: Introduction
PCIe x16 slots with x8 link(Gen III) from CPU, and two PCIe x1 slot (Gen II) from PCH. In addition, ASMB-784 also comes with three PCI slots via a discrete PCIe to PCI bridge chip to support legacy PCI expansion cards and has four or two Gigabit Ethernet LAN via dedicated PCIe bus, which offers bandwidth up to 300 MB/s eliminating network bottlenecks. -
Page 15: Specifications
USB port: Supports up to 4 USB 3.0 ports with transmission up to 5Gbps and 9 USB 2.0 ports with transmission rates up to 480 Mbps. LPC: One LPC connector to support Advantech TPM LPC modules. GPIO: ASMB-784 supports 8-bit GPIO from super I/O for general purpose con- trol application. 1.3.4 Graphics ... -
Page 16: Industrial Features
Board weight: 0.8 kg (weight of board) Jumpers and Connectors Connectors on the ASMB-784 motherboard link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers that are used to configure your system for your application. - Page 17 Audio front panel header LPT1 Parallel port COM2 Serial port: RS-232 JFP1~3 Front panel header LPC1 Low pin count connector for Advantech TPM LPC modules LANLED1, LANLED2 LED extension connector VOLT1 Voltage Display PMBUS1 PMBUS connector to communicate with power supply SGPIO1...
-
Page 18: Board Layout: Jumper And Connector Locations
JFP3 CPUFAN0 CPUFAN0 JFP1~2 CPUFAN_SEL1 USB 12 SPI_CN1 JME1 SYSFAN_SEL1 JCMOS1 JCASEOP SW1 JCASEOP_SW1 JCASE1 SMBUS1 SYSFAN1 SYSFAN0 GPIO1 JWDT1 SATAIII SYSFAN2 PSON1 VOLT1 SGPIO1 Figure 1.1 Jumper and Connector Locations ASMB-784G2-00A1E ASMB-784G4-00A1E Figure 1.2 I/O connectors ASMB-784 User Manual... -
Page 19: Asmb-784 Block Diagram
Nuvoton BIOS Flash NCT6776 1 LPT Figure 1.3 ASMB-784 Block Diagram Safety Precautions Warning! Always completely disconnect the power cord from your chassis when- ever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sud- den power surges. -
Page 20: Jumper Settings
1.8.1.1 CMOS and ME clear (JCMOS1) The ASMB-784 motherboard contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins 1-2 closed. If you want to reset the CMOS data, set JCMOS1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed. - Page 21 The ASMB-784 contains a watchdog timer that will reset the CPU. This feature means the ASMB-784 will recover from a software failure or an EMI problem. The JWDT1 jumper settings control the outcome of what the computer will do in the event the watchdog timer is tripped.
-
Page 22: System Memory
1.8.1.5 CPU,SYSTEM fan PWM/DC mode selection(CPUFAN_SEL1, SYSFAN_SEL1) The ASMB-784 contains a jumper that can support PWM or DC mode, Normally this jumper should be set with pin 1-2 closed. If you want to change to DC mode, set CPUFAN_SEL1, SYSFAN_SEL1 to 2-3 closed for disable. -
Page 23: Memory Installation Procedures
1.11 Cache Memory The ASMB-784 supports a CPU with one of the following built-in full speed L3 caches: The built-in third-level cache in the processor yields much higher performance than conventional external cache memories. - Page 24 ASMB-784 User Manual...
