Page 1: User Manual
Korenix JetNet 6524G 24-Port Gigabit Stackable Layer 3 Managed Ethernet Switch User Manual Version 1.1, Aug. 2009 www.korenix.com...
Page 3: Table Of Contents
Korenix Technology Co., Ltd. Layer 3 Stackable Switch CONTENTS Introduction........................23 Switch Description....................23 Features ......................23 Front-Panel Components ...................24 LED Indicators....................24 Rear Panel Description ..................24 Management Options ..................25 Web-based Management Interface ..............25 Command Line Console Interface Through the Serial Port or Telnet ....25 SNMP-Based Management................26...
Page 4 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Line Interface Structure and Mode-based CLI .........45 CLI Command Format..................45 CLI Mode-based Topology..................45 Switching Commands ....................48 System Information and Statistics commands............48 6.1.1 show arp ......................48 6.1.2 show calendar ....................48 6.1.3 show eventlog....................49 6.1.4...
Page 5 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.2.3.6 vlan ....................74 6.2.3.7 vlan name ..................74 6.2.3.8 vlan makestatic ..................75 6.2.3.9 protocol group..................75 6.2.3.10 switchport acceptable-frame-type ............76 6.2.3.11 switchport ingress-filtering ..............77 6.2.3.12 switchport native vlan ................78 6.2.3.13 switchport allowed vlan..............79 6.2.3.14 switchport tagging................80 6.2.3.15 switchport priority................81...
Page 6 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.2.7.1 show storm-control ................114 6.2.7.2 storm-control broadcast ..............116 6.2.7.3 storm-control multicast..............117 6.2.7.4 storm-control unicast ............... 118 6.2.7.5 switchport broadcast packet-rate............. 119 6.2.7.6 switchport multicast packet-rate ............120 6.2.7.7 switchport unicast packet-rate ............121 6.2.8...
Page 7 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.3.4 exec-timeout ..................137 6.3.3.5 password-threshold .................137 6.3.3.6 maxsessions ..................138 6.3.3.7 sessions...................138 6.3.3.8 telnet sessions .................139 6.3.3.9 telnet maxsessions ................139 6.3.3.10 telnet exec-timeout ................140 6.3.3.11 show telnet..................141 6.3.4 SNMP Server Commands ................141 6.3.4.1 show snmp..................141...
Page 8 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.8 DHCP Client Commands................161 6.3.8.1 ip dhcp restart ..................161 6.3.8.2 ip dhcp client-identifier ..............161 6.3.9 DHCP Relay Commands................162 6.3.9.1 Show bootpdhcprelay ..............162 6.3.9.2 Bootpdhcprelay maxhopcount ............163 6.3.9.3 Bootpdhcprelay serverip ..............163 Spanning Tree Commands ................164 6.4.1...
Page 9 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.5.4.4 logging syslog ..................187 6.5.4.5 clear logging buffered ..............188 Script Management Commands ...............188 6.6.1 script apply ....................188 6.6.2 script delete ....................189 6.6.3 script list.......................189 6.6.4 script show....................190 User Account Management Commands............190 6.7.1 Show Commands ..................191...
Page 10 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.8.3.3 dot1x login ..................209 6.8.3.4 dot1x system-auth-control ...............209 6.8.3.5 dot1x user ..................210 6.8.3.6 dot1x port-control................210 6.8.3.7 dot1x max-req..................212 6.8.3.8 dot1x re-authentication ..............212 6.8.3.9 dot1x re-reauthenticate..............213 6.8.3.10 dot1x timeout ...................213 6.8.4 Radius Configuration Commands..............214 6.8.4.1...
Page 11 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.9.2.2 cdp run.....................228 6.9.2.3 cdp timer ..................228 6.9.2.4 cdp holdtime ..................229 6.10 SNTP (Simple Network Time Protocol) Commands .........229 6.10.1 Show Commands ..................230 6.10.1.1 show sntp..................230 6.10.2 Configuration Commands................231 6.10.2.1 sntp broadcast client poll-interval ............231 6.10.2.2 sntp client mode................232...
Page 12 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.11.4 dir.........................247 6.11.5 whichboot ....................247 6.11.6 boot-system ....................248 6.11.7 ping......................248 6.11.8 traceroute ....................249 6.11.9 logging cli-command..................250 6.11.10 calendar set ....................250 6.11.11 reload......................251 6.11.12 configure......................251 6.11.13 disconnect ....................252 6.11.14 hostname.....................252 6.11.15 quit.......................253 6.12 Differentiated Service Command..............253...
Page 13 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.3.6 class....................266 6.12.3.7 no class....................267 6.12.3.8 mark ip-dscp ..................267 6.12.3.9 mark ip-precedence .................267 6.12.3.10 police-simple..................268 6.12.3.11 policy-map ..................269 6.12.3.12 policy-map rename ................269 6.12.4 Service Commands ..................269 6.12.4.1 service-policy ...................270 6.12.4.2 no service-policy ................271 6.12.5 Show Commands ..................271...
Page 14 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.14.1.4 show queue cos-queue..............288 6.14.2 Configuration Commands................289 6.14.2.1 queue cos-map ................289 6.14.2.2 queue ip-precedence-mapping ............290 6.14.2.3 queue trust..................291 6.14.2.4 queue cos-queue min-bandwidth.............292 6.14.2.5 queue cos-queue strict ..............293 6.14.2.6 queue cos-queue traffic-shape ............294 6.15...
Page 15 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.2.1.3 show ip interface brief..............308 7.2.1.4 show ip route ...................308 7.2.1.5 show ip route bestroutes..............309 7.2.1.6 show ip route entry ................309 7.2.1.7 show ip route precedence..............310 7.2.1.8 show ip traffic................... 311 7.2.2 Configuration Commands................
Page 16 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.3.2.6 area nssa ..................327 7.3.2.7 area nssa default-info-originate ............328 7.3.2.8 area nssa no-redistribute ..............328 7.3.2.9 area nssa no-summary ..............329 7.3.2.10 area nssa translator-role..............329 7.3.2.11 area nssa translator-stab-intv ............330 7.3.2.12 area range ..................330 7.3.2.13 area stub..................331...
Page 17 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.4.5 bootpdhcprelay minwaittime ................347 7.4.6 bootpdhcprelay serverip ................348 7.4.7 ip dhcp restart....................348 7.4.8 ip dhcp client-identifier.................348 Domain Name Server Relay Commands ............349 7.5.1 Show Commands ..................349 7.5.1.1 show hosts..................349 7.5.1.2 show dns..................349 7.5.1.3...
Page 18 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.6.2.12 ip rip receive version................364 7.6.2.13 ip rip send version................365 Router Discovery Protocol Commands ............365 7.7.1 show ip irdp ....................365 7.7.2 ip irdp......................366 7.7.3 ip irdp broadcast ..................366 7.7.4 ip irdp holdtime ....................367 7.7.5...
Page 19 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.1.2.1 ip dvmrp ...................380 8.1.2.2 ip dvmrp metric ................381 Internet Group Management Protocol (IGMP) Commands ......381 8.2.1 Show Commands ..................381 8.2.1.1 show ip igmp..................381 8.2.1.2 show ip igmp groups................382 8.2.1.3 show ip igmp interface ..............383 8.2.1.4...
Page 20 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.3.2.9 disable ip multicast mdebug mtrace ..........402 Protocol Independent Multicast – Dense Mode (PIM-DM) Commands....402 8.4.1 Show Commands ..................402 8.4.1.1 show ip pimdm.................402 8.4.1.2 show ip pimdm interface ..............403 8.4.1.3 show ip pimdm interface stats ............404 8.4.1.4...
Page 21 Korenix Technology Co., Ltd. Layer 3 Stackable Switch switch renumber ....................421 switch movemanagement.................421 archive copy-sw....................422 archive download-sw..................423 reload .......................423 9.10 session ......................424 Web-Based Management Interface .................425 10.1 Overview ......................425 10.2 Main Menu......................426 10.2.1 System Menu....................426 10.2.1.1 View ARP Cache ................426 10.2.1.2 Viewing Inventory Information ............426...
Page 22 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.4 Managing BOOTP/DHCP Relay Agent..........552 10.2.3.5 Managing DNS Relay ..............554 10.2.3.6 Managing Routing Information Protocol (RIP) .........558 10.2.3.7 Managing Router Discovery ............565 10.2.3.8 Managing Route Table..............567 10.2.3.9 Managing VLAN Routing ..............572 10.2.3.10 Managing VRRP ................574 10.2.4 Security Menu....................579...
Page 23: Introduction
The Switch provides a management platform and uplink to backbone for a stacked group of eight JETNET 6524G Layer 3 Stackable switches in a ring or chain topology arrangement. Alternatively, the Switch can utilize up to twenty-four Gigabit Ethernet ports to function as a central distribution hub for other switches, switch groups, or routers.
Page 24: Front-Panel Components
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ‧ IP Routing support ‧ OSPF support ‧ RIP v1 and v2 support ‧ Router Discovery Protocol support ‧ VLAN routing support ‧ Virtual Router Redundancy Protocol (VRRP) support ‧ IP Multicast support ‧...
Page 25: Management Options
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Figure 1-2. Rear panel view of the switch The AC power connector is a standard three-pronged connector that supports the power cord. Plug the female connector of the provided power cord into this socket, and the male side of the cord into a power outlet.
Page 26: Snmp-Based Management
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 1.9 SNMP-Based Management You can manage the Switch with an SNMP-compatible console program. The Switch supports SNMP version 1.0, version 2.0, and version 3.0. The SNMP agent decodes the incoming SNMP messages and responds to requests with MIB objects stored in the database.
Page 27: Installation And Quick Startup
2 Installation and Quick Startup 2.1 Package Contents Before you begin installing the Switch, confirm that your package contains the following items: ‧ One JetNet 6524G Switch ‧ Mounting kit: 2 mounting brackets and screws ‧ One AC power cord ‧...
Page 28: Stacking The Switches
Layer 3 Stackable Switch 2.4 Stacking the Switches A total of 8 switches can be put into a single stack. Stacked JetNet 6524G Switches can be assigned a single IP address using the switch's management software. The stack can then be treated as a single manageable unit with one IP address.
Page 29: Quick Starting The Switch
Fig. 2-4: Cabling three JetNet 6524G switches. 2.5 Quick Starting the Switch 1. In-band connectivity allows access to the JetNet 6524G Switch locally or from a remote workstation. The device must be configured with IP information (IP address, subnet mask, and default gateway).
Page 30: Quick Start Up Physical Port Data
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Table 2-1. Quick Start up Software Version Information Command Details show hardware Allows the user to see the HW & SW version the device contains System Description - switch's model name show switch...
Page 31: Quick Start Up User Account Management
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 2.6.3 Quick Start up User Account Management Table 2-3. Quick Start up User Account Management Command Details show users Displays all users that are allowed to access the switch User Access Mode - Shows whether the...
Page 32 Korenix Technology Co., Ltd. Layer 3 Stackable Switch To view the network parameters the operator can access the device by the following three methods. • Simple Network Management Protocol - SNMP • Telnet • Web Browser Table 2-4. Quick Start up IP Address...
Page 33: Quick Start Up Uploading From Switch To Out-Of-Band Pc (Only Xmodem)
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Gateway Address range from 0.0.0.0 to 255.255.255.255 Displays login session information 2.6.5 Quick Start up Uploading from Switch to Out-of-Band PC (Only XMODEM) Table 2-5. Quick Start up Uploading from Switch to Out-of-Band PC (XMODEM)
Page 34: Quick Start Up Downloading From Tftp Server
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 2.6.7 Quick Start up Downloading from TFTP Server Before starting a TFTP server download, the operator must complete the Quick Start up for the IPAddress. Table 2-7 Quick Start up Downloading from TFTP Server...
Page 35 Korenix Technology Co., Ltd. Layer 3 Stackable Switch After assigning IP addresses to the Switch, you can connect devices to the Switch. To connect a device to an SFP transceiver port: 1. Use your cabling requirements to select an appropriate SFP transceiver type.
Page 36: Console And Telnet Administration Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 3 Console and Telnet Administration Interface This chapter discusses many of the features used to manage the Switch, and explains many concepts and important points regarding these features. Configuring the Switch to implement these concepts is discussed in detail in chapter 6.
Page 37: Set Up Your Switch Using Telnet Access
Korenix Technology Co., Ltd. Layer 3 Stackable Switch . Data width: 8 bits . Parity: none . Stop bits: 1 . Flow Control none A typical console connection is illustrated below: Figure 3-1: Console Setting Environment 3.3 Set Up your Switch Using Telnet Access Once you have set an IP address for your Switch, you can use a Telnet program (in a VT-100 compatible terminal mode) to access and control the Switch.
Page 38: Web-Based Management Interface
4 Web-Based Management Interface 4.1 Overview The Korenix JetNet 6524G provides a built-in browser interface that lets you configure and manage it remotely using a standard Web browser such as Microsoft Internet Explorer 5.0 or later or Netscape Navigator 6.0 or later. This interface also allows for system monitoring and management of the switch.
Page 39: Web-Based Management Menu
4. Type the default user name of admin and default of no password, or whatever password you have set up. Once you have entered your access point name, your Web browser automatically finds the JetNet 6524G Series Switch and display the home page, as shown below. 4.3 Web-Based Management Menu Figure 4-3: System Information page...
Page 40 Korenix Technology Co., Ltd. Layer 3 Stackable Switch This above page displays system information, such as: Click the icon then you can see the rear panel of the switch. • System Description • System Name • System Location • System Contact •...
Page 41 Korenix Technology Co., Ltd. Layer 3 Stackable Switch screen. You can click the ‘help’ or the question mark at the top right of each screen to view the help menu topics. The Secondary Menus are detailed below, with cross-references to the sections in this manual that contain the corresponding command descriptions.
Page 42 • Stack Port Counters — see “Stacking Commands” • Stack Port Counters Detail — see “Stacking Commands” System-Wide Popup Menus The JetNet 6524G Switch also provides several popup menus. _____________________________________________________________________________ Stackable Layer 3 Managed Ethernet Switch User Manual Page: 42/655...
Page 43 You can also access the main navigation menu by right clicking on the image of the switch and browsing to the menu you want to use. Port-Specific Popup Menus The JetNet 6524G also provides several popup menus for each port. _____________________________________________________________________________ Stackable Layer 3 Managed Ethernet Switch User Manual...
Page 44 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Figure 4-6: Switch popup menus You can access a port-specific popup menu by right clicking on the port in the image of the switch and browsing to the menu you want to use.
Page 45: Command Line Interface Structure And Mode-Based Cli
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 5 Command Line Interface Structure and Mode-based CLI The Command Line Interface (CLI) syntax, conventions, and terminology are described in this section. Each CLI command is illustrated using the structure outlined below.
Page 46 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Values ipaddr This parameter is a valid IP address, made up of four decimal bytes ranging from 0 to 255. The default for all IP parameters consists of zeros (that is, 0.0.0.0). The interface IP address of 0.0.0.0 is invalid.
Page 47 Korenix Technology Co., Ltd. Layer 3 Stackable Switch completion). The value 'Err' designates that the requested value was not internally accessible. This should never happen and indicates that there is a case in the software that is not handled correctly.
Page 48: Switching Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6 Switching Commands 6.1 System Information and Statistics commands 6.1.1 show arp This command displays connectivity between the switch and other devices. The Address Resolution Protocol (ARP) cache identifies the MAC addresses of the IP stations communicating with the switch.
Page 49: Show Eventlog
Korenix Technology Co., Ltd. Layer 3 Stackable Switch None Command Mode Privileged Exec Display Message Current Time displays system time 6.1.3 show eventlog This command displays the event log, which contains error messages from the system, in the Primary Management System or in the specified unit. The event log is not cleared on a system reset.
Page 50: Show Sysinfo
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command is used to display/capture the current setting of different protocol packages supported on switch. This command displays/captures only commands with settings/configurations with values that differ from the default value. The output is displayed in script format, which can be used to configure another switch with the same configuration.
Page 51: Show Hardware
Korenix Technology Co., Ltd. Layer 3 Stackable Switch System Contact: The text used to identify a contact person for this switch. May be up to 31 alphanumeric characters. The factory default is blank. System Object ID: The manufacturing ID. System Up Time: The time in days, hours and minutes since the last switch reboot.
Page 52: Show Loginsession
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Gigabit Ethernet Compliance Codes: Transceiver’s compliance codes. Vendor Name: The SFP transceiver vendor name shall be the full name of the corporation, a commonly accepted abbreviation of the name of the corporation, the SCSI company code for the corporation, or the stock exchange code for the corporation.
