Titan 440ix Owner's Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Paint Sprayer
  5. 440ix
  6. Owner's manual

Titan 440ix Owner's Manual

Airless sprayer
Hide thumbs Also See for 440ix:
Table of Contents

Advertisement

Quick Links

Do not use this equipment before reading this manual!
NOTE: This manual contains
important warnings
and instructions.
Please read and retain
for reference.
Model Numbers:
Skid Basic
Skid Loaded
High Rider Basic
High Rider Loaded
Printed in the U. S. A.
440
Airless Sprayer
700-3030
700-3035
700-3040
700-3045
Owner's Manual
For professional use only
ix
X-Lock Theft Deterrent System
Security Code
— — — —
0105 © 2005 Titan Tool Inc. All rights reserved. Form No. 313-2459A

Advertisement

Table of Contents
loading

Related Manuals for Titan 440ix

Summary of Contents for Titan 440ix

  • Page 1 X-Lock Theft Deterrent System Skid Basic 700-3030 Security Code Skid Loaded 700-3035 High Rider Basic 700-3040 — — — — High Rider Loaded 700-3045 0105 © 2005 Titan Tool Inc. All rights reserved. Form No. 313-2459A Printed in the U. S. A.

  • Page 2: Table Of Contents

    Do not use plastic drop cloths when PREVENTION: spraying flammable materials. • NEVER aim the gun at any part of the body. • Use lowest possible pressure to flush equipment. © Titan Tool Inc. All rights reserved.

  • Page 3: Specifications

    When the sprayer is used with a generator or uncontrolled couplings. Immediately replace hose if any of those line voltage, the use of Titan’s “Line Surge Protector” (P/N conditions exist. Never repair a paint hose. Replace with 800-935) is recommended.

  • Page 4: General Description

    NOTE: Hold the return hose in the waste 8. Plug the power cord into a properly grounded outlet at container when moving the least 25’ from the spray area. PRIME/SPRAY valve to PRIME in case the sprayer is pressurized. © Titan Tool Inc. All rights reserved.

  • Page 5: Painting

    11. Unlock the gun by turning the gun trigger higher pressure and the PRIME/SPRAY valve is lock to the unlocked position. in the SPRAY position, either the spray tip is worn or the sprayer is in need of service/repair. © Titan Tool Inc. All rights reserved.

  • Page 6: Xact Digital Control System Operation

    Pressing the #4 key selects the active menu screen or timers and a screen that allows the user to reset the timers. performs a function described on the active menu screen. © Titan Tool Inc. All rights reserved.

  • Page 7: Pressure Relief Procedure

    As a result, the Main Screen will appear at sprayer startup. NOTE: If there is no action at any menu screen for 30 seconds, the display will go back to the Main Screen. © Titan Tool Inc. All rights reserved.

  • Page 8: Spraying

    Begin movement of the gun Shrubs next to houses should be tied back and covered with a before the trigger is pulled. canvas cloth. The cloth should be removed as soon as possible. Titan gun extensions are extremely helpful in these start pull release situations.

  • Page 9: Cleanup

    Always contact the supplier of solvents OFF position. for recommendations. 10. Move the PRIME/SPRAY valve up to its 4. If you have any further questions concerning your TITAN SPRAY position. Airless Sprayer, call TITAN: 11. Turn on the sprayer.

  • Page 10: Replacing The Motor

    Panel Screw Control Panel Motor Armature Gear Motor Mounting Gear and Crank Screw Assembly Thrust Washer Pump Housing 2nd Stage Gear Front Cover Pump Housing Front Cover Screw Front Cover Front Cover Screw © Titan Tool Inc. All rights reserved.

  • Page 11: Replacing The Transducer

    (refer to the electrical schematic in the Parts List section of this manual). 12. Reassemble the pump by reversing steps 1–7. Pump Front Housing Cover T-Slot Front Cover Screw Pump Transducer Block Assembly Pump Block Mounting Screw © Titan Tool Inc. All rights reserved.