-
Page 25: Chapter 2 Connecting Peripherals
Chapter Connecting Peripherals... -
Page 26: Introduction
Parallel Port (LPT1) LPT1 The parallel port is normally used to connect the motherboard to a printer. The ASMB-784 includes an onboard parallel port, accessed through a 25-pin flat-cable connector, LPT1. ASMB-784 User Manual... -
Page 27: Usb Ports
(LAN1_USB4_5,LAN2_USB0_1,USB2_3, USB6_7, USB8_9,USB10_11, USB12) ASMB-784 provides up 13 USB ports. USB4~12 are USB 2.0 ports supporting trans- mission rates up to 480 Mbps, and USB0~3 are USB 3.0 ports supporting transmis- sion rate up to 5Gbps.These ports support Plug & Play and hot swapping for up to 127 external devices and are able to be disabled in BIOS menu. -
Page 28: Usb Power Switch
USB10_11, USB12 JUSB2 ASMB-784 allows user to set USB power between +5VSB and +5V. When the jumper is set as +5V, the board doesn't support S3/S4. Note! When USB power is switched to +5V, it can't be connected with pow- ered USB KVM. -
Page 29: Vga Connector (Vga1)
COM1 COM2 The ASMB-784 offers two serial ports (one on the rear panel and one onboard).These ports can connect to a serial mouse, printer or communications net- work. The IRQ and address ranges for those ports are fixed. However, if you want to disable the port or change these parameters later, you can do this in the system BIOS setup. -
Page 30: Ps/2 Keyboard And Mouse Connector (Kbms1) And External Keyboard & Mouse (Kbms2)
This gives system inte- grators greater flexibility in designing their systems. CPU Fan Connector (CPUFAN0) CPUFAN0 CPUFAN0 If a fan is used, this connector supports cooling fans that draw up to 500 mA (6 W). ASMB-784 User Manual... -
Page 31: System Fan Connector (Sysfan0, Sysfan1, Sysfan2 And Sysfan3)
SYSFAN0 SYSFAN1 If a fan is used, this connector supports cooling fans that draw up to 1A (12W). 2.10 Front Panel Connectors (JFP1~3) There are several external switches and LEDs to monitor and control the ASMB-784. PWRSW RESET JFP1 SNMP... -
Page 32: Power Led (Jfp3)
System Off in deep sleep 2.10.2 External Speaker (JFP2 pins 1, 4, 7, 10) JFP2 pins 1, 4, 7, 10 connector for an external speaker. The ASMB-784 provides an onboard buzzer as an alternative. To enable the buzzer, set pins 7-10 as closed. 2.10.3 HDD LED Connector (JFP1 pins 2 &... -
Page 33: 8-Pin Alarm Board Connector (Volt1)
2.11 8-pin Alarm Board Connector (VOLT1) VOLT1 VOLT1 connects to the alarm board of Advantech chassis. These alarm boards give warnings if a power supply or fan fails, if the chassis overheats. 2.12 Case Open Connector (JCASE1) JCASE1 JCASE1 is for chassis with a case open sensor. The buzzer on the motherboard sounds if the case is opened. -
Page 34: Front Panel Lan Indicator Connector (Lanled1)
LAN2/4_LED1_ACT VCC3_LAN1/3LED VCC3_LAN2/4LED LAN1/3_LED1_1000M LAN2/4_LED2_1000M LAN1/3_LED2_100M LAN2/4_LED0_100M VCC3 LANLED2 LANLED1 2.14 Serial ATA Interface (SATA0~5) 0 2 4 1 3 5 SATAIII ASMB-784 features six high performance serial ATA III interfaces (up to 600 MB/s, blue connector). ASMB-784 User Manual... -
Page 35: Pci Slots (Pci_Slot1, Pci_Slot3, Pci_Slot5)
PCI Slots (PCI_SLOT1, PCI_SLOT3, PCI_SLOT5) PCI_SLOT1 PCI_SLOT3 PCI_SLOT5 There are three 32bit PCI slots designed on ASMB-784, and default clock is 33 Mhz. PCI clock could be selected between 33 or 66 MHz by JPCICLK1 jumper, and please refer section of 2.21. 2.16... -
Page 36: Pcie X1 Expansion Slot (Pciex1_Slot2, Pciex1_Slot7)
For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version). Do not forget to con- nect the 8-pin EATX12 V power plug; otherwise, the system will not boot. ATX12V1 ASMB-784 User Manual... -
Page 37: Spi Flash Connector(Spi_Cn1)
2.19 SPI Flash Connector(SPI_CN1) SPI flash card pin header which can flash BIOS while ASMB-784 can not be power on and ensures platform integrity. SPI_CN1 2.20 Low Pin Count Connector (LPC1) LPC1 LPC connector on AIMB-784 is reserved for Advantech LPC modules. -
Page 38: Pci Clock Selection (Jpciclk1)
+5VSB for KBMS 2-3 Closed +5V for KBMS ASMB-784 allows user to set keyboard and mouse power between +5VSB and +5V. When the jumper is set as +5V, the board doesn't support S3/S4. Note! When KBMS power is switched to +5V, it can't be connected with pow- ered PS/2 KVM. -
Page 39: Bios Operation
Chapter BIOS Operation... -
Page 40: Introduction
The Setup program uses a number of menus for making changes and turning the special features on or off. This chapter describes the basic navigation of the ASMB-784 setup screens. Figure 3.1 Main setup screen AMI’s BIOS ROM has a built-in Setup program that allows users to modify the basic... -
Page 41: Main Menu
Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format. ASMB-784 User Manual... -
Page 42: Advanced Bios Features Setup
Advanced BIOS Features Setup Select the Advanced tab from the ASMB-784 setup screen to enter the Advanced BIOS setup screen. You can select any of the items in the left frame of the screen, such as CPU configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>... -
Page 43: Pci Subsystem Settings
Figure 3.4 PCI subsystem settings screen PCI Latency Timer Value in units of PCI clocks for PCI device latency timer register. VGA Palette Snoop This item is designed to solve problems caused by some non-standard VGA cards. Figure 3.5 PCI Express Setting ASMB-784 User Manual... - Page 44 On non-PCIe aware OS (pre Windows Vista) some devices may not be correctly re initialized after S3. Enabling this restores PCIe device configurations on S3 resume. When enabling this item, it may cause issues with other hardware after S3 resume. ASMB-784 User Manual...