Page 53: Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.2.1 Interface 6.2.1.1 show interface status This command displays the Port monitoring information for the system. Syntax show interface status {<unit/slot/port> | all} <unit/slot/port> - is the desired interface number. all - This parameter displays information for all interfaces.
Page 54 Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays a summary of statistics for a specific interface or all interfaces. Syntax show interface counters {<unit/slot/port> | all} <unit/slot/port> - is the desired interface number. all - This command displays statistics information for all interfaces.
Page 55 Korenix Technology Co., Ltd. Layer 3 Stackable Switch segment. This command displays detailed statistics for a specific port or for all CPU traffic based upon the argument. Syntax show interface counters detailed {<unit/slot/port> | switchport} <unit/slot/port> - is the desired interface number.
Page 56 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Packets RX and TX 64 Octets: The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets). Packets RX and TX 65-127 Octets: The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
Page 57 Korenix Technology Co., Ltd. Layer 3 Stackable Switch bad FCS with a non-integral number of octets. FCS Errors: The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had a bad...
Page 58 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Multiple Collision Frames: A count of the number of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. Excessive Collisions: A count of frames for which transmission on a particular interface fails due to excessive collisions.
Page 59: Show Interface Switch
Korenix Technology Co., Ltd. Layer 3 Stackable Switch requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent. Multicast Packets Transmitted: The total number of packets that higher-level protocols requested be transmitted to a Multicast address, including those that were discarded or not sent.
Page 60: Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch packets and multicast packets) received by the processor. Broadcast Packets Received: The total number of packets received that were directed to the broadcast address. Note that this does not include multicast packets.
Page 61: Negotiate
Korenix Technology Co., Ltd. Layer 3 Stackable Switch speed-duplex {10 | 100} {full-duplex | half-duplex} 100 - 100BASE-T 10 - 10BASE-T full-duplex - Full duplex half-duplex - Half duplex Default Setting None Command Mode Interface Config This command is used to set the speed and duplex mode for all interfaces.
Page 62: Capabilities
Korenix Technology Co., Ltd. Layer 3 Stackable Switch negotiate no negotiate no - This command disables automatic negotiation on a port. Default Setting Enable Command Mode Interface Config This command enables automatic negotiation on all interfaces. The default value is enabled.
Page 63: Storm-Control Flowcontrol
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no capabilities {{10 | 100 } {full-duplex | half-duplex}} | {1000 full-duplex } 10 - 10BASE-T 100 - 100BASE-T 1000 - 1000BASE-T full-duplex - Full duplex half-duplex - Half duplex no - This command removes the advertised capability with using parameter.
Page 64: Shutdown
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Note: This command only applies to full-duplex mode ports. Syntax storm-control flowcontrol no storm-control flowcontrol no - This command disables 802.3x flow control for the switch. Default Setting Disabled Command Mode Global Config This command enables 802.3x flow control for the specific interface.
Page 65: L2 Mac Address And Multicast Forwarding Database Tables
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax shutdown no shutdown no - This command enables a port. Default Setting Enabled Command Mode Interface Config This command is used to disable all ports. Syntax shutdown all no shutdown all all - This command represents all ports.
Page 66: Show Mac-Address-Table Gmrp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Alternatively, the administrator can enter a MAC Address to display the table entry for the requested MAC address and all entries following the requested MAC address. Syntax show mac-addr-table [{<macaddr> |all}] <macaddr> - enter a MAC Address to display the table entry for the requested MAC address.
Page 67: Show Mac-Address-Table Igmpsnooping
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Multicast Forwarding Database (MFDB) table. Syntax show mac-address-table gmrp Default Setting None Command Mode Privileged Exec Display Message Mac Address: A unicast MAC address for which the switch has forwarding and/or filtering information.
Page 68: Show Mac-Address-Table Multicast
Korenix Technology Co., Ltd. Layer 3 Stackable Switch as 8 bytes. In an SVL system, the MAC address will be displayed as 6 bytes. Note: This software version only supports IVL systems. Type: This displays the type of the entry. Static entries are those that are configured by the end user.
Page 69: Show Mac-Address-Table Stats
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Forwarding Interfaces: The resultant forwarding list is derived from combining all the component’s forwarding interfaces and removing the interfaces that are listed as the static filtering interfaces. 6.2.2.5 show mac-address-table stats This command displays the MFDB statistics.
Page 70: Mac-Address-Table Aging-Time
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Display Message Address Aging Timout: This displays the total number of seconds for Forwarding Database table. 6.2.2.7 mac-address-table aging-time This command configures the forwarding database address aging timeout in seconds. Syntax mac-address-table aging-time <10-1000000>...
Page 71: Show Vlan Id
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Display Message VLAN ID: There is a VLAN Identifier (vlanid) associated with each VLAN. The range of the VLAN ID is 1 to 3965. VLAN Name: A string associated with this VLAN as a convenience. It can be up to 16 alphanumeric characters, including blanks.
Page 72: Show Protocol Group
Korenix Technology Co., Ltd. Layer 3 Stackable Switch GVRP. The port will not participate in this VLAN unless a join request is received on this port. This is equivalent to registration normal in the IEEE 802.1Q standard. Configured: Determines the configured degree of participation of this port in this VLAN. The permissible values are: Include: This port is always a member of this VLAN.
Page 73: Vlan Database
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays VLAN port information. Syntax show interface switchport {<unit/slot/port> | all} <unit/slot/port> - Interface number. all – Display the entire table. Default Setting None Command Mode Privileged Exec Display Message Unit/slot/port: Indicates by slot id and port number which port is controlled by the fields on this line.
Page 74: Vlan
Korenix Technology Co., Ltd. Layer 3 Stackable Switch None Command Mode Global Config 6.2.3.6 vlan This command creates a new VLAN and assigns it an ID. The ID is a valid VLAN identification number (ID 1 is reserved for the default VLAN). VLAN range is 2-3965.
Page 75: Vlan Makestatic
Korenix Technology Co., Ltd. Layer 3 Stackable Switch VLAN identification number. ID range is 1-3965. Default Setting The name for VLAN ID 1 is always Default. The name for other VLANs is defaulted to a blank string. Command Mode VLAN database 6.2.3.8...
Page 76: Switchport Acceptable-Frame-Type
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <group-name> - a VLAN Group Name (a character string of 1 to 16 characters). no - This command removes the <vlanid> from this protocol-based VLAN group that is identified by this <group-name>.
Page 77: Switchport Ingress-Filtering
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax switchport acceptable-frame-type all {tagged | all} no switchport acceptable-frame-type all {tagged | all} tagged - VLAN only mode. all – One is for Admit all mode. The other one is for all interfaces.
Page 78: Switchport Native Vlan
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command enables ingress filtering for all ports. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving interface are admitted and forwarded to ports that are members of that VLAN.
Page 79: Switchport Allowed Vlan
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command changes the VLAN ID for all interfaces. Syntax switchport native vlan all <vlanid> <vlanid> - VLAN ID (Range: 1 –3965). all - All interfaces. no - This command sets the VLAN ID for all interfaces to 1.
Page 80: Switchport Tagging
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command configures the degree of participation for all interfaces in a VLAN. The ID is a valid VLAN identification number. Syntax switchport allowed vlan {add {tagged | untagged} | remove} all <vlanid>...
Page 81: Switchport Priority
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Disabled Command Mode Interface Config This command configures the tagging behavior for all interfaces in a VLAN to be enabled. If tagging is enabled, traffic is transmitted as tagged frames. If tagging is disabled, traffic is transmitted as untagged frames.
Page 82: Switchport Protocol Group
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Command Mode Interface Config This command configures the port priority assigned for untagged packets for all ports presently plugged into the device. Any subsequent per port configuration will override this configuration setting.
Page 83 Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - This command removes the interface from this protocol-based VLAN group that is identified by this <group-name>. Default Setting None Command Mode Interface Config This command adds a protocol-based VLAN group to the system. The <group-name> is a character string of 1 to 16 characters.
Page 84 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax switchport protocol group all <group-name> no switchport protocol group all <group-name> <group-name> - a VLAN Group Name (a character string of 1 to 16 characters). all - All interfaces. no - This command removes all interfaces from this protocol-based VLAN group that is identified by this <group-name>.
Page 85: Switchport Forbidden Vlan
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 6.2.3.17 switchport forbidden vlan This command used to configure forbidden VLANs. Syntax switchport forbidden vlan {add | remove} <vlanid> no switchport forbidden <vlanid> - VLAN ID (Range: 1 –3965).
Page 86: Show Gvrp Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Privileged Exec Display Message GMRP Admin Mode: This displays the administrative mode of GARP Multicast Registration Protocol (GMRP) for the system. GVRP Admin Mode: This displays the administrative mode of GARP VLAN Registration Protocol (GVRP) for the system.
Page 87: Show Gmrp Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch per-Port, per-GARP participant basis. The Leave All Period Timer is set to a random value in the range of LeaveAll- Time to 1.5*LeaveAllTime. Permissible values are 200 to 6000 centiseconds (2 to 60 seconds). The factory default is 1000 centiseconds (10 seconds). The finest granularity of specification is 1 centisecond (0.01 seconds).
Page 88: Show Garp Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch the range of LeaveAll- Time to 1.5*LeaveAllTime. Permissible values are 200 to 6000 centiseconds (2 to 60 seconds). The factory default is 1000 centiseconds (10 seconds). The finest granularity of specification is 1 centisecond (0.01 seconds).
Page 89: Bridge-Ext Gmrp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch bridge-ext gvrp no bridge-ext gvrp no - This command disables GVRP. Default Setting Disabled Command Mode Global Config 6.2.4.6 bridge-ext gmrp This command enables GARP Multicast Registration Protocol (GMRP) on the system. The default value is disabled.
Page 90: Switchport Gmrp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch switchport gvrp no switchport gvrp no - This command disables GVRP (GARP VLAN Registration Protocol) for a specific port. If GVRP is disabled, Join Time, Leave Time, and Leave All Time have no effect.
Page 91 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax switchport gmrp no switchport gmrp no - This command disables GMRP Multicast Registration Protocol on a selected interface. If an interface which has GMRP enabled is enabled for routing or is enlisted as a member of a port-channel (LAG), GMRP functionality will be disabled on that interface.
Page 92: Garp Timer
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.2.4.9 garp timer This command sets the GVRP join time per port and per GARP. Join time is the interval between the transmission of GARP Protocol Data Units (PDUs) registering (or re-registering) membership for a VLAN or multicast group.
Page 93 Korenix Technology Co., Ltd. Layer 3 Stackable Switch all - All interfaces. no - This command sets the GVRP join time for all ports and per GARP to 20 centiseconds (0.2 seconds). This command has an effect only when GVRP and GMRP are enabled.
Page 94 Korenix Technology Co., Ltd. Layer 3 Stackable Switch attribute in order to maintain uninterrupted service. The time is from 20 to 600 (centiseconds). Note: This command has an effect only when GVRP and GMRP are enabled. Syntax garp timer leave all < 20-600 >...
Page 95: Igmp Snooping
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting 1000 centiseconds (10 seconds) Command Mode Interface Config This command sets how frequently Leave All PDUs are generated for all ports. A Leave All PDU indicates that all registrations will be unregistered. Participants would need to rejoin in order to maintain registration.
Page 96 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.2.5.1.1. show ip igmp snooping This command displays IGMP Snooping information. Configured information is displayed whether or not IGMP Snooping is enabled. Status information is only displayed when IGMP Snooping is enabled.
Page 97 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Privileged Exec Display Message VLAN ID: This displays VLAN ID value. Unit/Slot/Port: The interface number. Multicast Router Attached: This displays if the interface is enabled as a multicast router port. 6.2.5.1.3. show ip igmp snooping multicast This command displays the known multicast address.
Page 98: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show ip igmp snooping <1-3965> <1-3965> - VLAN ID (Range: 1 – 3965). Default Setting None Command Mode Privileged Exec Display Message Vlan ID This is the list of VLANS on which IGMP Snooping is enabled.
Page 99 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Disabled Command Mode Global Config 6.2.5.2.2. ip igmp snooping groupmembershipinterval This command sets the IGMP Group Membership Interval time on the system. The Group Membership Interval time is the amount of time in seconds that a switch will wait for a report from a particular group on a particular interface before deleting the interface from the entry.
Page 100 Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - This command disables IGMP Snooping on a selected interface. Default Setting Disabled Command Mode Interface Config This command enables IGMP Snooping on all interfaces. If an interface which has IGMP Snooping enabled is enabled for routing or is enlisted as a member of a port-channel (LAG), IGMP Snooping functionality will be disabled on that interface.
Page 101 Korenix Technology Co., Ltd. Layer 3 Stackable Switch no ip igmp snooping mcrtrexpiretime <0-3600> - Expiration time (Range: 0 – 3600). no - This command sets the Multicast Router Present Expiration time on the system to 0. A value of 0 indicates an infinite timeout, that is no expiration.
Page 102 Korenix Technology Co., Ltd. Layer 3 Stackable Switch directed to that group. Also, fast-leave processing is supported only with IGMP version 2 hosts. Syntax ip igmp snooping immediate-leave no ip igmp snooping immediate-leave no - This command disables IGMP Snooping fast-leave admin mode.
Page 103 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Interface Config. This command configures the VLAN ID(<vlanId>) that has the multicast router mode enabled. Syntax ‧ip igmp snooping mrouter <vlanId> ‧no set igmp snooping mrouter <vlanId> <vlanId> - VLAN ID. no - This command disables the status of the interface as a statically configured multicast router interface.
Page 104 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Global Config Command Usage The maximum number of static router ports that can be configured is 64. 6.2.5.2.9. set igmp This command enables IGMP snooping on a particular VLAN, and in turn enabling IGMP snooping on all interfaces participating in this VLAN.
Page 105 Korenix Technology Co., Ltd. Layer 3 Stackable Switch no set igmp groupmembershipinterval <1-3965> <1-3965> - VLAN ID (Range: 1 – 3965). <2-3600> - The range of group membership interval time is 2 to 3600 seconds. no - This command sets the IGMP Group Membership Interval time on a particular VLAN to the default value.
Page 106 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.2.5.2.12. set igmp mcrtexpiretime This command sets the Multicast Router Present Expiration time on a particular VLAN. This is the amount of time in seconds that a switch will wait for a query to be received on an interface, which is participating in the VLAN, before the interface is removed from the list of interfaces with multicast routers attached.
Page 107: Port Channel
Korenix Technology Co., Ltd. Layer 3 Stackable Switch set igmp fast-leave <1-3965> no set igmp fast-leave <1-3965> <1-3965> - VLAN ID (Range: 1 – 3965). no - This command disables IGMP Snooping fast-leave admin mode on a selected VLAN. Default Setting...
Page 108 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Port-Channel Name: This field displays the name of the port-channel. Link State: This field indicates whether the link is up or down. Mbr Ports: This field lists the ports that are members of this port-channel, in unit/slot/port notation.
Page 109: Port-Channel
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.2.6.2 port-channel This command configures a new port-channel (LAG) and generates a logical slot and port number for it. Display this number using the show port-channel. Note: Before including a port in a port-channel, set the port physical mode. See speed command.
Page 110: Port-Channel Staticcapability
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Enabled Command Mode Global Config 6.2.6.4 port-channel staticcapability This command enables the support of port-channels (static link aggregations - LAGs) on the device. By default, the static capability for all port-channels is disabled.
Page 111: Port-Channel Name
Korenix Technology Co., Ltd. Layer 3 Stackable Switch all - all Port-Channel interfaces. no - This command disables link trap notifications for the port-channel (LAG). The interface is a logical slot and port for a configured port-channel. The option all sets every configured port-channel with the same administrative mode setting.
Page 112: Lacp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax adminmode no adminmode no - This command disables a configured port-channel (LAG). Default Setting Enabled Command Mode Interface Config 6.2.6.8 lacp This command enables Link Aggregation Control Protocol (LACP) on a port.
Page 113: Channel-Group
Korenix Technology Co., Ltd. Layer 3 Stackable Switch lacp all no lacp all all - All interfaces. no - This command disables Link Aggregation Control Protocol (LACP) on all ports. Default Setting Enabled Command Mode Global Config 6.2.6.9 channel-group This command adds one port to the port-channel (LAG). The first interface is a logical slot and port number of a configured port-channel.
Page 114: Storm Control
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command deletes the port from the port-channel (LAG). The interface is a logical slot and port number of a configured port-channel. Syntax delete-channel-group <logical unit/slot/port> <logical unit/slot/port> - Port-Channel Interface number.