  • Page 12: Servicing The Fluid Section

    13. Using a wrench, tighten the retainer nut securely. 14. Slide the top of the piston rod into the T-slot on the slider assembly. © Titan Tool Inc. All rights reserved.

  • Page 13: Replacing The Filters

    4. Turning counterclockwise, thread the new or cleaned filter into the pump block. 5. Slide the filter housing over the filter and thread it into the pump block until secure. Filter Housing Filter Seal Pump Block © Titan Tool Inc. All rights reserved.

  • Page 14: Troubleshooting

    4. Faulty or loose wiring. 4. Inspect or take to a Titan authorized service center. 5. Excessive motor temperature. 5. Allow motor to cool.

  • Page 15: Xact Digital Control System Error Messages

    Xact Digital sprayer. Once a problem occurs and the error message Control System has risen too high. Take the sprayer to a Titan appears, the sprayer will shut down. authorized service center for repair.
  • Page 16 • Tous les accessoires doivent être homologués pour une pression égale ou supérieure à 3300 lb/po2 / 22.8 MPa. Cela s'applique, entre autres, aux têtes de pulvérisation, aux accessoires du pistolet et aux flexibles. © Titan Tool Inc. Tous droits réservés. Français...
  • Page 17 égale ou supérieure à 3300 lb/po2 / 22.8 MPa. • Ne jamais pulvériser lorsqu'il vente. • Porter des vêtements pour protéger la peau et les cheveux contre tout contact avec la peinture. © Titan Tool Inc. Tous droits réservés. Français...
  • Page 18 • Todos los accesorios deben tener una capacidad de 3300 para obtener información completa de seguridad. lb/pulg2 / 22.8 MPa o mayor. Esto incluye las boquillas de atomizador, pistolas, extensiones y mangueras. © Titan Tool Inc. Todos los derechos reservados. Español...
  • Page 19 3300 lb/pulg2 / 22.8 MPa o mayor. • No atomice en días con viento. • Use ropa que evite el contacto de la pintura con la piel y el cabello. © Titan Tool Inc. Todos los derechos reservados. Español...

  • Page 20: Parts Listings

    Parts List Main Assembly High Rider Model © Titan Tool Inc. All rights reserved.

  • Page 21: Skid Assembly

    761-188 Screw............2 704-109 O-ring (for hot solvents, optional) 700-1024 Elbow ............1 704-179 Leg, left, complete 704-127 Retaining clip ..........1 (includes items 1–4) 755-135 Clip (not shown)..........1 704-178 Leg, right, complete (includes items 5–10) © Titan Tool Inc. All rights reserved.

  • Page 22: Fluid Section Assembly

    Fluid Section Assembly (Skid P/N 704-538, High Rider 704-571) Install upper packing with raised lip and O-ring facing down. O-Ring Raised Lip Beveled Edge Install lower packing with the beveled edge facing up. © Titan Tool Inc. All rights reserved.

  • Page 23: Drive Assembly

    Transducer assembly (includes item 5)..1 700-2060 Slider assembly ..........1 704-584 Transducer o-ring ........1 704-548 Transducer jumper wire (not shown) ..1 704-588 Electronic pressure control (EPC) ....1 704-589 Motor............1 704-522 Motor assembly (includes items 6 and 7) © Titan Tool Inc. All rights reserved.

  • Page 24: High Rider Cart Assembly

    Potentiometer Transducer Jumper WHITE GREEN Ground Motor AC-Motor AC-Motor BLACK AC-Line AC-Neut Control Panel Electronic Pressure Board Control (EPC) WHITE WHITE NOTE: All electrical work should be performed by an authorized service center. © Titan Tool Inc. All rights reserved.

  • Page 25: Accessories

    S-3 Stainless Steel Airless Gun • 3900 PSI • Stainless Steel fluid passages • High Pressure Swivel • In-handle filter • 4-finger trigger pull Part No. Description 550-250 ...S-3 — 4 Finger Gun © Titan Tool Inc. All rights reserved.
  • Page 26 Notes © Titan Tool Inc. All rights reserved.
  • Page 27 Notes © Titan Tool Inc. All rights reserved.

  • Page 28: Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge...

Table of Contents