-
Page 45: Acpi Settings
"Enable” or “disable" Hibernation. ACPI Sleep State Specifies the ACPI sleep state when the system enters suspend. Lock Legacy Resources "Enable" or "Disable" Lock Legacy Resources. S3 Video Repost This item is to enabled or disabled S3 video repost. ASMB-784 User Manual... -
Page 46: Trusted Computing
3.3.3 Trusted Computing Figure 3.7 TPM Settings Security Device Support “Enable” or “disable” TPM Support. You can purchase Advantech LPC TPM module to enable TPM function. P/N: PCA-TPM-00A1E ASMB-784 User Manual... -
Page 47: Cpu Configuration
Hardware Prefetcher is a technique that fetches instructions and/or data from mem- ory into the CPU cache memory well before the CPU needs it, so that it can improve the load-to-use latency. You may choose to enable or disable it. ASMB-784 User Manual... - Page 48 This item is to enable or disable package C state limit. Intel TXT(LT) Support This item is to enable or disable Intel TXT(LT) support. ACPI T State This item is to enable or disable ACPI T state support. ASMB-784 User Manual...
-
Page 49: Sata Configuration
To identify the SATA is connected to Solid State Drive or Hard Disk Drive. Port 0~5 Spin Up Device On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device. ASMB-784 User Manual... -
Page 50: Pch-Fw Configuration
3.3.6 PCH-FW Configuration Figure 3.10 Intel ME FW Configuration Information This page shows the Intel ME configuration ASMB-784 User Manual... -
Page 51: Amt Configuration
Set ME to Soft temporary disable. Enable or disable Alert Specification format. Activate Remote Assistance Process To trigger CIRA boot. USB Configure To enable or disable USB configure function. PET Progress Enable or disable PET event progress to receive PET events. ASMB-784 User Manual... -
Page 52: Usb Configuration
Allows you to select the USB transfer time-out value. [1,5,10,20sec] Device reset time-out Allows you to select the USB device reset time-out value. [10,20,30,40 sec] Device power-up delay This item appears only when you set the Device power-up delay item to [manual]. ASMB-784 User Manual... -
Page 53: Smart Settings
3.3.9 SMART Settings Figure 3.13 SMART Setting SMART Self Test This item is to enable or disable SMART self test on all HDDs during post. ASMB-784 User Manual... -
Page 54: Super Io Configuration
3.3.10 Super IO Configuration Figure 3.14 Super IO Configuration Figure 3.15 Serial Port 1 Configuration ASMB-784 User Manual... - Page 55 Figure 3.16 Serial Port 2 Configuration Figure 3.17 Parallel Configuration Serial Port 1 Configuration Serial Port “Enable” or “disable” Serial Port 1. ASMB-784 User Manual...
-
Page 56: H/W Monitor
Enable/Disable the chassis Intrusion monitoring function. When enabled and the case is opened, a warning message will show in post screen. CPU Warning Temperature Use this to set the CPU warning temperature threshold. When the system reaches the warning temperature, the speaker will beep. ASMB-784 User Manual... -
Page 57: Serial Port Console Redirection
Smart Fan Enable or Disable CPU FAN and System FAN Mode to SMART FAN setting. 3.3.12 Serial Port Console Redirection Figure 3.19 Serial Port Console Redirection Console Redirection Enable or disable the console redirection feature. ASMB-784 User Manual... - Page 58 Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. Options available: 1/2. ASMB-784 User Manual...