Page 115 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show storm-control broadcast Default Setting None Command Mode Privileged Exec Display Message Intf: Displays interface number. Mode: Displays status of storm control broadcast. Level: Displays level for storm control broadcast. Rate: Displays rate for storm control broadcast.
Page 116: Storm-Control Broadcast
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command is used to display unicast storm control information Syntax show storm-control unicast Default Setting None Command Mode Privileged Exec Display Message Intf: Displays interface number. Mode: Displays status of storm control unicast.
Page 117: Storm-Control Multicast
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Disabled Command Mode Interface Config This command enables broadcast storm recovery mode on all interfaces. Syntax storm-control broadcast no storm-control broadcast no - This command disables broadcast storm recovery mode on all interfaces.
Page 118: Storm-Control Unicast
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Interface Config This command enables multicast storm recovery mode on all interfaces. Syntax storm-control multicast no storm-control multicast no - This command disables multicast storm recovery mode on all interfaces. Default Setting...
Page 119: Switchport Broadcast Packet-Rate
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command enables unicast storm recovery mode on all interfaces. Syntax storm-control unicast no storm-control unicast no - This command disables unicast storm recovery mode on all interfaces. Default Setting None Command Mode Global Config 6.2.7.5...
Page 120: Switchport Multicast Packet-Rate
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command will protect your network from broadcast storms by setting a threshold level for broadcast traffic on all ports. Syntax switchport broadcast all packet-rate {1 | 2 | 3 | 4} 1 - Threshold level represents 64 pps (packet per second).
Page 121: Switchport Unicast Packet-Rate
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command will protect your network from multicast storms by setting a threshold level for multicast traffic on all ports. Syntax switchport multicast all packet-rate {1 | 2 | 3 | 4} 1 - Threshold level represents 64 pps (packet per second).
Page 122: L2 Priority
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Interface Config This command will protect your network from unicast storms by setting a threshold level for unicast traffic on all ports. Syntax switchport unicast all packet-rate {1 | 2 | 3 | 4} 1 - Threshold level represents 64 pps (packet per second).
Page 123: Queue Cos-Map
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Privileged Exec Display Message User Priority: Displays the 802.1p priority to be mapped. Traffic Class: Displays internal traffic class to map the corresponding 802.1p priority. 6.2.8.2 queue cos-map This command is used to assign class of service (CoS) value to the CoS priority queue.
Page 124: Port-Monitor Session
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays the Port monitoring information for the specified session. Syntax show port-monitor session <SessionNum> Default Setting None Command Mode Privileged Exec Display Message Session ID: indicates the session ID. Admin Mode: indicates whether the Port Monitoring feature is enabled or disabled. The possible values are enabled and disabled.
Page 125: Port-Monitor Session Mode
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command removes all configured probe ports and mirrored port. Syntax no port-monitor Default Setting None Command Mode Global Config 6.2.9.3 port-monitor session mode This command configures the administration mode of port-monitoring function for a monitor session.
Page 126: Show Ip Filter
Korenix Technology Co., Ltd. Layer 3 Stackable Switch The network interface is the logical interface used for in-band connectivity with the switch via any of the switch's front panel ports. The configuration parameters associated with the switch's network interface do not affect the configuration of the front panel ports through which traffic is switched or routed.
Page 127: Show Ip Ipv6
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Privileged Exec Display Message Index: The index of stations. IP Address: The IP address of stations that are allowed to make configuration changes to the Switch. 6.3.1.3 show ip ipv6 This command displays the IPv6 forwarding status of all ports.
Page 128: Interface Vlan
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting 1518 Command Mode Interface Config 6.3.1.5 interface vlan This command is used to enter Interface-vlan configuration mode. Syntax interface vlan <vlanid> <vlanid> - VLAN ID (Range: 1 - 3965). Default Setting...
Page 129: Ip Default-Gateway
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting IP address: 0.0.0.0 Subnet Mask: 0.0.0.0 Command Mode Interface-Vlan Config Command Usage Once the IP address is set, the VLAN ID’s value will be assigned to management VLAN. 6.3.1.7 ip default-gateway This command sets the IP Address of the default gateway.
Page 130: Ip Filter
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ip address protocol {bootp | dhcp | none} <bootp> - Obtains IP address from BOOTP. <dhcp> - Obtains IP address from DHCP. <none> - Obtains IP address by setting configuration. Default Setting...
Page 131: Ip Ipv6
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <ipaddr> - Configure a IP address to be a filter. No - Remove this filter IP address. Default Setting None Command Mode Global Config 6.3.1.10 ip ipv6 This command is used to enable the Ipv6 function on specific interface.
Page 132: Serial Interface Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - disable IPv6. Default Setting Enabled Command Mode Global Config 6.3.2 Serial Interface Commands 6.3.2.1 show line console This command displays serial communication settings for the switch. Syntax show line console...
Page 133: Line Console
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.2.2 line console This command is used to enter Line configuration mode Syntax line console Default Setting None Command Mode Global Config 6.3.2.3 baudrate This command specifies the communication rate of the terminal interface. The supported rates are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200.
Page 134: Password-Threshold
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax exec-timeout <0-160> <0-160> - max connect time (Range: 0 -160). no - This command sets the maximum connect time (in minutes) without console activity to Default Setting Command Mode Line Config 6.3.2.5...
Page 135: Telnet Session Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax silent-time <0-65535> <0-65535> - silent time (Range: 0 - 65535) in seconds. no - This command sets the maximum value to the default. Default Setting Command Mode Line Config 6.3.3 Telnet Session Commands 6.3.3.1...
Page 136: Show Line Vty
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.3.2 show line vty This command displays telnet settings. Syntax show line vty Default Setting None Command Mode Privileged Exec Display Message Remote Connection Login Timeout (minutes): This object indicates the number of minutes a remote connection session is allowed to remain inactive before being logged off.
Page 137: Exec-Timeout
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.3.4 exec-timeout This command sets the remote connection session timeout value, in minutes. A session is active as long as the session has been idle for the value set. A value of 0 indicates that a session remains active indefinitely.
Page 138: Maxsessions
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Command Mode Telnet Config 6.3.3.6 maxsessions This command specifies the maximum number of remote connection sessions that can be established. A value of 0 indicates that no remote connection can be established. The range is 0 to 5.
Page 139: Telnet Sessions
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - This command disables telnet sessions. If sessions are disabled, no new telnet sessions are established. Default Setting Enabled Command Mode Telnet Config 6.3.3.8 telnet sessions This command regulates new outbound telnet connections. If enabled, new outbound telnet sessions can be established until it reaches the maximum number of simultaneous outbound telnet sessions allowed.
Page 140: Telnet Exec-Timeout
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax telnet maxsessions <0-5> no maxsessions <0-5> - max sessions (Range: 0 - 5). no - This command sets the maximum value to be 5. Default Setting Command Mode Global Config 6.3.3.10 telnet exec-timeout This command sets the outbound telnet session timeout value in minute.
Page 141: Show Telnet
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.3.11 show telnet This command displays the current outbound telnet settings. Syntax show telnet Default Setting None Command Mode User Exec, Privileged Exec Display Message Outbound Telnet Login Timeout (in minutes) Indicates the number of minutes an outbound telnet session is allowed to remain inactive before being logged off.
Page 142: Show Trapflags
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show snmp Default Setting None Command Mode Privileged Exec Display Message SNMP Community Name: The community string to which this entry grants access. A valid entry is a case-sensitive alphanumeric string of up to 16 characters. Each row of this table must contain a unique community name.
Page 143: Snmp-Server Sysname
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Privileged Exec Display Message Authentication Flag: May be enabled or disabled. The factory default is enabled. Indicates whether authentication failure traps will be sent. Link Up/Down Flag: May be enabled or disabled. The factory default is enabled. Indicates whether link status traps will be sent.
Page 144: Snmp-Server Contact
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax snmp-server location <loc> <loc> - range is from 1 to 31 alphanumeric characters. Default Setting None Command Mode Global Config 6.3.4.5 snmp-server contact This command sets the organization responsible for the network. The range for contact is from 1 to 31 alphanumeric characters.
Page 145 Korenix Technology Co., Ltd. Layer 3 Stackable Switch entries are ignored. Syntax snmp-server community <name> no snmp-server community <name> <name> - community name (up to 16 case-sensitive characters). no - This command removes this community name from the table. The name is the community name to be deleted.
Page 146 Korenix Technology Co., Ltd. Layer 3 Stackable Switch The default public and private communities are enabled by default. The four undefined communities are disabled by default. Command Mode Global Config This command sets a client IP mask for an SNMP community. The address is the associated...
Page 147: Snmp-Server Host
Korenix Technology Co., Ltd. Layer 3 Stackable Switch snmp-server community {ro | rw} <name> <name> - community name. <ro> - access mode is read-only. <rw> - access mode is read/write. Default Setting None Command Mode Global Config 6.3.4.7 snmp-server host This command sets a client IP address for an SNMP community.
Page 148: Snmp-Server Enable Traps
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.4.8 snmp-server enable traps This command enables the Authentication trap. Syntax snmp-server enable traps authentication no snmp-server enable traps authentication no - This command disables the Authentication trap. Default Setting Enabled Command Mode Global Config This command enables the DVMRP trap.
Page 149 Korenix Technology Co., Ltd. Layer 3 Stackable Switch snmp-server enable traps linkmode no snmp-server enable traps linkmode no - This command disables Link Up/Down traps for the entire switch. Default Setting Enabled Command Mode Global Config This command enables Multiple User traps. When the traps are enabled, a Multiple User Trap is sent when a user logs in to the terminal interface (EIA 232 or telnet) and there is an existing terminal interface session.
Page 150 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Enabled Command Mode Global Config This command enables PIM traps. Syntax snmp-server enable traps pim no snmp-server enable traps pim no - This command disables PIM trap. Default Setting Enabled...
Page 151: Snmp Trap Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.5 SNMP Trap Commands 6.3.5.1 show snmptrap This command displays SNMP trap receivers. Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network.
Page 152 Korenix Technology Co., Ltd. Layer 3 Stackable Switch snmp trap link-status no snmp trap link-status no - This command disables link status traps by interface. Note: This command is valid only when the Link Up/Down Flag is enabled. (See ‘snmpserver enable traps linkmode’ command.)
Page 153: Snmptrap
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.5.3 snmptrap <name> <ipaddr> This command adds an SNMP trap name. The maximum length of the name is 16 case-sensitive alphanumeric characters. Syntax snmptrap <name> <ipaddr> no snmptrap <name> <ipaddr> <name> - SNMP trap name (Range: up to 16 case-sensitive alphanumeric characters).

Page 154: Snmptrap Mode
Korenix Technology Co., Ltd. Layer 3 Stackable Switch None Command Mode Global Config 6.3.5.5 snmptrap mode This command activates or deactivates an SNMP trap. Enabled trap receivers are active (able to receive traps). Disabled trap receivers are inactive (not able to receive traps).
Page 155: Ip Javamode
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message HTTP Mode (Unsecure): This field indicates whether the HTTP mode is enabled or disabled. HTTP Port: This field specifies the port configured for HTTP.
Page 156: Ip Http Server
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax ip http port <1-65535> no ip http port <1-65535> - HTTP Port value. no - This command is used to reset the http port to the default value. Default Setting Command Mode Global Config 6.3.6.4...
Page 157: Ip Http Secure-Port
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.3.6.5 ip http secure-port This command is used to set the SSLT port where port can be 1-65535 and the default is port 443. Syntax ip http secure-port <portid> no ip http secure-port <portid>...
Page 158: Secure Shell (Ssh) Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command is used to set protocol levels (versions). The protocol level can be set to TLS1, SSL3 or to both TLS1 and SSL3. Syntax ip http secure-protocol <protocollevel1> [protocollevel2] no ip http secure-protocol <protocollevel1> [protocollevel2] <protocollevel1 - 2>...
Page 159: Ip Ssh
Korenix Technology Co., Ltd. Layer 3 Stackable Switch connections. Max SSH Sessions Allowed: The maximum number of inbound SSH sessions allowed on the switch. SSH Timeout: This field is the inactive timeout value for incoming SSH sessions to the switch.
Page 160: Ip Ssh Maxsessions
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 6.3.7.4 ip ssh maxsessions This command specifies the maximum number of SSH connection sessions that can be established. A value of 0 indicates that no ssh connection can be established. The range is 0 to Syntax ip ssh maxsessions <0-5>...
Page 161: Dhcp Client Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ip ssh timeout <1-160> no ip ssh timeout <1-160> - timeout interval in seconds. no - This command sets the SSH connection session timeout value, in minutes, to the default. Changing the timeout value for active sessions does not become effective until the session is reaccessed.
Page 162: Dhcp Relay Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax ip dhcp client-identifier {text <text> | hex <hex>} no ip dhcp client-identifier <text> - A text string. (Range: 1-15 characters). <hex> - The hexadecimal value (00:00:00:00:00:00). no - This command is used to restore to default value.
Page 163: Bootpdhcprelay Maxhopcount
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Admin Mode - Administrative mode of the relay. When you select 'enable' BOOTP/DHCP requests will be forwarded to the IP address you entered in the 'Server IP address' field. Server IP Address - IP address of the BOOTP/DHCP server or the IP address of the next BOOTP/DHCP Relay Agent.
Page 164: Spanning Tree Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command is used to configure the server IP Address for BootP/DHCP Relay on the system. Syntax bootpdhcprelay serverip <ipaddr> no bootpdhcprelay serverip <ipaddr> - A server IP address. no - This command is used to reset to the default value.
Page 165: Show Spanning-Tree Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message Bridge Priority: Configured value. Bridge Identifier: The MAC Address for the Bridge from which the Bridge Identifiers used by the Spanning Tree Algorithm and Protocol.
Page 166: Show Spanning-Tree Vlan
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message Port Mode: The administration mode of spanning tree. Port Up Time Since Counters Last Cleared: Time since the port was reset, displayed in days, hours, minutes, and seconds.
Page 167: Show Spanning-Tree Mst
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.4.1.4 show spanning-tree mst This command displays settings and parameters for the specified multiple spanning tree instance. The instance <0-4094> is a number that corresponds to the desired existing multiple spanning tree instance ID. The following details are displayed.
Page 168 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message MST Instance ID List: List of multiple spanning trees IDs currently configured. For each MSTID: The multiple spanning tree instance ID. Associated FIDs: List of forwarding database identifiers associated with this instance.
Page 169 Korenix Technology Co., Ltd. Layer 3 Stackable Switch LAN. If 0 (defined as the default CIST ID) is passed as the <0-4094>, then this command displays the settings and parameters for a specific switch port within the common and internal spanning tree.
Page 170: Show Spanning-Tree Summary
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <unit/slot/port> - is the desired interface number. all - All interfaces. Default Setting None Command Mode Privileged Exec Display Message MST Instance ID: The MST instance associated with this port. Interface: The interface being displayed.
Page 171: Show Spanning-Tree Brief
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.4.1.6 show spanning-tree brief This command displays spanning tree settings for the bridge. In this case, the following details are displayed. Syntax show spanning-tree brief Default Setting None Command Mode Privileged Exec Display Message Bridge Priority: Configured value.
Page 172: Spanning-Tree Protocol-Migration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 6.4.2.2 spanning-tree protocol-migration This command enables BPDU migration check on a given interface. The all option enables BPDU migration check on all interfaces. Syntax spanning-tree protocol-migration {<unit/slot/port> | all} no spanning-tree protocol-migration {<unit/slot/port>...
Page 173: Spanning-Tree Mode
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - This command resets the Configuration Identifier Name to its default. Default Setting The base MAC address displayed using hexadecimal notation as specified in IEEE 802 standard. Command Mode Global Config This command sets the Configuration Identifier Revision Level for use in identifying the configuration that this switch is currently using.
Page 174: Spanning-Tree Forward-Time
Korenix Technology Co., Ltd. Layer 3 Stackable Switch mstp - MST BPDUs are transmitted (IEEE 802.1s functionality supported) Syntax spanning-tree mode {stp | rstp | mstp} no spanning-tree mode no - This command sets the Force Protocol Version parameter to the default value, that is, mstp.
Page 175: Spanning-Tree Hello-Time
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.4.2.6 spanning-tree hello-time This command sets the Hello Time parameter to a new value for the common and internal spanning tree. The hellotime value is in whole seconds within a range of 1 to 10 with the value being less than or equal to "(Bridge Max Age / 2) - 1".
Page 176: Spanning-Tree Max-Hops
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 6.4.2.8 spanning-tree max-hops This command sets the MSTP Max Hops parameter to a new value for the common and internal spanning tree. The max-hops value is in a range of 1 to 127.
