Orion OPM-4240 User Manual page 31

OPM-4240 / OPM-4240R
Data
-
Index ID Set Data Bit Read/Write
Size
1 byte 1 byte 1 byte
Value
Variable 0x04 0x00
Length
-
: Length value is 0x08, because currently only 32bit configuration is applied.
Check Sum
-
: Add all the values in "Data" area. Then perform "NOT" operation.
3.19. Graphic User Mode Control
Command for controlling Brightness, Contrast, Sharpness, Color and Tint by User
-
Command Code
-
: 0x8A (Brightness), 0x8B (Contrast), 0x8C (Sharpness), 0x8D (Color), 0x8E (Tint)
One way communication (Send to PDP)
-
Data: ID(1 byte) + Control Data(1 byte)
-
The range of Control Data value and Applicable Input Mode
-
* All Input Mode: Brightness ("0" ~ "100"), Contrast ("0" ~ "100"), and Sharpness ("0" ~ "28")
* DTV, DVD, S-Video, Vide Input Mode: Color ("0" ~ "100"), Tint ("0" ~ "90")
Caution: Adjusted value cannot be applied during "Stand-by" or "No signal" status. There must be input signal for each
input mode to apply adjusted value, while MPDP is operated.
e.g.) Adjust Brightness "47(0x2F)" for MPDP ID No.1
-
STX CMD Length
Value 0x02 0x8A 0x02
If you want to apply the adjusted value for all MPDP, set the value of ID area as "0x00".
-
3.20. White Balance Control
Command for controlling Gain R/G/B and Offset R/G/B of White Balance by user
-
Command Code
-
: 0xAC (Gain R), 0xAD (Gain G), 0xAE (Gain B), 0xB0 (Offset R), 0xB1 (Offset G), 0xB2 (Offset B)
One way communication (Send to PDP)
-
Data; ID (1 byte) + Control Data (1 byte)
-
The range of Control Data: "0 (0x00)" ~ "255 (0xFF)"
-
Caution 1: Although ID area value is set as "0x00" to apply the same value to all MPDP, White balance may not be adjusted
due to the deviation between sets. So, individual White Balance adjustment is recommended.
Caution 2: Adjusted value cannot be applied during "Stand-by" or "No signal" status. There must be input signal for each
input mode to apply adjusted value, while MPDP is operated.
e.g.) Adjust Gain R "240(0xF0) for MPDP ID No. 1
-
STX CMD Length
Value 0x02 0xAC 0x02
3.21. RGB/DTV/DVD Data Control
Command for adjust RGB value of PC input and Gain R/G/B and Offset R/G/B of Component input
-
Command Code (PC RGB, DTV, DVD Identity)
-
: 0xB5 (Gain R), 0xB6 (Gain G), 0xB7 (Gain B), 0xB8 (Offset R), 0xB9 (Offset G), 0xBA (Offset B)
One way communication (Send to PDP)
-
Data: ID (1 byte) + Control Data (2 byte)
-
Control Data
-
: Data Range : "0 (0x00)" ~ "1023 (0x3FF)"
: Control Data 0 (Upper Byte), Control Data 1 (Lower Byte)
Ex) 511(0x1FF) → Control Data0: 0x01, Control Data1: 0xFF
10(0x0A) → Control Data0: 0x00, Control Data1: 0x0A
Address BIC Data
1 byte 4 byte
Variable Variable
ID Control Data ETX
0x01 0x2F 0x03
ID Control Data ETX
0x01 0xF0 0x03
58
Caution 1: Although ID area value is set as "0x00" to apply the same value to all MPDP, White balance may not be adjusted
due to the deviation between sets. So, individual White Balance adjustment is recommended.
Caution 2: Adjusted value cannot be applied during "Stand-by" or "No signal" status. There must be input signal for each
input mode to apply adjusted value, while MPDP is operated.
Caution 3: Input mode should be decided before execute this command. Since Command Code is used for PC, DTV and DVD
commonly, execute Multi-Scale command or Input Mode Change Command to adjust value for the exact input
mode.
e.g.) Adjust Gain R "360(0x168)" of DTV Mode for MPDP ID No.1
-
STX CMD Length
Value 0x02 0xB5 0x03
e.g.) Adjust Offset R "500(0x1F4)" of PC Mode for MPDP ID No.2
-
STX CMD Length
Value 0x02 0xB8 0x03
3.22. VIDEO Data Control
Command for controlling Brightness, Contrast and Color of Video input
-
Command Code: 0xBE (Brightness), 0xBF (Contrast), 0xC0 (Color),
-
One way communication (Send to PDP)
-
Data: ID (1 byte) + Control Data (1 byte)
-
Control Data Range: "0 (0x00)" ~ "255 (0xFF)"
-
Caution 1: Although ID area value is set as "0x00" to apply the same value to all MPDP, White balance may not be adjusted
due to the deviation between sets. So, individual White Balance adjustment is recommended.
Caution 2: Adjusted value cannot be applied during "Stand-by" or "No signal" status. There must be input signal for each
input mode to apply adjusted value, while MPDP is operated.
- e.g.) Adjust Brightness "128 (0x80)" for MPDP ID No.1
-
STX CMD Length
Value
0x02 0xBE 0x02
3.23. Get Current Status
Command for finding out current PDP status
-
Command Code: 0x87
-
Protocol Format - Two way Communication (Send to PDP, Receive From PDP)
-
Caution: It will not respond during Stand-by. It should be executed only during operating status.
* Send to PDP
STX CMD Length ID
1 byte 1 byte 1 byte 1 byte
Data: ID(1 byte)
-
* Receive From PDP
STX CMD Length Data
1 byte 1 byte 1 byte 31 byte
Infinitely Expandable
ID Control Data ETX
0x01 0x01 0x68 0x03
ID Control Data ETX
0x02 0x01 0xF4 0x03
ID Control Data ETX
0x01 0x80 0x03
ETX
1 byte
Check Sum ETX
1 byte 1 byte
59