- Page 59 Enables or disables extended terminal resolution. Options available: Enabled/Disabled. Legacy OS Redirection Resolution On Legacy OS, the number of Rows and Columns supported redirection. Options available: 80x24/80X25. Putty Keypad To support selection function key and keypad on Putty. ASMB-784 User Manual...
-
Page 60: Chipset
Chipset Figure 3.21 Chipset 3.4.1 PCH-IO Configuration Figure 3.22 PCH-IO Configuration ASMB-784 User Manual... - Page 61 "power off". Figure 3.23 PCI Express Configuration PCI Express Clock Gating Enable or disable PCIE clock gating for each root port. PCIe-USB Glitch W/A Enable or disable PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG port. ASMB-784 User Manual...
- Page 62 To set ASPM level for PCI Express Slot 2. PCIe Speed To set PCIe speed for PCI Express Slot 2. Detect Non-Compliance Device Detect Non-compliance PCIE device. When this item is enabled, it will take more time during POST. ASMB-784 User Manual...
- Page 63 To set ASPM level for PCI Express Slot 7. PCIe Speed To set PCIe speed for PCI Express Slot 7. Detect Non-Compliance Device Detect Non-compliance PCIE device. When this item is enabled, it will take more time during POST. ASMB-784 User Manual...
- Page 64 Figure 3.26 USB Configuration USB Precondition Pre-condition work on USB host controller and root ports for faster enumeration. XHCI Mode Mode of operation of XHCI controller. USB Ports Pre-Port Disable Control Enable or disable USB port#0~13. ASMB-784 User Manual...
- Page 65 Figure 3.27 PCH Azalia Azalia Control detection of Azalia device. Figure 3.28 LAN Configuration LAN1/LAN2/LAN3/LAN4 Controller Enable or disable onboard LAN1/LAN2/LAN3/LAN4. ASMB-784 User Manual...
-
Page 66: System Agent (Sa) Configuration
Enable or disable boot options for legacy network devices. Wake on LAN1 Enable or disable integrated LAN to wake the system. 3.4.2 System Agent (SA) Configuration Figure 3.29 System Agent (SA) Configuration VT-d To enable or disable VT-d function on MCH. ASMB-784 User Manual... - Page 67 This item is to select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem This item is to select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device. Gfx Low Power Mode This option is applicable for SFF only ASMB-784 User Manual...
- Page 68 OpROM. PEG0~2 De-emphasis Control Configure the De-emphasis control on PEG0~2. PEG0~2 ASPM To control ASPM support for the PEG Device, and this item has no effect if PEG is not the currently active device. ASMB-784 User Manual...
- Page 69 3.4.2.3 Memory Configuration Figure 3.32 Memory Configuration Memory Frequency Limiter To set the maximum memory frequency between [1067],[1333] and [1600]. ASMB-784 User Manual...
-
Page 70: Boot
“On” or “Off” power-on state for the NumLock Quiet Boot If this option is set to Disabled, the BIOS displays normal POST messages. If Enabled, an OEM Logo is shown instead of POST messages. Boot Option Priorities Choose boot priority from boot device. ASMB-784 User Manual... - Page 71 This item is a BIOS reaction on INT19 trapping by Option ROM. When it's set as "Immediate", the trap will be executed right away. When it's set as "Postponed", the trap will be executed during legacy boot. ASMB-784 User Manual...
-
Page 72: Security
Security Figure 3.35 Security Select Security Setup from the ASMB-784 Setup main BIOS setup menu. All Security Setup options, such as password protection, are described in this section. To access the sub menu for the following items, select the item and press <Enter>. -
Page 73: Save & Exit
Select this option to discard your changes. Restore Defaults Select this option to restore BIOS configuration as origin. Save as User Defaults Select this option to save user's configuration. Restore User Defaults Select this option to restore BIOS to user's configuration. ASMB-784 User Manual... -
Page 74: Server Management
If enabled, the motherboard will wait 60 seconds until BMC (IPMI-1000 Module) boots up completely, after which a normal BIOS post screen will be displayed. If dis- abled, the motherboard will not wait for the BMC's (IPMI-1000 Module) response. ASMB-784 User Manual... -
Page 75: Bmc Self Test Log
3.8.1 BMC Self Test Log Figure 3.38 BMC Self Test Log Erase Log Erase log options When Log is Full Select the action to be taken when log is full ASMB-784 User Manual... -
Page 76: System Event Log
Choose options for erasing SEL When SEL is Full Choose options for reactions to a full SEL Log EFI Status Codes Disable the logging of EFI status codes or log only error code or only progress code or both ASMB-784 User Manual... -
Page 77: Bmc Network Configuration
BMC Network Configuration Figure 3.40 BMC network configuration Configuration Address Source Select to configure LAN channel parameters statically or dynamically (by BMC /IPMI- 1000 module). Unspecified will not modify any BMC (IPMI-1000 module) network parameters during BIOS posting phase. ASMB-784 User Manual... - Page 78 ASMB-784 User Manual...