Page 177 Korenix Technology Co., Ltd. Layer 3 Stackable Switch <1-4094> - multiple spanning tree instance ID. no - This command removes a multiple spanning tree instance from the switch and reallocates all VLANs allocated to the deleted instance to the common and internal spanning tree.
Page 178 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Global Config This command adds an association between a multiple spanning tree instance and a VLAN. The VLAN will no longer be associated with the common and internal spanning tree. The instance <0-4094> is a number that corresponds to the desired existing multiple spanning tree instance.
Page 179 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax spanning-tree mst <0-4094> cost {<1-200000000> | auto} no spanning-tree mst <0-4094> cost <0-4094> - multiple spanning tree instance ID. no - This command sets the Path Cost or Port Priority for this port within the multiple spanning tree instance or in the common and internal spanning tree to the respective default values.
Page 180: Spanning-Tree Port Mode
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <0-4094> - multiple spanning tree instance ID. no - This command sets the Path Cost or Port Priority for this port within the multiple spanning tree instance or in the common and internal spanning tree to the respective default values.
Page 181: Spanning-Tree Edgeport
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax spanning-tree port mode all no spanning-tree port mode all all - All interfaces. no - This command sets the Administrative Switch Port State for all ports to disabled. Default Setting Disabled...
Page 182: Show Logging
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.5.1.1 show logging This command displays logging. Syntax show logging Default Setting None Command Mode Privileged Exec Display Message Logging Client Local Port The port on the collector/relay to which syslog messages are sent CLI Command Logging The mode for CLI command logging.
Page 183: Show Logging Traplog
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Display Message Message: The message that has been logged. Note: Message log information is not retained across a switch reset. 6.5.3 show logging traplog This command displays the trap log maintained by the switch.
Page 184: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message Index (used for deleting) IP Address IP Address of the configured server. Severity The minimum severity to log to the specified address. Port Server Port Number.This is the port on the local host from which syslog messages are sent.
Page 185: Logging Console
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax logging buffered wrap no logging buffered wrap no - This command disables wrapping of in-memory logging when full capacity reached. Default Setting None Command Mode Privileged Exec 6.5.4.2 logging console This command enables logging to the console.
Page 186: Logging Host
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.5.4.3 logging host This command enables logging to a host where up to eight hosts can be configured. Syntax logging host <hostaddress> [ <port>] [[<severitylevel> | <0-7>]] <hostaddress> - IP address of the log server.
Page 187: Logging Syslog
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax logging host reconfigure <hostindex> <hostaddress> < hostindex > - Index of the log server. <hostaddress> - New IP address of the log server. Default Setting None Command Mode Privileged Exec 6.5.4.4 logging syslog This command enables syslog logging.
Page 188: Clear Logging Buffered
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax logging syslog port <portid> no logging syslog port no - Resets the local logging port to the default. Default Setting None Command Mode Privileged Exec 6.5.4.5 clear logging buffered This command clears all in-memory log.
Page 189: Script Delete
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command applies the commands in the configuration script to the switch. The apply command backs up the running configuration and then starts applying the commands in the script file. Application of the commands stops at the first failure of a command.
Page 190: Script Show
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command lists all scripts present on the switch as well as the total number of files present. Syntax script list Default Setting None Command Mode Privileged Exec 6.6.4 script show This command displays the content of a script file.
Page 191: Show Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.7.1 Show Commands 6.7.1.1 show users This command displays the configured user names and their settings. This command is only available for users with readwrite privileges. The SNMPv3 fields will only be displayed if SNMP is available on the system.
Page 192: Username Snmpv3 Authentication
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command changes the password of an existing operator. User password should not be more than eight characters in length. If a user is authorized for authentication or encryption is enabled, the password must be eight alphanumeric characters in length. The username and password are not case-sensitive.
Page 193: Username Snmpv3 Encryption
Korenix Technology Co., Ltd. Layer 3 Stackable Switch md5 - md5 authentication method. sha - sha authentication method. none - no use authentication method. no - This command sets the authentication protocol to be used for the specified login user to none.
Page 194: Security Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.8 Security Commands 6.8.1 Show Commands 6.8.1.1 show users authentication This command displays all users and all authentication login information. It also displays the authentication login list assigned to the default user.
Page 195: Show Authentication Users
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Authentication Login List: This displays the authentication login listname. Method 1: This displays the first method in the specified authentication login list, if any. Method 2: This displays the second method in the specified authentication login list, if any.
Page 196: Show Dot1X Detail
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Privileged Exec Display Message Administrative mode: Indicates whether authentication control on the switch is enabled or disabled. 6.8.1.5 show dot1x detail This command is used to show a summary of the global dot1x configuration and the detailed dot1x configuration for a specified port.
Page 197: Show Dot1X Statistics
Korenix Technology Co., Ltd. Layer 3 Stackable Switch authentication server. The value is expressed in seconds and will be in the range of 1 to 65535. Maximum Requests: The maximum number of times the authenticator state machine on this port will retransmit an EAPOL EAP Request/Identity before timing out the supplicant.
Page 198: Show Dot1X Summary
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Last EAPOL Frame Source: The source MAC address carried in the most recently received EAPOL frame. EAP Response/Id Frames Received: The number of EAP response/identity frames that have been received by this authenticator.
Page 199: Show Dot1X Users
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.8.1.8 show dot1x users This command displays 802.1x port security user information for locally configured users. Syntax show dot1x users <unit/slot/port> <unit/slot/port> - is the desired interface number. Default Setting None Command Mode...
Page 200: Show Radius
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.8.1.10 show radius This command is used to display the various RADIUS configuration items for the switch. Syntax show radius Default Setting None Command Mode Privileged Exec Display Message Current Server IP Address: Indicates the configured server currently in use for...
Page 201: Show Radius Statistics
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Display Message If the optional token 'statistics <ipaddr>' is not included, then only the accounting mode and the RADIUS accounting server details are displayed. RADIUS Accounting Mode: Enabled or disabled IP Address: The configured IP address of the RADIUS accounting server...
Page 202: Show Tacacs
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <ipaddr> - is an IP Address. Default Setting None Command Mode Privileged Exec Display Message If an IP address is not specified then only the Invalid Server Addresses field is displayed. Otherwise, the other listed fields are displayed.
Page 203: Show Port-Security
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show tacacs Default Setting None Command Mode Privileged Exec Display Message Admin Mode: Displays TACACS administration mode. Server 1 Port: TACACS packet port number Server 1 Key: Secret Key between TACACS server and client...
Page 204 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show port-security Default Setting None Command Mode Privileged Exec Display Message Port Security Administration Mode: Port lock mode for the entire system. This command shows the port-security settings for a particular interface or all interfaces.
Page 205 Korenix Technology Co., Ltd. Layer 3 Stackable Switch None Command Mode Privileged Exec Display Message MAC address Dynamically locked MAC address. This command shows the statically locked MAC addresses for port. Syntax show port-security static <unit/slot/port> Default Setting None Command Mode...
Page 206: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.8.2 Configuration Commands 6.8.2.1 authentication login This command creates an authentication login list. The <listname> is up to 15 alphanumeric characters and is not case sensitive. Up to 10 authentication login lists can be configured on the switch.
Page 207: Username Defaultlogin
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 6.8.2.2 username defaultlogin This command assigns the authentication login list to use for non-configured users when attempting to log in to the system. This setting is overridden by the authentication login list assigned to a specific user if the user is configured locally.
Page 208: Dot1X Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <listname> - an authentication login list. Default Setting None Command Mode Global Config 6.8.3 Dot1x Configuration Commands 6.8.3.1 dot1x initialize This command begins the initialization sequence on the specified port. This command is only valid if the control mode for the specified port is 'auto'.
Page 209: Dot1X Login
Korenix Technology Co., Ltd. Layer 3 Stackable Switch dot1x defaultl-login <listname> <listname> - an authentication login list. Default Setting None Command Mode Global Config 6.8.3.3 dot1x login This command assigns the specified authentication login list to the specified user for 802.1x port security.
Page 210: Dot1X User
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax dot1x system-auth-control no dot1x system-auth-control no - This command is used to disable the dot1x authentication support on the switch. Default Setting Disabled Command Mode Global Config 6.8.3.5 dot1x user This command adds the specified user to the list of users with access to the specified port or all ports.
Page 211 Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command sets the authentication mode to be used on all ports. The control mode may be one of the following. force-unauthorized: The authenticator PAE unconditionally sets the controlled port to unauthorized.
Page 212: Dot1X Max-Req
Korenix Technology Co., Ltd. Layer 3 Stackable Switch auto Command Mode Interface Config 6.8.3.7 dot1x max-req This command sets the maximum number of times the authenticator state machine on this port will transmit an EAPOL EAP Request/Identity frame before timing out the supplicant. The <1-10>...
Page 213: Dot1X Re-Reauthenticate
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Disabled Command Mode Interface Config 6.8.3.9 dot1x re-reauthenticate This command begins the re-authentication sequence on the specified port. This command is only valid if the control mode for the specified port is 'auto'. If the control mode is not 'auto' an error will be returned.
Page 214: Radius Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch tx-period: Sets the value, in seconds, of the timer used by the authenticator state machine on this port to determine when to send an EAPOL EAP Request/Identity frame to the supplicant. The quiet-period must be a value in the range 1 - 65535.
Page 215: Radius-Server Host
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax radius accounting mode no radius accounting mode no - This command is used to set the RADIUS accounting function to the default value - that is, the RADIUS accounting function is disabled.
Page 216: Radius-Sever Key
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - This command is used to remove the configured RADIUS authentication server or the RADIUS accounting server. If the 'auth' token is used, the previously configured RADIUS authentication server is removed from the configuration. Similarly, if the 'acct' token is used, the previously configured RADIUS accounting server is removed from the configuration.
Page 217: Radius-Server Timeout
Korenix Technology Co., Ltd. Layer 3 Stackable Switch response is received from the RADIUS server. The retries value is an integer in the range of 1 to 15. Syntax radius-server retransmit <retries> no radius-server retransmit <retries> - the maximum number of times (Range: 1 - 15).
Page 218: Radius-Server Msgauth
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.8.4.6 radius-server msgauth This command enables the message authenticator attribute for a specified server. Syntax radius-server msgauth <ipaddr> <ipaddr> - is a IP address. Default Setting None Command Mode Global Config 6.8.4.7...
Page 219: Tacacs Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Global Config 6.8.5 TACACS Configuration Commands 6.8.5.1 tacacs This command is used to enable /disable the TACACS function. Syntax tacacs no tacacs no - This command is used to disable the TACACS function.
Page 220: Tacacs Server-Ip
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 6.8.5.3 tacacs server-ip This command is used to configure the TACACS server IP address. Syntax tacacs server-ip <1-3> <ipaddr> no tacacs server-ip <1-3> <ipaddr> - An IP address.
Page 221: Tacacs Key
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Command Mode Global Config 6.8.5.5 tacacs key This command is used to configure the TACACS server shared secret key. Syntax tacacs key <1-3> no tacacs key <1-3> Note that the length of the secret key is up to 32 characters.
Page 222: Tacacs Timeout
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - This command is used to reset retry value to the default value. Default Setting Command Mode Global Config 6.8.5.7 tacacs timeout This command is used to configure the TACACS request timeout of an instance.
Page 223: Port-Security Max-Dynamic
Korenix Technology Co., Ltd. Layer 3 Stackable Switch port-security no port-security Default Setting None Command Mode Global Config, Interface Config 6.8.6.2 port-security max-dynamic This command sets the maximum of dynamically locked MAC addresses allowed on a specific port. Syntax port-security max-dynamic [<0-600>]...
Page 224: Port-Security Mac-Address
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax port-security max-static [<0-20>] no port-security max-static no - This command resets the maximum number of statically locked MAC addresses allowed on a specific port to its default value. Default Setting Command Mode Interface Config 6.8.6.4...
Page 225: Port-Security Mac-Address Move
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.8.6.5 port-security mac-address move This command converts dynamically locked MAC addresses to statically locked addresses. Syntax port-security mac-address move Default Setting None Command Mode Interface Config 6.9 CDP (Cisco Discovery Protocol) Commands 6.9.1 Show Commands...
Page 226: Show Cdp Neighbors
Capability: Describes the device's functional capability in the form of a device type, for example, a switch. Platform: Describes the hardware platform name of the device, for example, Korenix the L2 Network Switch. Port Id: Identifies the port on which the CDP packet is sent.
Page 227: Show Cdp Traffic
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.9.1.3 show cdp traffic This command displays the CDP traffic counters information. Syntax show cdp traffic Default Setting None Command Mode Privileged Exec Display Message Incoming packet number: Received legal CDP packets number from neighbors.
Page 228: Cdp Run
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.9.2.2 cdp run This command is used to enable CDP on a specified interface. Syntax cdp run no cdp run no - This command is used to disable CDP on a specified interface.
Page 229: Cdp Holdtime
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command is used to configure an interval time (seconds) of the sending CDP packet. Syntax cdp timer <5-254> no cdp timer <5-254> - interval time (Range: 5 – 254). no - This command is used to reset the interval time to the default value.
Page 230: Show Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.10.1 Show Commands 6.10.1.1 show sntp This command displays the current time and configuration settings for the SNTP client, and indicates whether the local time has been properly updated. Syntax show sntp...
Page 231: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Client Mode: Configured SNTP Client Mode. Unicast Poll Interval Poll interval value for SNTP clients in seconds as a power of two. Poll Timeout (Seconds) Poll timeout value in seconds for SNTP clients.
Page 232: Sntp Client Mode
Korenix Technology Co., Ltd. Layer 3 Stackable Switch where <poll-interval> can be a value from 6 to 16. Syntax sntp broadcast client poll-interval <6-10> no sntp broadcast client poll-interval <6-10> - The range is 6 to 16. no - This command will reset the poll interval for SNTP broadcast client back to its default value.
Page 233: Sntp Client Port
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Global Config 6.10.2.3 sntp client port This command will set the SNTP client port id and polling interval in seconds. Syntax sntp client port <portid> [<6-10>] no sntp client port <portid> - SNTP client port id.
Page 234: Sntp Unicast Client Poll-Timeout
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting The default value is 6. Command Mode Global Config 6.10.2.5 sntp unicast client poll-timeout This command will set the poll timeout for SNTP unicast clients in seconds. Syntax sntp unicast client poll-timeout <poll-timeout>...
Page 235: Sntp Server
Korenix Technology Co., Ltd. Layer 3 Stackable Switch < poll-retry> - Polling retry in seconds. The range is 0 to 10. no - This command will reset the poll retry for SNTP unicast clients to its default value. Default Setting The default value is 1.
Page 236: System Utilities
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command sets the time zone for the switch’s internal clock. Syntax sntp clock timezone <name> <0-12> <0-59> {before-utc | after-utc} <name> - Name of the time zone, usually an acronym. (Range: 1-15 characters) <0-12>...
Page 237: Clear Traplog
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.11.1.2 clear traplog This command clears the trap log. Syntax clear traplog Default Setting None Command Mode Privileged Exec 6.11.1.3 clear eventlog This command is used to clear the event log, which contains error messages from the system.
Page 238: Clear Config
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax clear logging buffered Default Setting None Command Mode Privileged Exec 6.11.1.5 clear config This command resets the configuration to the factory defaults without powering off the switch. The switch is automatically reset when this command is processed. You are prompted to confirm that the reset should proceed.
Page 239: Clear Counters
Korenix Technology Co., Ltd. Layer 3 Stackable Switch None Command Mode Privileged Exec 6.11.1.7 clear counters This command clears the stats for a specified <unit/slot/port> or for all the ports or for the entire switch based upon the argument. Syntax clear counters [<unit/slot/port>...
Page 240: Clear Dns Cache
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Privileged Exec 6.11.1.9 clear dns cache This command clears all entries from the DNS cache. Syntax clear dns cache Default Setting None Command Mode Privileged Exec 6.11.1.10 clear cdp This command is used to clear the CDP neighbors information and the CDP packet counters.
Page 241: Enable Passwd
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax clear vlan Default Setting None Command Mode Privileged Exec 6.11.1.12 enable passwd This command changes Privileged EXEC password. Syntax enable passwd Default Setting None Command Mode Global Config. 6.11.1.13 clear igmp snooping This command clears the tables managed by the IGMP Snooping function and will attempt to delete these entries from the Multicast Forwarding Database.
Page 242: Clear Port-Channel
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.11.1.14 clear port-channel This command clears all port-channels (LAGs). Syntax clear port-channel Default Setting None Command Mode Privileged Exec 6.11.1.15 clear ip filter This command is used to clear all ip filter entries.
