Subscribe to Our Youtube Channel
Related Manuals for Cleveland KGL
Summary of Contents for Cleveland KGL
- Page 1 INSTALLATION, OPERATION AND REPAIR MANUAL GAS KETTLE MODEL # KGL-T CLEVELAND RANGE INC. 1333 East 179th St. Cleveland, Ohio U.S.A. 44110 (216)481-4900 222-01CO 9102 REV:0 KET-07...
- Page 2 IMPORTANT THE FOLLOWING POINTS ARE TO INSURE THE SAFE INSTALLATION AND OPERATION OF THIS EQUIPMENT : INSURE ALL GAS AND ELECTRICAL SUPPLIES MATCH RATING PLATE AND ELECTRICAL STICKERS OBSERVE ALL CLEARANCE REQUIREMENTS DISCONNECT THE ELECTRICAL POWER SUPPLY TO THE APPLIANCE BEFORE CLEANING OR SERVICING UNIT ONLY A QUALIFIED SERVICE TECHNICIAN SHOULD REPAIR UNIT THE INSTALLATION AND CONNECTION MUST COMPLY WITH LOCAL CODES, OR IN...
-
Page 3: If You Smell Gas
FOR YOUR SAFETY Gas fired kettles are only to be installed under a ventilation hood in a room which has DO NOT STORE OR USE GASOLINE OR provisions for adequate make up air. OTHER FLAMMABLE LIQUIDS AND VAPOURS IN THE VICINITY OF THIS OR Electrical installation must be in accordance ANY OTHER APPLIANCE. - Page 4 Arrange for the carrier's pipe joint compound which is resistant to representative to examine the L.P. gas. Test all pipe joints for leaks with damage. soap and water solution. Ensure that the gas pressure regulator is set for the manifold Fill out all carrier claims forms and pressure indicated on the gas rating plate.
-
Page 5: Operation
CARE AND CLEANING NOTE: When cooking egg and milk products, the kettle should not be preheated, as products Your Cleveland kettle must be cleaned of this nature adhere to hot cooking surfaces. regularly to maintain its fast, efficient cooking These types of food should be placed in the performance, and to ensure its continued safe, kettle before heating is begun. -
Page 6: Maintenance
In a sink, wash and rinse the MAINTENANCE valve stem, hex nut, and Cleveland kettles require very little knob. Wash and rinse the preventive maintenance, other than daily inside of the valve body using cleaning. -
Page 7: Kettle Venting Instructions
In order to preserve the various agency safety gauge shows at least 5 psi pressure. Any certification (UL, A.G.A., CSA. CGA, NSF, bubbles which appear will indicate a leak. ASME/Ntl. Bd., etc.), only factory-supplied replacement parts should be used. The use of other than factory-supplied replacement parts RESERVOIR FILL PROCEDURES will void the warranty. - Page 8 PARTS LIST - ELECTRICAL COMPONENT BOX ASSEMBLY ITEM NO. PART NO. DESCRIPTION QTY. KE51141 Transformer, 120-16V. KE52690 Bushing KE53469 Ignition module KE00458 Solid state control KE50753 Relay KE53316 Safety thermostat Brass nut # 7/16-24 05050 KE53436 Air switch KE51164 Transformer 120-24V. KE52281 Fuse bussman MDL-1/2 amp KE51139...
- Page 9 PARTS LIST - PRESSURE RELIEF ASSEMBLY ITEM-NO. PART NO. DESCRIPTION QTY. FI05215 Cap, 1/2" FI05225 Nipple, 1/2" FI00151 Street elbow, 1/2" KE51014 Check valve FI00596 Nipple FI05214 Cross tee RT00370 Tubing, 1/4" copper(per ft.) KE51723 Safety valve, 50 p.s.i FI00598 Nipple FI052l Elbow...
- Page 10 PARTS LIST - GAS CONTROL ASSEMBLY ( KETTLE ) ITEM NO. PART NO. DESCRIPTION QTY. KE53402 Air orifice, 140K BTU burner KE53402-1 Air orifice, 170K BTU burner KE01426 Mixing chamber KE53387 Swivel Pipe KE53515 Gas control valve, N.G. KE535151 Gas control valve, L.P. F01518 Shut-off valve Reducer...
- Page 11 GAS CONTROL ASSEMBLY ( KETTLE )
- Page 12 PARTS LIST - SIDE BOX ASSEMBLY (KETTLE) ITEM NO. PART NO. DESCRIPTION QTY. Sight glass KE53437 Igniter KE01432 Enclosure cover assembly KE00515 Thermistor KE517111 R.H. Trunnion bearing KE52833 Gear KE50315 Worm KE50245 Bearing KE51738 Sleeve, bearing FA10623 Bolt, hex bead FA20029 FA950551 FA95008...
- Page 13 SIDE BOX ASSEMBLY ( KETTLE )
- Page 14 PARTS LIST - 2" TANGENT DRAW-OFF VALVE ITEM NO. PART NO. DESCRIPTION QTY. 1. to 7. KE50972-B Draw-off assembly KE509721 Draw-off assembly, for KDM-40-T FA21008 Hex nut FA95049 Wing nut FA11134 Screw, for KDM-40-T KE527551 Knob KE52754 Hex nut KE52753 Retainer KE52752 Piston...
- Page 15 PARTS LIST - HINGE ASSEMBLY ITEM NO. PART NO. DESCRIPTION QTY. 1. - 9. KE00598 Hinge assembly (40 gal. and under) SK00168 Hinge assembly (60 gal. and over) KE51218 Body, spring assist hinge KE50824 Hinge bearing KE50823 Pin (hinge) KE50820 Insert, brass adjustment KE50819 End piece...
Need help?
Do you have a question about the KGL and is the answer not in the manual?
Questions and answers