-
Page 79: Chapter 4 Chipset Software Installation Utility
Chapter Chipset Software Installation Utility... -
Page 80: Before You Begin
Before You Begin To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the ASMB-784 are located on the software installation CD. Note! The files on the software installation CD are compressed. Do not attempt to install the drivers by copying the files manually. -
Page 81: Windows Os Driver Setup
Insert the driver CD into your system's CD-ROM drive. You can see the driver folders items. Move the mouse cursor over the folder "01-Chipset". In CSI folder, you can click find an executable file to complete implementation of the driver. ASMB-784 User Manual... - Page 82 ASMB-784 User Manual...
-
Page 83: Chapter 5 Vga Setup
Chapter VGA Setup... -
Page 84: Introduction
Insert the driver CD into your system's CD-ROM drive. You can see the driver folders items. Navigate to the "02-HD Graphics" folder and click the executable file to com- plete the installation of the drivers for Windows® OS. ASMB-784 User Manual... -
Page 85: Chapter 6 Lan Configuration
Chapter LAN Configuration... -
Page 86: Introduction
Introduction The ASMB-784 has two or four Gigabit Ethernet LANs via dedicated PCI Express x1 lanes (GbE LAN1: Intel I217LM; GbE LAN2/3/4: Intel I210-AT that offer bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet at 1000 Mbps. -
Page 87: Chapter 7 Intel Me
Chapter Intel ME... -
Page 88: Introduction
The integrated Intel® gigabit Ethernet controller supports all major network operating systems. However, the installation procedure varies with different operating systems. In the following sections, refer to the one that provides the driver setup procedure for the operating system you are using. ASMB-784 User Manual... -
Page 89: Chapter 8 Intel Usb 3.0
Chapter Intel USB 3.0... -
Page 90: Introduction
Introduction ASMB-784 provides Intel® USB 3.0 and the data transfer rate of USB3.0(5Gbps) is 10 times to USB2.0(480Mbps). Installation Insert the driver CD into your system's CD-ROM drive. Navigate to the ""05. Other" folder and find "Intel USB3.0" folder to install the driver. -
Page 91: Sata Raid Setup
Chapter SATA RAID Setup... -
Page 92: Introduction
User Guide in the driver CD. Path: folder "Intel Rapid Storage Technology" in "05. Other". Note! Before you install the Intel Rapid Storage Technology, please read the "readme.txt" which is in the folder "Intel Rapid Storage Technology" in "05-Other". ASMB-784 User Manual... -
Page 93: Appendix A Programming The Watchdog Timer
Appendix Programming the Watchdog Timer... -
Page 94: Watchdog Timer Overview
The ASMB-784’s watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to pro- gram it. - Page 95 Unlock NCT6776F Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock NCT6776F ASMB-784 User Manual...
-
Page 96: Example Programs
Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx in al,dx Or al,08h Out dx,al ;----------------------------------------------------------- Dec dx; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- ASMB-784 User Manual... - Page 97 Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Set minute as counting unit Mov al,0f5h Out dx, al Inc dx In al,dx Or al, 08h ASMB-784 User Manual...
- Page 98 Dec dx ; Enable watchdog timer to be reset by mouse Mov al,0f7h Out dx,al Inc dx In al,dx Or al,80h Out dx,al ;----------------------------------------------------------- Dec dx ; lock NCT6776F Mov al,0aah Out dx,al Enable watchdog timer to be reset by keyboard ASMB-784 User Manual...
- Page 99 Mov dx,2eh ; unlock NCT6776F Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable the function of watchdog timer Mov al,30h ASMB-784 User Manual...
- Page 100 Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; lock NCT6776F Mov al,0aah Out dx,al ASMB-784 User Manual...