Page 243: Clear Radius Statistics
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax clear dot1x statistics {all | <unit/slot/port>} <unit/slot/port> - is the desired interface number. all - All interfaces. Default Setting None Command Mode Privileged Exec 6.11.1.17 clear radius statistics This command is used to clear all RADIUS statistics.
Page 244: Copy
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec 6.11.2 copy This command uploads and downloads to/from the switch. Local URLs can be specified using tftp or xmodem. The following can be specified as the source file for uploading from the switch: startup config (startup-config), event log (eventlog), message log (msglog) and trap log (traplog).
Page 245 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Privileged Exec Files download from PC to board Syntax copy <url> startup-config <destfilename> copy <url> image <destfilename> copy <url> {sshkey-rsa1 | sshkey-rsa2 | sshkey-dsa} copy <url> {sslpem-root | sslpem-server | sslpem-dhweak | sslpem-dhstrong} copy <url>...
Page 246: Delete
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax copy running-config startup-config [filename] <filename> - name of the configuration file. Default Setting None Command Mode Privileged Exec This command upload or download the pre-login banner file Syntax copy clibanner <url>...
Page 247: Dir
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec 6.11.4 dir This command is used to display a list of files in Flash memory. Syntax dir [boot-rom | config | opcode [<filename>] ] <filename> - name of the configuration or image file.
Page 248: Boot-System
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax whichboot Default Setting None Command Mode Privileged Exec 6.11.6 boot-system This command is used to specify the file or image used to start up the system. Syntax boot-system {boot-rom | config | opcode} <filename>...
Page 249: Traceroute
Korenix Technology Co., Ltd. Layer 3 Stackable Switch there is a physical path between the switch and the workstation. The terminal interface sends, three pings to the target station. Syntax ping <host> <host> - A host name or an IP address.
Page 250: Logging Cli-Command
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 33434. The optional port parameter is the UDP port used as the destination of packets sent as part of the traceroute. This port should be an unused port on the destination system.
Page 251: Reload
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax calendar set <hh:mm:ss> <1-31> <1-12> <2000-2099> <hh:mm:ss> - hh in 24-hour format (Range: 0 - 23), mm (Range: 0 - 59), ss (Range: 0 - <1-31> - Day of month. (Range: 1 - 31).
Page 252: Disconnect
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command is used to activate global configuration mode Syntax configure Default Setting None Command Mode Privileged Exec 6.11.13 disconnect This command is used to close a telnet session. Syntax disconnect {<0-10> | all} <0-11>...
Page 253: Quit
Korenix Technology Co., Ltd. Layer 3 Stackable Switch < prompt_string > - Prompt string. Default Setting Korenix Command Mode Privileged Exec 6.11.15 quit This command is used to exit a CLI session. Syntax quit Default Setting None Command Mode Privileged Exec 6.12 Differentiated Service Command...
Page 254: General Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Packets are filtered and processed based on defined criteria. The filtering criteria are defined by a class. The processing is defined by a policy's attributes. Policy attributes may be defined on a per class instance basis, and it is these attributes that are applied when a match occurs.
Page 255: No Diffserv
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command sets the DiffServ operational mode to active. While disabled, the DiffServ configuration is retained and can be changed, but it is not activated. When enabled, Diffserv services are activated. Syntax...
Page 256: Class-Map
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.2.1 class-map This command defines a new DiffServ class of type match-all, match-any or match-access-group. Syntax class-map [ match-all ] <class-map-name> <class-map-name> is a case sensitive alphanumeric string from 1 to 31 characters uniquely identifying the class.
Page 257: Class-Map Rename
Korenix Technology Co., Ltd. Layer 3 Stackable Switch issued at any time; if the class is currently referenced by one or more policies or by any other class, this deletion attempt shall fail. Command Mode Global Config 6.12.2.3 class-map rename This command changes the name of a DiffServ class.
Page 258: Match Class-Map
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.2.5 match class-map This command adds to the specified class definition the set of match conditions defined for another class. Syntax match class-map <refclassname> <refclassname> is the name of an existing DiffServ class whose match conditions are being referenced by the specified class definition.
Page 259: Match Dstip
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Note: There is no [not] option for this match command. Default None Command Mode Class-Map Config 6.12.2.7 match dstip This command adds to the specified class definition a match condition based on the destination IP address of a packet.
Page 260: Match Ip Dscp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch The port number is an integer from 0 to 65535. To specify the match condition using a numeric range notation, two layer 4 port numbers are required and together they specify a contiguous port range. Each port number is an integer from 0 to 65535, but with the added requirement that the second number be equal to or greater than the first.
Page 261: Match Ip Tos
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Type octet in the IP header (the low-order five bits are not checked). The precedence value is an integer from 0 to 7. Syntax match ip precedence <0-7> Note: The ip dscp, ip precedence, and ip tos match conditions are alternative ways to specify a match criterion for the same Service Type field in the IP header, but with a slightly different user notation.
Page 262: Match Protocol
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default None Command Mode Class-Map Config 6.12.2.12 match protocol This command adds to the specified class definition a match condition based on the value of the IP Protocol field in a packet using a single keyword notation or a numeric value notation.
Page 263: Match Srcl4Port
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default None Command Mode Class-Map Config 6.12.2.14 match srcl4port This command adds to the specified class definition a match condition based on the source layer 4 port of a packet using a single keyword or numeric notation or a numeric range notation.
Page 264: Assign-Queue
Korenix Technology Co., Ltd. Layer 3 Stackable Switch The policy commands are used to associate a traffic class, which was defined by the class command set, with one or more QoS policy attributes. This association is then assigned to an interface in a particular direction to form a service.
Page 265: Redirect
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax drop Command Mode Policy-Class-Map Config 6.12.3.3 redirect This command specifies that all incoming packets for the associated traffic stream are redirected to a specific egress interface (physical port or port-channel). Syntax redirect <unit/slot/port>...
Page 266: Mark Cos
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax conform-color <class-map-name> <class-map-name> - Name of an existing Diffserv class map, where different ones must be used for the conform colors. Command Mode Policy-Class-Map Config 6.12.3.5 mark cos This command marks all packets for the associated traffic stream with the specified class of service value in the priority field of the 802.1p header.
Page 267: No Class
Korenix Technology Co., Ltd. Layer 3 Stackable Switch class <classname> <classname> is the name of an existing DiffServ class. Note that this command causes the specified policy to create a reference to the class definition. Command Mode Policy-Class-Map Config 6.12.3.7 no class This command deletes the instance of a particular class and its defined treatment from the specified policy.
Page 268: Police-Simple
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Precedence value. The IP Precedence value is an integer from 0 to 7. Syntax mark ip-precedence <0-7> Command Mode Policy-Class-Map Config Policy Type In Incompatibilities Mark IP DSCP, Police (all forms) 6.12.3.10 police-simple This command is used to establish the traffic policing style for the specified class.
Page 269: Policy-Map
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.3.11 policy-map This command establishes a new DiffServ policy. The <policyname> parameter is a case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying the policy. The type of policy is specific to the inbound traffic direction as indicated by the in parameter.
Page 270: Service-Policy
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Traffic Conditioning Assign a DiffServ traffic conditioning policy (as specified by the policy commands) to an interface in the incoming direction. Service Provisioning Assign a DiffServ service provisioning policy (as specified by the policy commands) to an interface in the outgoing direction The service commands attach a defined policy to a directional interface.
Page 271: No Service-Policy
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.4.2 no service-policy This command detaches a policy from an interface in a particular direction. Syntax no service-policy in <policy-map-name> The command can be used in the Interface Config mode to detach a policy from a specific interface.
Page 272 Korenix Technology Co., Ltd. Layer 3 Stackable Switch <classname> is the name of an existing DiffServ class. Default Setting None Command Mode Privileged EXEC and User EXEC Display Message Class Name The name of this class. Class Type The class type (all, any, or acl) indicating how the match criteria are evaluated for this class.
Page 273: Show Diffserv
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.5.2 show diffserv This command displays the DiffServ General Status Group information, which includes the current administrative mode setting as well as the current and maximum number of rows in each of the main DiffServ private MIB tables.
Page 274 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Privileged EXEC Display Message Policy Name The name of this policy. Policy Type The policy type, namely whether it is an inbound or outbound policy definition. The following information is repeated for each class associated with this policy (only those policy attributes actually configured are displayed): Class Name The name of this class.
Page 275: Show Diffserv Service
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Bandwidth This field displays the minimum amount of bandwidth reserved in either percent or kilobits-per-second. Policy Name The name of this policy. (Note that the order in which the policies are displayed is not necessarily the same order in which they were created.)
Page 276: Show Diffserv Service Brief
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.5.5 show diffserv service brief This command displays all interfaces in the system to which a DiffServ policy has been attached. The direction parameter is optional; if specified, only services in the indicated direction are shown.
Page 277 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Interface The slot number and port number of the interface (unit/slot/port). Direction The traffic direction of this interface service, either in or out. Operational Status The current operational status of this DiffServ service interface.
Page 278: Show Service-Policy
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.12.5.7 show service-policy This command displays a summary of policy-oriented statistics information for all interfaces in the specified direction. The direction parameter indicates the interface direction of interest. This command enables or disables the route reflector client. A route reflector client relies on a route reflector to re-advertise its routes to the entire AS.
Page 279: Show Mac Access-Lists
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged EXEC Display Message MAC ACL Name The name of the MAC ACL rule. Rule Number The ordered rule number identifier defined within the ACL. Action Displays the action associated with each rule. The possible values are Permit or Deny.
Page 280: Show Ip Access-Lists
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Current number of all ACLs The number of user-configured rules defined for this ACL. Maximum number of all ACLs The maximum number of ACL rules. MAC ACL Name The name of the MAC ACL rule.
Page 281: Show Access-Lists Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Match (IP DSCP, IP Precedence, or IP TOS). 6.13.1.4 show access-lists interface This command displays Access List information for a particular interface and the 'in' direction. Syntax show access-lists interface <unit/slot/port> in <unit/slot/port>...
Page 282: Mac Access-List Extended
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no mac access-list extended <name> <name> - It uniquely identifies the MAC access list. Default Setting None Command Mode Global Config 6.13.2.2 mac access-list extended This command changes the name of a MAC Access Control List (ACL). The <name>...
Page 283: Mac Access-Group In
Korenix Technology Co., Ltd. Layer 3 Stackable Switch A rule may either deny or permit traffic according to the specified classification fields. At a minimum, the source and destination MAC value and mask pairs must be specified, each of which may be substituted using the keyword any to indicate a match on any value in that field.
Page 284: Access-List
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax mac access-group <name> in [<1-4294967295>] no mac access-group <name> in <no> - This command removes a MAC ACL identified by <name> from the interface in a given direction. Default Setting None...
Page 285: No Access-List
Korenix Technology Co., Ltd. Layer 3 Stackable Switch dscp. Default Setting None Command Mode Global Config 6.13.2.6 no access-list This command deletes an ACL that is identified by the parameter <accesslistnumber> from the system. Syntax no access-list {<1-99> | <100-199>} Note: The ACL number is an integer from 1 to 199.
Page 286: Cos (Class Of Service) Command
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config, Interface Config 6.14 CoS (Class of Service) Command 6.14.1 Show Commands 6.14.1.1 show queue cos-map This command displays the current Dot1p (802.1p) priority mapping to internal traffic classes for a specific interface.
Page 287: Show Queue Trust
Korenix Technology Co., Ltd. Layer 3 Stackable Switch independent per-port class of service mappings. If specified, the IP Precedence mapping table of the interface is displayed. If omitted, the most recent global configuration settings are displayed. Syntax show queue ip-precedence-mapping <unit/slot/port>...
Page 288: Show Queue Cos-Queue
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged EXEC, User EXEC Display Message Class of Service Trust Mode The trust mode of this interface. Non-IP Traffic ClassThe traffic class used for non-IP traffic. This is only displayed when the COS trust mode is set to either 'trust ip-dscp' or 'trust ip-precedence'.
Page 289: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch platform dependent. Minimum Bandwidth The minimum transmission bandwidth guarantee for the queue, expressed as a percentage. A value of 0 means bandwidth is not guaranteed and the queue operates using best-effort. This is a configured value.
Page 290: Queue Ip-Precedence-Mapping
Korenix Technology Co., Ltd. Layer 3 Stackable Switch < 0-7 > - The range of queue priority is 0 to 7. < 0-6 > - The range of mapped traffic class is 0 to 6. no - Reset to the default mapping of the queue priority and the mapped traffic class.
Page 291: Queue Trust
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no queue ip-precedence-mapping all < 0-7 > - The range of IP precedence is 0 to 7. < 0-6 > - The range of mapped traffic class is 0 to 6. no - Reset to the default mapping of the IP precedence and the mapped traffic class.
Page 292: Queue Cos-Queue Min-Bandwidth
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax queue trust all {dot1p | ip-precedence | ip-dscp} no queue trust all no - This command sets the class of service trust mode to untrusted for all interfaces. Default Setting None Command Mode Global Config.
Page 293: Queue Cos-Queue Strict
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command specifies the minimum transmission bandwidth guarantee for each interface queue in the device. Syntax queue cos-queue min-bandwidth all <bw-0> <bw-1> … <bw-6> no queue cos-queue min-bandwidth all <bw-0> <bw-1> … <bw-6>- Each Valid range is (0 to 100) in increments of 5 and the total sum is less than or equal to 100.
Page 294: Queue Cos-Queue Traffic-Shape
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Interface Config. This command activates the strict priority scheduler mode for each specified queue on a device. Syntax queue cos-queue strict all <queue-id-0> [<queue-id-1> … <queue-id-6>] no queue cos-queue strict all <queue-id-0> [<queue-id-1> … <queue-id-6>] no - This command restores the default weighted scheduler mode for each specified queue on a device.
Page 295 Korenix Technology Co., Ltd. Layer 3 Stackable Switch queue cos-queue traffic-shape <bw> no queue cos-queue traffic-shape <bw> - Valid range is (0 to 100) in increments 5. no - This command restores the default shaping rate value. Default Setting None Command Mode Interface Config.
Page 296: Lldp (Link Layer Discovery Protocol) Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 6.15 LLDP (Link Layer Discovery Protocol) Commands 6.15.1 Show Commands 6.15.1.1 show lldp This command uses to display a summary of the current LLDP configuration. Syntax show lldp Default Setting None Command Mode...
Page 297: Show Lldp Statistics
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Privileged Exec Display Message Interface: Shows the interface in a unit/slot/port format. Link: Shows whether the link is up or down. Transmit: Shows whether the interface transmits LLDPDUs. Receive: Shows whether the interface receives LLDPDUs.
Page 298: Show Lldp Remote-Device
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Discards: Total number of LLDP frames discarded on the port for any reason. Errors: The number of invalid LLDP frames received on the port. Ageouts: Total number of times a complete remote data entry was deleted for the port because the Time to Live interval expired.
Page 299: Show Lldp Local-Device
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <unit/slot/port> - Displays a specific interface. Default Setting None Command Mode Privileged Exec Display Message Local Interface: Identifies the interface that received the LLDPDU from the remote device. Chassis ID Subtype: Shows the type of identification used in the Chassis ID field.
Page 300: Show Lldp Local-Device Detail
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Privileged Exec Display Message Interface: Identifies the interface in a unit/slot/port format. Port ID: Shows the port ID associated with this interface. Port Description: Shows the port description associated with the interface.
Page 301: Routing Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7 Routing Commands 7.1 Address Resolution Protocol (ARP) Commands 7.1.1 Show Commands 7.1.1.1 show ip arp This command displays the Address Resolution Protocol (ARP) cache. Syntax show ip arp Default Setting None...
Page 302: Show Ip Arp Brief
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.1.1.2 show ip arp brief This command displays the brief Address Resolution Protocol (ARP) table information. Syntax show ip arp brief Default Setting None Command Mode Privileged Exec Display Message Age Time: Is the time it takes for an ARP entry to age out. This value was configured into the unit.
Page 303: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.1.2 Configuration Commands 7.1.2.1 This command creates an ARP entry. The value for <ipaddress> is the IP address of a device on a subnet attached to an existing routing interface. The value for <macaddress> is a unicast MAC address for that device.
Page 304: Arp Cachesize
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Interface Config 7.1.2.3 arp cachesize This command configures the maximum number of entries in the ARP cache. Syntax arp cachesize <256-1920> no arp cachesize <256-1920> - The range of cache size is 256 to 1920.
Page 305: Arp Resptime
Korenix Technology Co., Ltd. Layer 3 Stackable Switch arp purge <ipaddr> <ipaddr> - The IP address to be removed from the ARP table. Default Setting None Command Mode Privileged Exec 7.1.2.6 arp resptime This command configures the ARP request response timeout.
