Advertisement

Quick Links

PowrTwin 6900
Register your product online at:
www.titantool.com
Proper registration will serve as proof of purchase in the event your
original receipt becomes misplaced or lost.
_ _ _ _ _ _ _ _ _ _
Serial Number
Printed in the U.S.A.
SPEEFLO
Owner's Manual
For professional use only
Do not use this equipment
before reading this manual!
XLT
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.
Model Numbers:
Gas Bare
Gas Complete
Gas Complete w/ Heavy
Duty Bypass Valve
230V Electric Bare
230V Electric Complete 448-370
© Titan Tool Inc. All Rights Reserved. Form No. 0528914C
0314
DI
448-350
448-355
448-360
448-365

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SPEEFLO PowrTwin 6900XLT DI and is the answer not in the manual?

Questions and answers

Summary of Contents for Titan SPEEFLO PowrTwin 6900XLT DI

  • Page 1 230V Electric Bare 448-365 _ _ _ _ _ _ _ _ _ _ 230V Electric Complete 448-370 Serial Number © Titan Tool Inc. All Rights Reserved. Form No. 0528914C 0314 • Printed in the U.S.A.
  • Page 2: Important Safety Information

    (add more hose if necessary). Flammable vapors are often heavier than air. Floor area must be extremely well ventilated. The pump contains arcing parts that emit sparks and can ignite vapors. © Titan Tool Inc. All rights reserved.
  • Page 3: Grounding Instructions

    If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. Grounded Outlet IMPORTANT: Do not lift by cart handle when loading or unloading. Grounding Pin Cover for grounded outlet box © Titan Tool Inc. All rights reserved.
  • Page 4: Table Of Contents

    26” W (66 cm) x 35” H (89 cm) Fluid section wetted parts: Electroless nickel plated ductile iron, electroless nickel plated carbon steel, stainless steel, tungsten carbide, Teflon, thiokol impregnated leather, ultra high molecular weight polyethylene. © Titan Tool Inc. All rights reserved.
  • Page 5: Introduction

    Congratulations on having selected the finest airless sprayer engine speed under normal load, change brands available in the world. Titan piston pumps are tireless of gasoline. If spark knock or pinging persists, workhorses — so tough they are virtually indestructible, even consult an authorized dealer of the engine under the most severe service.
  • Page 6: Operating The Swing Cart

    Make sure the second gun outlet remains plugged. 4. Fill the oil cup 1/2 full with Titan Piston Lube (P/N 314-480) supplied by the factory. This extends packing life. 5. Check the hydraulic fluid level daily before starting the sprayer.
  • Page 7: Preparing A New Sprayer

    OFF position. To turn off the electric motor, • set the pressure to minimum by turning the pressure control knob fully counterclockwise, • move the ON/OFF switch to the OFF position. © Titan Tool Inc. All rights reserved.
  • Page 8: Preparing To Paint

    13. Unlock the gun by turning the gun trigger lock to the Starter Rope Lever to the ON position, unlocked position. • pull the starter rope briskly until the engine starts. To start the electric motor, move the ON/OFF switch to the ON position. © Titan Tool Inc. All rights reserved.
  • Page 9: Pressure Relief Procedure

    3. Place the siphon tube into a container of the appropriate solvent. IMPORTANT: Use only compatible solvents when cleaning out oil based enamels, lacquers, coal tar, and epoxies. Check with the fluid manufacturer for the recommended solvent. © Titan Tool Inc. All rights reserved.
  • Page 10: Cleaning A Clogged Tip

    Cleaning the Inlet Screen IMPORTANT: Do not store the unit under pressure. 1. Loosen and remove the inlet screen Siphon from the siphon tube. Tube 2. Clean thoroughly with the appropriate solvent. Inlet Screen © Titan Tool Inc. All rights reserved.
  • Page 11: Maintaining The Filter Assembly

    Inspect all parts of the filter assembly before reassembly. 2. Change the hydraulic fluid every twelve months. Drain the old fluid from the tank and fill with 4 quarts of Titan 1. Inspect the ball inside the filter element. If the ball has Coolflo™...
  • Page 12: Basic Engine Maintenance (Gas Engine)

    NOTE: Brushes should be replaced when they are worn to less than 1/2 inch. Check and replace both For CSA approved sprayers only: The ON/OFF switch is brushes at the same time. also the RESET! © Titan Tool Inc. All rights reserved.
  • Page 13: Troubleshooting

    Hose size or length is too small or too long Increase hose size to minimize pressure drop through hose and/or reduce hose length. Solvent has caused upper packing to swell Replace packing. Pump chatters on up or down stroke © Titan Tool Inc. All rights reserved.
  • Page 14: Hydraulic Motor

    NOTE: Engine labors at stall on if the head becomes hotter. This will help determine both strokes. if center o-ring is blown on spool valve. If hot, remove and replace o-ring. Bad hydraulic pump Replace hydraulic pump. © Titan Tool Inc. All rights reserved.
  • Page 15: Spray Patterns

    Remove restrictions in system; clean tip screen if filter is used. Round pattern Worn tip Replace tip. Fluid too heavy for tip Increase pressure. Thin material. Change nozzle tip. © Titan Tool Inc. All rights reserved.
  • Page 16 3300 PSI. Ceci est valable de chiffons et autres matières inflammables. Français © Titan Tool Inc. Tous droits réservés.
  • Page 17: Sécurité Du Moteur À Essence