-
Page 101: Appendix B I/O Pin Assignments
Appendix I/O Pin Assignments... -
Page 102: Parallel Port (Lpt1)
Parallel Port (LPT1) Table B.1: Parallel Port (LPT1) Signal Signal STROBE* GND* AFD* IGND ERR* INIT* ACK* SLIN* BUSY SLCT USB2.0 Header (USB6~11) USB8_9 USB6_7 USB10_11 Table B.2: USB Header (USB6~11) Signal Signal USB_VCC5 USB_VCC5 USB_D- USB_D- USB_D+ USB_D+ ASMB-784 User Manual... -
Page 103: Usb3.0 Header (Usb2_3)
Table B.3: USB 3.0 Header (USB2_3) Signal Signal +5V_USB2_3 USB3_RX_DN5 +5V_USB2_3 USB3_RX_DP5 USB3_RX_DN6 USB3_RX_DP6 USB3_TX_DN5 USB3_TX_DP5 USB3_TX_DN6 USB3_TX_DP6 USB2_N2 USB2_P2 USB2_N3 USB_OC USB2_P3 VGA Connector (VGA) Table B.4: VGA Connector (VGA) Signal Signal GREEN BLUE H-SYNC V-SYNC ASMB-784 User Manual... -
Page 104: Interface (Com2)
RS-232 Interface (COM2) Table B.5: RS-232 Interface (COM2) COM1/COM2 Signal SOUT External Keyboard and Mouse Connector (KBMS2) Table B.6: External Keyboard and Mouse Connector (KBMS2) Signal KB CLK KB DATA MS DATA MS CLK ASMB-784 User Manual... -
Page 105: System Fan Power Connector (Sysfan0~3)
Power LED and Keyboard Lock (JFP3) Table B.8: Power LED and Keyboard Lock (JFP3) Function LED power + (3.3 V) LED power - #keylock Ground External Speaker Connector (JFP2) Table B.9: External Speaker Connector (JFP2) Function SPK_VCC SPK_OBS SPK_BUZ SPK_OUT ASMB-784 User Manual... -
Page 106: Reset Connector (Jfp1)
Reset Connector (JFP1) Table B.10: Reset Connector (JFP1) Signal RESET B.11 HDD LED Connector (JFP2) Table B.11: HDD LED Connector (JFP2) Signal HDD_LED+ HDD_LED- B.12 ATX Soft Power Switch (JFP1) Table B.12: ATX Soft Power Switch (JFP1) Signal PWR-BTN ASMB-784 User Manual... -
Page 107: Usb/Lan Ports (Lan1_Usb01 And Lan2_Usb23)
Table B.14: Giga LAN 10/100/1000 Mbps RJ-45 port Signal Signal MID0+ MID2+ MID0- MID2+ MID1+ MID3+ MID1- MID3+ B.14 Front Panel Audio Connector (FPAUD1) Table B.15: Front Panel Audio Connector (FPAUD1) Signal MIC2_L AGND MIC2_R PRESENSE LIN2_R MIC_DEC FIO_JD LIN2_L LINEOUT2_DEC ASMB-784 User Manual... -
Page 108: 8-Pin Alarm Board Connector (Volt1)
B.16 Case Open Connector (JCASE1) Table B.17: Case Open Connector (JFP1) Signal CASEOP B.17 Front Panel LAN LED Connector (LAN_LED1/2) Table B.18: LAN LED Connector (LAN_LED1/2) Signal Signal LAN1/3_LED0_ACT LAN2/4_LED1_ACT VCC3_LAN1/3LED VCC3_LAN2/4LED LAN1/3_LED1_1000M LAN2/4_LED2_1000 LAN1/3_LED2_100M LAN2/4_LED0_100 VCC3 ASMB-784 User Manual... -
Page 109: Spi_Cn1: Spi Flash Card Pin Connector
Interrupt controller 2, programmable interrupt controller 0C0-0DF DMA controller 0F0-0F0 Numeric data processor A35-A36 On-board hardware monitor 2F8-2FF Serial port 2 778-77F Printer port (LPT1) 3B0-3BB Intel HD Graphics 3C0-3DF Intel HD Graphics 3F8-3FF Serial port 1 ASMB-784 User Manual... -
Page 110: Interrupt Assignments
1st MB Memory Map Table B.23: 1st MB memory map Addr. range (Hex) Device E0000h - FFFFFh BIOS CC000h - DFFFFh Unused C0000h - CBFFFh VGA BIOS A0000h - BFFFFh Video Memory 00000h - 9FFFFh Base memory ASMB-784 User Manual... - Page 111 ASMB-784 User Manual...
- Page 112 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2013...