Page 306: Clear Arp-Cache
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command configures the ARP entry ageout time. Syntax arp timeout <15-21600> no arp timeout <15-21600> - Represents the IP ARP entry ageout time in seconds. The range is 15 to 21600 seconds.
Page 307: Show Ip Interface Port
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec, User Exec Display Message Default Time to Live: The computed TTL (Time to Live) of forwarding a packet from the local router to the final destination.
Page 308: Show Ip Interface Brief
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Encapsulation Type: Is the encapsulation type for the specified interface. IP Mtu: Is the Maximum Transmission Unit size of the IP packet. 7.2.1.3 show ip interface brief This command displays summary information about IP configuration settings for all ports in the router.
Page 309: Show Ip Route Bestroutes
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Total Number of Routes: The total number of routes. for each next hop Network Address: Is an IP address identifying the network on the specified interface. Subnet Mask: Is a mask of the network and host portion of the IP address for the router interface.
Page 310: Show Ip Route Precedence
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show ip route entry <networkaddress> <networkaddress> - Is a valid network address identifying the network on the specified interface. Default Setting None Command Mode Privileged Exec Display Message Network Address: Is a valid network address identifying the network on the specified interface.
Page 311: Show Ip Traffic
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Privileged Exec, User Exec Display Message Local: This field displays the local route preference value. Static: This field displays the static route preference value. OSPF Intra: This field displays the OSPF intra route preference value.
Page 312: Ip Routing
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Enabled Command Mode Interface Config 7.2.2.2 ip routing This command enables the IP Router Admin Mode for the master switch. Syntax ip routing no ip routing no - Disable the IP Router Admin Mode for the master switch.
Page 313: Ip Route Default-Next-Hop
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command configures a static route. Syntax ip route <networkaddr> <subnetmask> [ <nexthopip> [<1-255 >] ] no ip route <networkaddr> <subnetmask> [ { <nexthopip> | <1-255 > } ] <ipaddr> - A valid IP address .
Page 314: Ip Forwarding
Korenix Technology Co., Ltd. Layer 3 Stackable Switch allow you to optionally set the precedence of an individual static route. The default precedence is used when no precedence is specified in these commands. Changing the default precedence does not update the precedence of existing static routes, even if they were assigned the original default precedence.
Page 315: Ip Mtu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ip directed-broadcast no ip directed-broadcast no - Drop network directed broadcast packets. Default Setting Enabled Command Mode Interface Config 7.2.2.9 ip mtu This command sets the IP Maximum Transmission Unit (MTU) on a routing interface. The IP MTU is the size of the largest IP packet that can be transmitted on the interface without fragmentation.
Page 316: Open Shortest Path First (Ospf) Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting The default value is ethernet. Command Mode Interface Config Restrictions Routed frames are always Ethernet encapsulated when a frame is routed to a VLAN. 7.3 Open Shortest Path First (OSPF) Commands 7.3.1 Show Commands...
Page 317: Show Ip Ospf Area
Korenix Technology Co., Ltd. Layer 3 Stackable Switch External LSA Checksum A number which represents the sum of the LS checksums of external link-state advertisements contained in the link-state database. New LSAs Originated The number of new link-state advertisements that have been originated.
Page 318: Show Ip Ospf Database
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.3.1.3 show ip ospf database This command displays the link state database. This command takes no options. The information will only be displayed if OSPF is enabled. Syntax show ip ospf database...
Page 319: Show Ip Ospf Interface Brief
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Subnet Mask Is a mask of the network and host portion of the IP address for the OSPF interface. This value was configured into the unit. This is a configured value. OSPF Admin Mode States whether OSPF is enabled or disabled on a router interface. This is a configured value.
Page 320: Show Ip Ospf Interface Stats
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Retrax Interval A number representing the OSPF Retransmit Interval for the specified interface. This is a configured value. Retrax Delay A number representing the OSPF Transit Delay for the specified interface. This is a configured value.
Page 321 Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays the OSPF neighbor table list. When a particular neighbor ID is specified, detailed information about a neighbor is given. The information will only be displayed if OSPF is enabled and the interface has a neighbor.
Page 322: Show Ip Ospf Neighbor Brief
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Retransmission Queue Length Is an integer representing the current length of the retransmission queue of the specified neighbor router Id of the specified interface. 7.3.1.8 show ip ospf neighbor brief This command displays the OSPF neighbor table list. When a particular neighbor ID is specified, detailed information about a neighbor is given.
Page 323: Show Ip Ospf Stub Table
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <areaid> identifies the OSPF area whose ranges are being displayed. Syntax show ip ospf range <areaid> <areaid> - The area id of the requested OSPF area Default Setting None Command Mode Privileged Exec, User Exec Display Messages Area ID The area id of the requested OSPF area.
Page 324: Show Ip Ospf Virtual-Link
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Metric Val The metric value is applied based on the TOS. It defaults to the least metric of the type of service among the interfaces to other areas. The OSPF cost for a route is a function of the metric value.
Page 325: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show ip ospf virtual-link brief Default Setting None Command Mode Privileged Exec, User Exec Display Messages Area Id Is the area id of the requested OSPF area. Neighbor Is the neighbor interface of the OSPF virtual interface.
Page 326: No Area
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.3.2.2 no area This command removes an OSPF area. Syntax no area <areaid> Default Setting None Command Mode Router OSPF Config 7.3.2.3 ip ospf This command enables OSPF on a router interface.
Page 327: Area Default-Cost
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax 1583compatibility no 1583compatibility <no> - This command disables OSPF 1583 compatibility. Default Setting Enabled Command Mode Router OSPF Config 7.3.2.5 area default-cost This command configures the monetary default cost for the stub area.
Page 328: Area Nssa Default-Info-Originate
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <areaid> - Area ID. <no> - This command disables nssa from the specified area id. Default Setting None Command Mode Router OSPF Config 7.3.2.7 area nssa default-info-originate This command configures the metric value and type for the default route advertised into the NSSA.
Page 329: Area Nssa No-Summary
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Router OSPF Config 7.3.2.9 area nssa no-summary This command configures the NSSA so that summary LSAs are not advertised into the NSSA Syntax area <areaid> nssa no- summary <areaid>...
Page 330: Area Nssa Translator-Stab-Intv
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Router OSPF Config 7.3.2.11 area nssa translator-stab-intv This command configures the translator stability interval of the NSSA. The <stabilityinterval> is the period of time that an elected translator continues to perform its duties after it determines that its translator status has been deposed by another router.
Page 331: Area Stub
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Router OSPF Config 7.3.2.13 area stub This command creates a stub area for the specified area ID. A stub area is characterized by the fact that AS External LSAs are not propagated into the area. Removing AS External LSAs and Summary LSAs can significantly reduce the link state database of routers within the stub area.
Page 332: Area Virtual-Link Authentication
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <areaid> - Area ID. <no> - This command configures the default Summary LSA mode for the specified stub area. Default Setting Disabled Command Mode Router OSPF Config 7.3.2.15 area virtual-link authentication This command configures the authentication type and key for the OSPF virtual interface identified by <areaid>...
Page 333: Area Virtual-Link Dead-Interval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.3.2.16 area virtual-link dead-interval This command configures the dead interval for the OSPF virtual interface on the virtual interface identified by <areaid> and <neighborid>. Syntax area <areaid> virtual-link <neighborid> dead-interval <1-65535> no area <areaid> virtual-link <neighborid> dead-interval <areaid>...
Page 334: Area Virtual-Link Retransmit-Interval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch The default value of hello interval is 10 seconds. Command Mode Router OSPF Config 7.3.2.18 area virtual-link retransmit-interval This command configures the retransmit interval for the OSPF virtual interface on the interface identified by <areaid>...
Page 335: Default-Information Originate
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <0-3600> - The range of the transmit delay is 0 to 3600. <no> - This command configures the default transmit delay for the OSPF virtual interface on the virtual interface identified by <areaid> and <neighborid>.
Page 336: Distance Ospf
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax default-metric <1-16777215> no default-metric <1-16777215> - The range of default metric is 1 to 16777215. <no> - This command configures the default advertisement of default routes. Default Setting None Command Mode Router OSPF Config 7.3.2.22...
Page 337: Distribute-List Out
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.3.2.23 distribute-list out This command is used to specify the access list to filter routes received from the source protocol. Syntax distribute-list <1-199> out {rip | static | connected} no distribute-list <1-199> out {rip | static | connected} <1-199>...
Page 338: External-Lsdb-Limit
Korenix Technology Co., Ltd. Layer 3 Stackable Switch The default value of exit overflow interval for OSPF is 0. Command Mode Router OSPF Config 7.3.2.25 external-lsdb-limit This command configures the external LSDB limit for OSPF. If the value is -1, then there is no limit.
Page 339: Ip Ospf Authentication
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ip ospf areaid <areaid> < areaid > - It is an IP address, formatted as a 4-digit dotted-decimal number that uniquely identifies the area to which the interface connects. Default Setting None...
Page 340: Ip Ospf Cost
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.3.2.28 ip ospf cost This command configures the cost on an OSPF interface. Syntax ip ospf cost <1-65535> no ip ospf cost < 1-65535 > - The range of the cost is 1 to 65535.
Page 341: Ip Ospf Hello -Interval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting The default dead interval is 40 seconds. Command Mode Interface Config 7.3.2.30 ip ospf hello -interval This command sets the OSPF hello interval for the specified interface. Syntax ip ospf hello-interval <1-65535>...
Page 342: Ip Ospf Retransmit-Interval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch router is not eligible to become the designated router on this network. <no> - This command sets the default OSPF priority for the specified interface. Default Setting The default priority value is 1. It is the highest router priority.
Page 343: Ip Ospf Mtu-Ignore
Korenix Technology Co., Ltd. Layer 3 Stackable Switch link state update packet over this interface. Syntax ip ospf transmit-delay <1-3600> no ip ospf transmit-delay < 1-3600 > - The range of transmit delay is 1 to 3600. <no> - This command sets the default OSPF Transit Delay for the specified interface.
Page 344: Router-Id
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Interface Config 7.3.2.35 router-id This command sets a 4-digit dotted-decimal number uniquely identifying the router ospf id. Syntax router-id <ipaddress> < ipaddress > - IP Address. Default Setting None. Command Mode Router OSPF Config 7.3.2.36 redistribute...
Page 345: Maximum-Paths
Korenix Technology Co., Ltd. Layer 3 Stackable Switch The default value of metric is unspecified. The default value of metric type is 2. The default value of tag is 0. Command Mode Router OSPF Config 7.3.2.37 maximum-paths This command sets the number of paths that OSPF can report for a given destination where <maxpaths>...
Page 346: Bootpdhcprelay Cidoptmode
Korenix Technology Co., Ltd. Layer 3 Stackable Switch None Command Mode Privileged Exec, User Exec Display Message Maximum Hop Count: Is the maximum allowable relay agent hops. Minimum Wait Time (Seconds) Is the minimum wait time. Admin Mode Represents whether relaying of requests is enabled or disabled.
Page 347: Bootpdhcprelay Maxhopcount
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 7.4.4 bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. Syntax bootpdhcprelay maxhopcount <1-16> no bootpdhcprelay maxhopcount <count> - The range of maximum hop count is 1 to 16.
Page 348: Bootpdhcprelay Serverip
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.4.6 bootpdhcprelay serverip This command configures the server IP Address for BootP/DHCP Relay on the system. Syntax bootpdhcprelay serverip <ipaddr> no bootpdhcprelay serverip <ipaddr> - The IP address of the BootP/DHCP server.
Page 349: Domain Name Server Relay Commands
<text> - A text string which length is 1 to 15. <hex> - A hex string which format is XX:XX:XX:XX:XX:XX (X is 0-9, A-F). Default Setting The default value for client-identifier is a text string "Korenix". Command Mode Global Config 7.5 Domain Name Server Relay Commands...
Page 350: Show Dns Cache
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message Domain Lookup Status: Enable or disable the IP Domain Naming System (DNS)-based host name-to-address translation function. Default Domain Name: The default domain name that will be used for querying the IP address of a host.
Page 351: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.5.2 Configuration Commands 7.5.2.1 ip hosts This command creates a static entry in the DNS table that maps a host name to an IP address. Syntax ip host <name> <ipaddr> no ip host <name>...
Page 352: Ip Domain-Name
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.5.2.3 ip domain-name This command defines the default domain name to be appended to incomplete host names (i.e., host names passed from a client are not formatted with dotted notation). Syntax ip domain-name <name>...
Page 353: Ip Name-Server
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec 7.5.2.5 ip name-server This command specifies the address of one or more domain name servers to use for name-to-address resolution. There are maximum 6 entries in the Domain Name Server Table.
Page 354: Clear Domain-List
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec 7.5.2.7 clear domain-list This command clears all entries in the domain name list table. Syntax clear domain-list Default Setting None Command Mode Privileged Exec 7.5.2.8 clear dns This command sets the DNS configuration to default value.
Page 355: Clear Dns Cache
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Privileged Exec 7.5.2.9 clear dns cache This command clears all entries in the DNS cache table. Syntax clear dns cache Default Setting None Command Mode Privileged Exec 7.5.2.10 clear dns counter This command clears the statistics of all entries in the DNS cache table.
Page 356: Show Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.6.1 Show Commands 7.6.1.1 show ip rip This command displays information relevant to the RIP router. Syntax show ip rip Default Setting None Command Mode Privileged Exec Display Message RIP Admin Mode: Select enable or disable from the pulldown menu. If you select enable RIP will be enabled for the switch.
Page 357: Show Ip Rip Interface Brief
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show ip rip interface <unit/slot/port> < unit/slot/port > - Interface number Default Setting None Command Mode Privileged Exec Display Message Interface: Valid unit, slot and port number separated by forward slashes. This is a configured value.
Page 358: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch show ip rip interface brief Default Setting None Command Mode Privileged Exec Display Message Interfacet: Valid unit, slot and port number separated by forward slashes. IP Address: The IP source address used by the specified RIP interface.
Page 359: Auto-Summary
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command enables RIP on a router interface. Syntax Ip rip no ip rip no - This command disables RIP on a router interface. Default Setting Disabled Command Mode Interface Config 7.6.2.3 auto-summary This command enables the RIP auto-summarization mode.
Page 360: Default-Metric
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax default-information originate no default-information originate no - This command is used to cancel the advertisement of default routes. Default Setting Not configured Command Mode Router RIP Config 7.6.2.5 default-metric This command is used to set a default for the metric of distributed routes.
Page 361: Hostrouteaccept
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax distance rip <1-255> no distance rip <1 - 255> - the value for distance. no - This command sets the default route preference value of RIP in the router. Default Setting...
Page 362: Distribute-List
Korenix Technology Co., Ltd. Layer 3 Stackable Switch learned. Poison mode will be that routes learned over this interface should be re-advertised on the interface with a metric of infinity (16). Syntax split-horizon {none | simple | poison} no split-horizon none - This command sets without using RIP split horizon mode.
Page 363: Redistribute
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Router RIP Config 7.6.2.10 redistribute This command configures RIP protocol to redistribute routes from the specified source protocol/routers. There are five possible match options. When you submit the command redistribute ospf match <matchtype> the match-type or types specified are added to any match types presently being redistributed.
Page 364: Ip Rip Receive Version
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax ip rip authentication {none | {simple <key>} | {encrypt <key> <keyid>}} no ip rip authentication none - This command uses no authentication. simple - This command uses simple authentication for RIP authentication .
Page 365: Ip Rip Send Version
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Interface Config 7.6.2.13 ip rip send version This command configures the interface to allow RIP control packets of the specified version to be sent. The value for <mode> is one of: rip1 to broadcast RIP version 1 formatted packets, rip1c (RIP...
Page 366: Ip Irdp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <all> - Show router discovery information for all interfaces. Default Setting None Command Mode Privileged Exec, User Exec Display Message Ad Mode Displays the advertise mode which indicates whether router discovery is enabled or disabled on this interface.
Page 367: Ip Irdp Holdtime
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ip irdp broadcast no ip irdp broadcast broadcast - The address used is 255.255.255.255. no - The address used is 224.0.0.1. Default Setting The default address is 224.0.0.1 Command Mode Interface Config 7.7.4...
Page 368: Ip Irdp Minadvertinterval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch < minadvertinterval-1800 > - The range is 4 to 1800 seconds. no - This command configures the default maximum time, in seconds. Default Setting The default value is 600. Command Mode Global Config 7.7.6...