    13. Ne pulvérisez pas à l’extérieur par temps venteux. 14. Débranchez toujours le cordon électrique de la prise avant de travailler sur l’équipement. IMPORTANT: Ne pas soulever par la poignée du chariot lors du chargement ou du déchargement. © Titan Tool Inc. Tous droits réservés. Français...
  • Page 18: Información De Seguridad Importante

    11. Antes de utilizar el aparato, verifique que todas las que pulverice. Lea las hojas de datos sobre seguridad conexiones son seguras. de los materiales (MSDS) y las etiquetas en los botes de Español © Titan Tool Inc. Todos los derechos reservados.
  • Page 19 13. No pulverice al aire libre si hace viento. 14. Desenchufe siempre el cable antes de trabajar en el equipo. IMPORTANTE: No cargue el equipo por el asa del carrito durante la carga y descarga. © Titan Tool Inc. Todos los derechos reservados. Español...
  • Page 20: Parts Lists And Service Instructions

    Hose clamp ..........1 (electric model, includes belt, not shown) 1 ---------- Belt guard assembly .........1 506-251 Convertokit, 3 HP, electric, 230V ---------- Hydraulic system ........1 (electric model, not shown).......1 449-181 Belt, “V” (gas model) .........1 © Titan Tool Inc. All rights reserved.
  • Page 21: Cart Assembly

    Belt guard, 230V electric model 858-636 Screw ............2 858-002 Lockwasher ..........2 862-411 Nut ............1 449-185 Belleville washer ........1 862-001 Flat washer ..........1 449-187 Clip ............1 449-198 Flat washer ..........1 449-166 Bolt ............1 759-074 Label (not shown) © Titan Tool Inc. All rights reserved.
  • Page 22: Servicing The Hydraulic Motor

    6. The piston rod (21) should be near the top of its stroke for 2–4, 6, 8, 9, 12, 18, 19, and 24) disassembly. It may be necessary to use a wood or nylon driver to push the piston rod up to its top position. © Titan Tool Inc. All rights reserved.
  • Page 23 Check valve rod assembly (20) for normal spring action at this time. 6. Install piston seal (18) with lips facing downward. Carefully install o-ring (19). Expand the ring and stretch it sufficiently for installation. © Titan Tool Inc. All rights reserved.
  • Page 24: Fluid Section

    Fluid section service kit, minor (includes items 1, 3, 4, 10, 12, 16, 19, 21, and Loctite P/N 426-051) 451-133 Foot valve assembly (includes items 18–24) 236-050 Outlet valve assembly (includes items 9–13) © Titan Tool Inc. All rights reserved.
  • Page 25: Servicing The Fluid Section

    IMPORTANT: Use of non-Titan service parts may void Loctite is only on the threads. warranty. Ask for original parts made by Titan for best 9. Place the lower packing spring (8) onto the outlet valve services. This pump should receive a routine servicing housing (13) followed by the spring retainer (7).
  • Page 26: Hydraulic System

    Torque to 8 FT/LBS (11 N/m) Use hydraulic sealant Use hydraulic sealant Use hydraulic sealant Torque to 15 FT/LBS (20,5 N/m) Torque to 15 FT/LBS (20,5 N/m) Torque to 15 FT/LBS (20,5 N/m) © Titan Tool Inc. All rights reserved.
  • Page 27: Gas Convertokit

    977-228 Pulley ............1 590-068 Handle grip ..........1 335-017 Handle ............1 860-552 Screw ............2 459-018 Mount plate ..........1 506-255 Rectifier (not shown) .........1 506-258 Fan (not shown)........1 449-181 Belt, “V” (not shown) ....... 1) © Titan Tool Inc. All rights reserved.
  • Page 28: Electric Convertokit, 230V

    Handle grip ..........1 944-031 Valve housing ...........1 335-016 Handle ............1 944-039 Ball ............1 449-181 Belt, “V” 944-043 Valve seat ..........1 (not shown, not part of assembly) 944-044 Valve seal ..........1 944-013 Valve seat retainer........1 © Titan Tool Inc. All rights reserved.
  • Page 29: Filter Assembly

    NPSM(M) hose connection 945-026 Valve stem stop ........1 (1) 3/8” NPT(F) plugged for 891-183 O-ring, Teflon ..........1 additional gun hookup Wetted Parts ........Carbon steel with electroless nickel plating, stainless steel, tungsten carbide, Teflon © Titan Tool Inc. All rights reserved.
  • Page 30: Gun Manifold Assemblies (Optional)

    1 Gun Add-On, 1/4” ....1 ...... 1 ...... 1 975-311 1 Gun Add-On, 3/8” ..................1 ...... 1 .......1 975-200 Add-A-Gun Kit, 1/4” ....1 ...... 2 ...... 3 975-300 Add-A-Gun Kit, 3/8” ..................1 ...... 2 .......3 © Titan Tool Inc. All rights reserved.
  • Page 31: Sae O-Ring Fitting Installation

    Accessories and Service Kits SAE O-Ring Fitting Installation These items may be purchased separately from your local Titan Steps 1 & 2: distributor. Lubricate Part # Description 103-830 5 Gal. Siphon Hose Assembly w/Rock Catcher Lubricate 1” x 4.5’ 103-808 55 Gal.
  • Page 32: Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s...

This manual is also suitable for:

448-350448-355448-360448-365448-370

Table of Contents