Page 369: Vlan Routing Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch < -2147483648-2147483647> - The range is -2147483648 to 2147483647. no - This command sets the preference to 0. Default Setting The default value is 0. Command Mode Global Config 7.8 VLAN Routing Commands 7.8.1 show ip vlan...
Page 370: Virtual Router Redundancy Protocol (Vrrp) Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch vlan routing <vlanid> no vlan routing <vlanid> <vlanid> - The range is 1 to 3965. no - Delete routing on a VLAN. Default Setting None Command Mode VLAN Database 7.9 Virtual Router Redundancy Protocol (VRRP) Commands 7.9.1 Show Commands...
Page 371: Show Ip Vrrp Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays information about each virtual router configured on the switch. Syntax show ip vrrp brief Default Setting None Command Mode Privileged Exec, User Exec Display Message Interface Valid unit, slot and port number separated by forward slashes.
Page 372: Show Ip Vrrp Interface Stats
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Administrative Mode Represents the status (Enable or Disable) of the specific router. State Represents the state (Master/backup) of the specific virtual router 7.9.1.4 show ip vrrp interface stats This command displays the statistical information about each virtual router configured on the switch.
Page 373: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.9.2 Configuration Commands 7.9.2.1 ip vrrp This command enables the administrative mode of VRRP in the router. Syntax ip vrrp no ip vrrp Default Setting Disabled Command Mode Global Config This command sets the virtual router ID on an interface for Virtual Router configuration in the router.
Page 374: Ip Vrrp Ip
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.9.2.2 ip vrrp ip This commands also designates the configured virtual router IP address as a secondary IP address on an interface. Syntax ip vrrp <1-255> ip <addr> [secondary] no ip vrrp <1-255> ip <addr> [secondary] <1-255>...
Page 375: Ip Vrrp Authentication
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.9.2.4 ip vrrp authentication This command sets the authorization details value for the virtual router configured on a specified interface. Syntax ip vrrp <1-255> authentication <key> no ip vrrp <1-255> authentication <1-255> - The range of virtual router ID is 1 to 255.
Page 376: Ip Vrrp Priority
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 7.9.2.6 ip vrrp priority This command sets the priority value for the virtual router configured on a specified interface. Syntax ip vrrp <1-255> priority <1-255> no ip vrrp <1-255> priority <1-255> - The range of virtual router ID is 1 to 255.
Page 377: Ip Multicast Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8 IP Multicast Commands 8.1 Distance Vector Multicast Routing Protocol (DVMRP) Commands This section provides a detailed explanation of the DVMRP commands. The commands are divided into the following different groups: Show commands are used to display device settings, statistics and other information.
Page 378: Show Ip Dvmrp Neighbor
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show ip dvmrp interface <unit/slot/port> Default Setting None Command Mode Privileged Exec User EXEC Display Message Interface Mode This field indicates whether DVMRP is enabled or disabled on the specified interface. This is a configured value.
Page 379: Show Ip Dvmrp Nexthop
Korenix Technology Co., Ltd. Layer 3 Stackable Switch applicable if the State is DOWN. Generation ID This is the Generation ID value for the neighbor. Major Version This shows the major version of DVMRP protocol of neighbor. Minor Version This shows the minor version of DVMRP protocol of neighbor.
Page 380: Show Ip Dvmrp Route
Korenix Technology Co., Ltd. Layer 3 Stackable Switch User EXEC Display Message Group IP This field identifies the multicast Address that is pruned. Source IP This field displays the IP Address of the source that has pruned. Source Mask This field displays the network Mask for the prune source. It should be all 1s or both the prune source and prune mask must match.
Page 381: Ip Dvmrp Metric
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no - This command sets administrative mode of DVMRP in the router to inactive. IGMP must be enabled before DVMRP can be enabled. Default Setting Disabled Command Mode Global Config 8.1.2.2 ip dvmrp metric This command configures the metric for an interface.
Page 382: Show Ip Igmp Groups
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays the system-wide IGMP information. Syntax show ip igmp Default Setting None Command Mode Privileged Exec User EXEC Display Message IGMP Admin Mode This field displays the administrative status of IGMP. This is a configured value.
Page 383: Show Ip Igmp Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Non-Querier mode. Groups This displays the list of multicast groups that are registered on this interface. If detail is specified, the following fields are displayed: Multicast IP Address This displays the IP Address of the registered multicast group on this interface.
Page 384: Show Ip Igmp Interface Membership
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Startup Query Interval (secs) This value indicates the interval between General Queries sent by a Querier on startup. This is a configured value. Startup Query Count This value is the number of Queries sent out on startup, separated by the Startup Query Interval.
Page 385: Show Ip Igmp Interface Stats
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.2.1.5 show ip igmp interface stats This command displays the IGMP statistical information for the given interface. The statistics are only displayed when the interface is enabled for IGMP. Syntax show ip igmp interface stats <unit/slot/port>...
Page 386: Ip Igmp Version
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no ip igmp no - This command sets the administrative mode of IGMP in the router to inactive. Default Setting Disabled Command Mode Global Config 8.2.2.2 ip igmp version This command configures the version of IGMP for an interface.
Page 387: Ip Igmp Last-Member-Query-Interval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch <1-20> - The range for <1-20> is 1 to 20. no - This command resets the number of Group-Specific Queries to the default value. Default Setting Disabled Command Mode Interface Config 8.2.2.4...
Page 388: Ip Igmp Query-Max-Response-Time
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting 125 seconds Command Mode Interface Config 8.2.2.6 ip igmp query-max-response-time This command configures the maximum response time interval for the specified interface, which is the maximum query response time advertised in IGMPv2 queries on this interface.The time interval is specified in tenths of a second.
Page 389: Ip Igmp Startup-Query-Count
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Command Mode Interface Config 8.2.2.8 ip igmp startup-query-count This command sets the number of Queries sent out on startup, separated by the Startup Query Interval on the interface. Syntax ip igmp startup-query-count <1-20>...
Page 390: Multicast Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting Command Mode Interface Config 8.3 Multicast Commands 8.3.1 Show Commands 8.3.1.1 show ip mcast This command displays the system-wide multicast information Syntax show ip mcast Default Setting None Command Mode...
Page 391: Show Ip Mcast Boundary
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.3.1.2 show ip mcast boundary This command displays all the configured administrative scoped multicast boundaries. Syntax show ip mcast boundary {<unit/slot/port> | all} < unit/slot/port > - Interface number. all - This command represents all interfaces.
Page 392: Show Ip Mcast Mroute
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Display Message Interface: Valid unit, slot and port number separated by forward slashes. TTL: This field displays the time-to-live value for this interface. 8.3.1.4 show ip mcast mroute This command displays a summary or all the details of the multicast table.
Page 393 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax show ip mcast mroute group <groupipaddr> {detail |summary} < groupipaddr > - the IP Address of the destination of the multicast packet. Default Setting None Command Mode Privileged Exec Display Message If the detail parameter is specified the follow fields are displayed: Source IP: This field displays the IP address of the multicast data source.
Page 394 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message If the < groupipaddr > parameter is specified the follow fields are displayed: Source IP: This field displays the IP address of the multicast data source.
Page 395: Show Mrinfo
Korenix Technology Co., Ltd. Layer 3 Stackable Switch mask. Metric: This field displays the metric value corresponding to the source address. Interface: Valid unit, slot and port number separated by forward slashes. 8.3.1.5 show mrinfo This command is used to display the neighbor information of a multicast-capable router from the results buffer pool of the router subsequent to the execution/completion of a "mrinfo...
Page 396: Show Mtrace
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message 8.3.1.7 show mtrace This command is used to display results of multicast trace path from the results buffer pool of the router, subsequent to the execution/completion of a "mtrace <source> [group] [receiver]"...
Page 397: Ip Multicast
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.3.2.1 ip multicast This command sets the administrative mode of the IP multicast forwarder in the router to active. For multicast routing to become operational, IGMP must be currently enabled. An error message will be displayed on the CLI if multicast routing is enabled while IGMP is disabled.
Page 398: No Ip Mcast Mroute
Korenix Technology Co., Ltd. Layer 3 Stackable Switch you are creating. < mask > - the subnet mask to be applied to the Source IP address. < rpfipaddr > - the IP address of the neighbor router on the path to the source.
Page 399: Ip Mcast Boundary
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Global Config 8.3.2.4 ip mcast boundary This command adds an administrative scope multicast boundary specified by <groupipaddr> and <mask> for which this multicast administrative boundary is applicable. <groupipaddr> is a group IP address and <mask> is a group IP mask.
Page 400: Mrinfo
Korenix Technology Co., Ltd. Layer 3 Stackable Switch < 0 - 255 > - the TTL threshold. no - This command applies the default <ttlthreshold> to a routing interface. The <ttlthreshold> is the TTL threshold which is to be applied to the multicast Data packets which are to be forwarded from the interface.
Page 401: Mtrace
Korenix Technology Co., Ltd. Layer 3 Stackable Switch is issued. The [<group>] is a multicast address of the group to be displayed. Default value is 224.2.0.1 Syntax mstat <source> [<group>] [<receiver>] < source > - the IP address of the multicast data source.
Page 402: Disable Ip Multicast Mdebug Mtrace
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 239.255.255.255. < destination > - the IP address of the host to which the mtrace response will be sent by the last hop router. Default Setting None Command Mode Privileged Exec 8.3.2.9 disable ip multicast mdebug mtrace This command is used to disable the processing capability of mtrace query on this router.
Page 403: Show Ip Pimdm Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays the system-wide information for PIM-DM. Syntax show ip pimdm Default Setting None Command Mode Privileged Exec Display Message Admin Mode: This field indicates whether PIM-DM is enabled or disabled. This is a configured value.
Page 404: Show Ip Pimdm Interface Stats
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.4.1.3 show ip pimdm interface stats This command displays the statistical information for PIM-DM on the specified interface. Syntax show ip pimdm interface stats {<unit/slot/port> | all} < unit/slot/port > - Interface number.
Page 405: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Setting None Command Mode Privileged Exec Display Message Neighbor Addr: This field displays the IP Address of the neighbor on an interface. Interface: Valid unit, slot and port number separated by forward slashes.
Page 406: Ip Pimdm Query-Interval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ip pimdm mode no ip pimdm mode no - This command sets administrative mode of PIM-DM on an interface to disabled. Default Setting Disabled Command Mode Interface Config 8.4.2.3 ip pimdm query-interval This command configures the transmission frequency of hello messages between PIM enabled neighbors.
Page 407: Show Ip Pimsm Componenttable
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays the system-wide information for PIM-SM. Syntax show ip pimsm Default Setting None Command Mode Privileged Exec Display Message Admin Mode: This field indicates whether PIM-SM is enabled or disabled. This is a configured value.
Page 408: Show Ip Pimsm Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Component Index: This field displays a number which uniquely identifies the component. Component BSR Address: This field displays the IP address of the bootstrap router (BSR) for the local PIM region. Component BSR Expiry Time: This field displays the minimum time remaining before the BSR in the local domain will be declared down.
Page 409: Show Ip Pimsm Neighbor
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command displays the statistical information for PIM-SM on the specified interface. Syntax show ip pimsm interface stats {<unit/slot/port> | all} < unit/slot/port > - Interface number. all - this command represents all interfaces.
Page 410: Show Ip Pimsm Rp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Interface: Valid unit, slot and port number separated by forward slashes. IP Address: This field displays the IP Address of the neighbor on an interface. Up Time: This field indicates the time since this neighbor has become active on this interface.
Page 411: Show Ip Pimsm Rphash
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.5.1.7 show ip pimsm rphash This command displays the RP router that will be selected from the set of active RP routers. The RP router, for the group, is selected by using the hash algorithm defined in RFC 2362.
Page 412: Configuration Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 8.5.2 Configuration Commands 8.5.2.1 ip pimsm This command sets administrative mode of PIM-SM multicast routing across the router to enabled. IGMP must be enabled before PIM-SM can be enabled. Syntax ip pimsm...
Page 413: Ip Pimsm Register-Rate-Limit
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Global Config 8.5.2.3 ip pimsm register-rate-limit This command is used to configure the Threshold rate for the RP router to switch to the shortest path. The rate is specified in Kilobytes per second. The possible values are 0 to 2000.
Page 414: Ip Pimsm Staticrp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Mode Global Config 8.5.2.5 ip pimsm staticrp This command is used to create RP IP address for the PIM-SM router. The parameter <rp-address> is the IP address of the RP. The parameter <group-address> is the group address supported by the RP.
Page 415: Ip Pimsm Query-Interval
Korenix Technology Co., Ltd. Layer 3 Stackable Switch no ip pimsm mode no - This command sets administrative mode of PIM-SM multicast routing on a routing interface to disabled. Default Setting Disbaled Command Mode Interface Config 8.5.2.7 ip pimsm query-interval This command configures the transmission frequency of hello messages in seconds between PIM enabled neighbors.
Page 416: Ip Pimsm Cbsrhashmasklength
Korenix Technology Co., Ltd. Layer 3 Stackable Switch ip pimsm cbsrpreference <-1 - 255> no ip pimsm cbsrpreference <-1 - 255> - The preference value for the local interface. no - This command is used to reset the CBSR preference for a particular PIM-SM interface to the default value.
Page 417 Korenix Technology Co., Ltd. Layer 3 Stackable Switch PIM-SM interface. The valid values are from (-1 to 255), and the value of -1 is used to indicate that the local interface is not a Candidate RP interface. The active router interface, with the highest IP Address and crppreference greater than -1, is chosen as the CRP for the router.
Page 418: Stacking Commands
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 9 Stacking Commands 9.1 show switch This command displays information about all units in the stack. If users run this command in session mode, it only shows the information of the corresponding switch in that session.
Page 419: Show Supported Switchtype
Korenix Technology Co., Ltd. Layer 3 Stackable Switch TPKT: Number of transmitted packets. RFCS: Number of received FCS errors. RFRG: Number of received packets which are undersize and FCS errors. RJBR: Number of received packets which are oversize and FCS errors.
Page 420: Switch Provision
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 9.3 switch provision This command configures a switch. Syntax switch <unit> provision <type> no switch <unit> provision <unit> - Is the switch identifier of the switch to be added/removed from the stack.
Page 421: Switch Renumber
Korenix Technology Co., Ltd. Layer 3 Stackable Switch become a management unit. Note that users can neither set management unit’s priority value to 0 nor set the priority of a provision switch. No – Set priority value to unassigned. Default Setting Unassigned.
Page 422: Archive Copy-Sw
Korenix Technology Co., Ltd. Layer 3 Stackable Switch This command moves the Primary Management Unit functionality from one switch to another. Upon execution, the entire stack (including all interfaces in the stack) will be unconfigured and reconfigured with the configuration on the new Primary Management Unit.
Page 423: Archive Download-Sw
Korenix Technology Co., Ltd. Layer 3 Stackable Switch < unit > - download the run time code to the specified switch ID. Default Setting None. Command Mode Privileged Exec 9.8 archive download-sw This command downloads the code image file to the Primary Management switch and all slave switches in the stack.
Page 424: Session
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Syntax reload [slot <unit>] < unit > - Specify the switch to be reset. Default Setting None. Command Mode Privileged Exec 9.10 session This command provides users to access a specific stack member. Users can show the information of this switch in the stack.
Page 425: Web-Based Management Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10 Web-Based Management Interface 10.1 Overview Your Layer 3 Network Switch provides a built-in browser software interface that lets you configure and manage it remotely using a standard Web browser such as Microsoft Internet Explorer or Netscape Navigator.
Page 426: Main Menu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2 Main Menu 10.2.1 System Menu 10.2.1.1 View ARP Cache The Address Resolution Protocol (ARP) dynamically maps physical (MAC) addresses to Internet (IP) addresses. This panel displays the current contents of the ARP cache.
Page 427 Korenix Technology Co., Ltd. Layer 3 Stackable Switch System Description - The product name of this switch. Machine Type - The machine type of this switch. Machine Model - The model within the machine type. Serial Number - The unique box serial number for this switch.
Page 428: Configuring Management Session And Network Parameters
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.3 Configuring Management Session and Network Parameters 10.2.1.3.1. Viewing System Description Page Configurable Data System Name - Enter the name you want to use to identify this switch. You may use up to 31 alpha-numeric characters.
Page 429 Korenix Technology Co., Ltd. Layer 3 Stackable Switch System Contact - Enter the contact person for this switch. You may use up to 31 alpha-numeric characters. The factory default is blank. Non-Configurable Data System Description - The product name of this switch.
Page 430 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.3.2. Configuring Network Connectivity Page The network interface is the logical interface used for in-band connectivity with the switch via any of the switch's front panel ports. The configuration parameters associated with the switch's network interface do not affect the configuration of the front panel ports through which traffic is switched or routed.
Page 431 Korenix Technology Co., Ltd. Layer 3 Stackable Switch the web page is displayed. Non-Configurable Data Burned-in MAC Address - The burned-in MAC address used for in-band connectivity if you choose not to configure a locally administered address. Command Buttons Submit - Update the switch with the values on the screen. If you want the switch to retain the new values across a power cycle you must perform a save.
Page 432 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.3.4. Configuring Outbound Telnet Client Configuration Page Configurable Data Admin Mode - Specifies if the Outbound Telnet service is Enabled or Disabled. Default value is Enabled. Maximum Sessions - Specifies the maximum number of Outbound Telnet Sessions allowed.
Page 433 Korenix Technology Co., Ltd. Layer 3 Stackable Switch pull-down menu. You may choose from 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200 baud. The factory default is 9600 baud. Password Threshold - When the logon attempt threshold is reached on the console port, the system interface becomes silent for a specified amount of time before allowing the next logon attempt.
Page 434 Korenix Technology Co., Ltd. Layer 3 Stackable Switch User Name Selector - You can use this screen to reconfigure an existing account, or to create a new one. Use this pulldown menu to select one of the existing accounts, or select 'Create' to add a new one, provided the maximum of five 'Read Only' accounts has not been reached.
Page 435 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.3.7. Defining Authentication List Configuration Page You use this screen to configure login lists. A login list specifies the authentication method(s) you want used to validate switch or port access for the users associated with the list. The pre-configured users, admin and guest, are assigned to a pre-configured list named defaultList, which you may not delete.
Page 436 Korenix Technology Co., Ltd. Layer 3 Stackable Switch second in the selected authentication login list. This is the method that will be used if the first method times out. If you select a method that does not time out as the second method, the third method will not be tried.
Page 437 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.3.9. Viewing Authentication List Summary Page Non-Configurable Data Authentication List - Identifies the authentication login list summarized in this row. Method List - The ordered list of methods configured for this login list.
Page 438: Defining Forwarding Database
Korenix Technology Co., Ltd. Layer 3 Stackable Switch authentication via the RADIUS server, you will not need to create an account for all users on each switch. However, by default the 'non-configured user' is assigned to 'defaultList', which by default uses local authentication.
Page 439 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.4.2. Viewing Forwarding Database Page Use this panel to display information about entries in the forwarding database. These entries are used by the transparent bridging function to determine how to forward a received frame.
Page 440: Viewing Logs
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Self: the MAC address of one of the switch's physical interfaces. Command Buttons Search - Search for the specified MAC address. Refresh - Refetch the database and display it again starting with the first entry in the table.
Page 441 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.5.2. Viewing Buffered Log Page This help message applies to the format of all logged messages which are displayed for the buffered log, persistent log, or console log. Format of the messages <15>Aug 24 05:34:05 STK0 MSTP[2110]: mspt_api.c(318) 237 %% Interface 12...
Page 442 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.5.3. Configuring Command Logger Page Configurable Data Admin Mode - Enable/Disable the operation of the CLI Command logging by selecting the corresponding pulldown field and clicking Submit. Command Buttons Submit - Update the switch with the values you entered.
Page 443 Korenix Technology Co., Ltd. Layer 3 Stackable Switch -Emergency (0): system is unusable -Alert (1): action must be taken immediately -Critical (2): critical conditions -Error (3): error conditions -Warning (4): warning conditions -Notice(5): normal but significant conditions -Informational(6): informational messages...
Page 444 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.5.6. Configuring Hosts configuration Page Configurable Data Host - This is a list of the hosts that have been configured for syslog. Select a host for changing the configuration or choose to add a new hosts from the drop down list.
Page 445: Managing Switch Interface
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.5.7. Configuring syslog configuration Page Configurable Data Admin Status -For Enabling and Disabling logging to configured syslog hosts. Setting this to disable stops logging to all syslog hosts. Disable means no messages will be sent to any collector/relay.
Page 446 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.6.1. Configuring Switch Interface Page Selection Criteria Slot/Port - Selects the interface for which data is to be displayed or configured. Configurable Data STP Mode - The Select the Spanning Tree Protocol Administrative Mode for the port or LAG.
Page 447 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 3124 4167 Multicast Storm Control - Used to enable or disable the multicast storm feature on the selected interface. Multicast storm control value could be set Level 1, Level 2, Level 3, and Level 4.
Page 448 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.6.2. Viewing Switch Interface Configuration Page This screen displays the status for all ports in the box. Selection Criteria MST ID - Select the Multiple Spanning Tree instance ID from the list of all currently configured MST ID's to determine the values displayed for the Spanning Tree parameters.
Page 449 Korenix Technology Co., Ltd. Layer 3 Stackable Switch action a port takes on receipt of a frame. If the bridge detects a malfunctioning port it will place that port into the broken state. The other five states are defined in IEEE 802.1D:...
Page 450 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.6.3. Configuring Multiple Port Mirroring Function Page Configurable Data Session ID - A session ID or "All Sessions" option may be selected. By default the First Session is selected. Session Mode - Specifies the Session Mode for a selected session ID. By default Session Mode is enabled.
Page 451: Defining Snmp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.7 Defining SNMP 10.2.1.7.1. Configuring SNMP Community Configuration Page By default, two SNMP Communities exist: private, with 'Read/Write' privileges and status set to enable public, with 'Read Only' privileges and status set to enable These are well-known communities, you can use this menu to change the defaults or to add other communities.
Page 452 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Client IP Mask parameters are 192.168.1.0/255.255.255.0, then any client whose IP address is 192.168.1.0 through 192.168.1.255 (inclusive) will be allowed access. To allow access from only one station, use a Client IP Mask value of 255.255.255.255, and use that machine's IP address for Client IP Address.
Page 453 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Status - Select the receiver's status from the pulldown menu: Enable - send traps to the receiver. Disable - do not send traps to the receiver. Command Buttons Submit - Update the switch with the values on this screen. If you want the switch to retain the new values across a power cycle, you must perform a save.
Page 454: Viewing Statistics
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.8 Viewing Statistics 10.2.1.8.1. Viewing the whole Switch Detailed Statistics Page Non-Configurable Data ifIndex - This object indicates the ifIndex of the interface table entry associated with the Processor of this switch.
Page 455 Korenix Technology Co., Ltd. Layer 3 Stackable Switch higher-layer protocol. A possible reason for discarding a packet could be to free up buffer space. Octets Transmitted - The total number of octets transmitted out of the interface, including framing characters.
Page 456 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Clear Counters - Clear all the counters, resetting all switch summary and detailed statistics to default values. The discarded packets count cannot be cleared. Refresh - Refresh the data on the screen with the present state of the data in the switch.
Page 457 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Address Entries Currently in Use - The total number of Forwarding Database Address Table entries now active on the switch, including learned and static entries. VLAN Entries Currently in Use - The number of VLAN entries presently occupying the VLAN table.
Page 458 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Packets RX and TX 128-255 Octets - The total number of packets (including bad packets) received or transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
Page 459 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Packets Received 512-1023 Octets - The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets). Packets Received 1024-1518 Octets - The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
Page 460 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Total Packets Transmitted (Octets) - The total number of octets of data (including those in bad packets) transmitted on the network (excluding framing bits but including FCS octets). This object can be used as a reasonable estimate of ethernet utilization. If greater precision is desired, the etherStatsPkts and etherStatsOctets objects should be sampled before and after a common interval.
Page 461 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Multicast Packets Transmitted - The total number of packets that higher-level protocols requested be transmitted to a Multicast address, including those that were discarded or not sent. Broadcast Packets Transmitted - The total number of packets that higher-level protocols requested be transmitted to the Broadcast address, including those that were discarded or not sent.
Page 462 Korenix Technology Co., Ltd. Layer 3 Stackable Switch GMRP PDUs Transmitted - The count of GMRP PDUs transmitted from the GARP layer. GMRP Failed Registrations - The number of times attempted GMRP registrations could not be completed. Time Since Counters Last Cleared - The elapsed time, in days, hours, minutes, and seconds since the statistics for this port were last cleared.
Page 463 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.8.4. Viewing Each Port Summary Statistics Page Selection Criteria Slot/Port - Selects the interface for which data is to be displayed or configured. Non-Configurable Data ifIndex - This object indicates the ifIndex of the interface table entry associated with this port on an adapter.
Page 464: Managing System Utilities
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Clear Counters - Clears all the counters, resetting all statistics for this port to default values. Clear All Counters - Clears all the counters for all ports, resetting all statistics for all ports to default values.
Page 465 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.9.3. Restoring All Configuration to Default Values Page Command Buttons Reset - Clicking the Reset button will reset all of the system login passwords to their default values. If you want the switch to retain the new values across a power cycle, you must perform a save.
Page 466 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Code – Specify code when you want to upgrade the operational flash. Configuration - Specify configuration when you want to update the switch's configuration. If the file has errors the update will be stopped.
Page 467 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.9.6. Uploading Specific Files from Switch Flash Page Use this menu to upload a code, configuration, or log file from the switch. Configurable Data File Type - Specify the type of file you want to upload. The available options are Script, Code, CLI Banner, Configuration, Error Log, Buffered Log, and Trap Log.
Page 468 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.9.8. Removing Specific File Page Delete files in flash. If the file type is used for system startup, then this file cannot be deleted. Configurable Data Configuration File - Configuration files. Runtime File - Run-time operation codes.
Page 469 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.9.10. Defining Ping Function Page Use this screen to tell the switch to send a Ping request to a specified IP address. You can use this to check whether the switch can communicate with a particular IP station. Once you click the Submit button, the switch will send three pings and the results will be displayed below the configurable data.
Page 470 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Disable. Command Buttons Submit - Send the updated screen to the switch. Changes take effect on the switch but these changes will not be retained across a power cycle unless a save is performed.
Page 471: Defining Trap Manager
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Clear - Clear all the counters, resetting all switch summary and detailed statistics to default values. The discarded packets count cannot be cleared. Refresh - Refresh the data on the screen with the present state of the data in the switch.
Page 472 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Configurable Data Authentication - Enable or disable activation of authentication failure traps by selecting the corresponding line on the pull down entry field. The factory default is enabled. Link Up/Down - Enable or disable activation of link status traps by selecting the corresponding line on the pull down entry field.
Page 473: Configuring Sntp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Number of Traps since last reset - The number of traps that have occurred since the switch were last reset. Trap Log Capacity - The maximum number of traps stored in the log. If the number of traps exceeds the capacity, the entries will overwrite the oldest entries.
Page 474 Korenix Technology Co., Ltd. Layer 3 Stackable Switch can determine the time and, optionally the round-trip delay and local clock offset relative to the server. • Broadcast - SNTP operates in the same manner as multicast mode but uses a local broadcast address instead of a multicast address.
Page 475 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Supported Mode - Specifies the SNTP modes the client supports. Multiple modes may be supported by a client. Last Update Time - Specifies the local date and time (UTC) the SNTP client last updated the system clock.
Page 476 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.11.3. Configuring SNTP Server Page Configurable Data Server - Specifies all the existing Server Addresses along with an additional option "Create". When the user selects "Create" another text box "Address" appears where the user may enter Address for Server to be configured.
Page 477 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Version - Specifies the NTP Version running on the server. Allowed range is (1 to 4). Default value is 4. Command Buttons Submit - Sends the updated configuration to the switch. Configuration changes take effect immediately.
Page 478 Korenix Technology Co., Ltd. Layer 3 Stackable Switch to be sent to this server. This is indicated by a stratum field equal to 0 in a message received from a server. Unicast Server Num Requests - Specifies the number of SNTP requests made to this server since last time agent reboot.
Page 479 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.11.6. Configuring Time Zone Settings Page Simple Network Time Protocol (SNTP) allows the switch to set its internal clock based on periodic updates from a time server. Maintaining an accurate time on the switch enables the system log to record meaningful dates and times for event entries.
Page 480: Defining Dhcp Client
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.1.12 Defining DHCP Client 10.2.1.12.1. Configuring DHCP Restart Page This command issues a BOOTP or DHCP client request for any IP interface that has been set to BOOTP or DHCP mode via the IP address command. DHCP requires the server to reassign the client's last address if available.
Page 481: Switching Menu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2 Switching Menu 10.2.2.1 Managing Port-based VLAN 10.2.2.1.1. Configuring Port-based VLAN Configuration Page Selection Criteria VLAN ID and Name - You can use this screen to reconfigure an existing VLAN, or to create a new one.
Page 482 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Slot/Port - Indicates which port is associated with the fields on this line. Status - Indicates the current value of the participation parameter for the port. Command Buttons Submit - Update the switch with the values on this screen. If you want the switch to retain the new values across a power cycle, you must perform a save.
Page 483 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.1.2. Viewing Port-based VLAN Information Page This page displays the status of all currently configured VLANs. VLAN ID - The VLAN Identifier (VID) of the VLAN. The range of the VLAN ID is (1 to 3965).
Page 484 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.1.4. Viewing VLAN Port Summary Page Non-Configurable Data Slot/Port - The interface. Port VLAN ID - The VLAN ID that this port will assign to untagged frames or priority tagged frames received on this port.
Page 485 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.1.5. Resetting VLAN Configuration Page Command Buttons Reset - If you select this button and confirm your selection on the next screen, all VLAN configuration parameters will be reset to their factory default values. Also, all VLANs, except for the default VLAN, will be deleted.
Page 486: Managing Protocol-Based Vlan
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.2 Managing Protocol-based VLAN 10.2.2.2.1. Protocol-based VLAN Configuration Page You can use a protocol-based VLAN to define filtering criteria for untagged packets. By default, if you do not configure any port- (IEEE 802.1Q) or protocol-based VLANs, untagged packets will be assigned to VLAN 1.
Page 487 Korenix Technology Co., Ltd. Layer 3 Stackable Switch VLAN - VLAN can be any number in the range of (1 to 3965) . All the ports in the group will assign this VLAN ID to untagged packets received for the protocols you included in this group.
Page 488: Defining Garp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch maps network layer addresses to physical medium access control (MAC) addresses. IPX - The Internetwork Packet Exchange (IPX) is a connectionless datagram Network-layer protocol that forwards data over a network. VLAN - The VLAN ID associated with the group.
Page 489 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Leave All Time (centiseconds) -This Leave All Time controls how frequently LeaveAll PDUs are generated. A LeaveAll PDU indicates that all registrations will shortly be deregistered. Participants will need to rejoin in order to maintain registration. An instance of this timer exists for each GARP participant for each port.
Page 490 Korenix Technology Co., Ltd. Layer 3 Stackable Switch the switch by selecting enable or disable from the pull down menu. The factory default is disabled. Command Buttons Submit - Update the switch with the values you entered. If you want the switch to retain the new values across a power cycle you must perform a save.
Page 491: Managing Igmp Snooping
Korenix Technology Co., Ltd. Layer 3 Stackable Switch seconds). The factory default is 1000 centiseconds (10 seconds). An instance of this timer exists for each GARP participant for each port. Command Buttons Submit - Update the switch with the values you entered. If you want the switch to retain the new values across a power cycle you must perform a save.
Page 492 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Submit - Update the switch with the values you entered. If you want the switch to retain the new values across a power cycle you must perform a save. You will only see this button if you have Read/Write access privileges.
Page 493 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Submit - Update the switch with the values you entered. If you want the switch to retain the new values across a power cycle you must perform a save. You will only see this button if you have Read/Write access privileges.
Page 494 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.4.4. Configuring IGMP Snooping VLAN Page Configurable Data VLAN ID - Specifies list of VLAN IDs for which IGMP Snooping is enabled. VLAN ID - Appears when "New Entry" is selected in VLAN ID combo box. Specifies VLAN ID for which pre-configurable Snooping parameters are to be set.
Page 495 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Refresh - Refetch the database and display it again starting with the first entry in the table. 10.2.2.4.6. Configuring Multicast Router Page Configurable Data Unit/Slot/Port - The select box lists all Unit/Slot/Ports. Select the interface for which you want Multicast Router to be enabled .
Page 496 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.4.8. Configuring Multicast Router VLAN Page Selection Criteria Unit/Slot/Port - The select box lists all Unit/Slot/Ports.Select the interface for which you want Multicast Router to be enabled. Configurable Data VLAN ID - VLAN ID for which the Multicast Router Mode is to be Enabled or Disabled.
Page 497 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 00:00:00:00:00:00 01:00:5E:00:00:01 to 01:00:5E:00:00:FF FF:FF:FF:FF:FF:FF VLAN ID - The VLAN ID used with the MAC address to fully identify packets you want L2Mcast Group. You can only change this field when you have selected the "Create Filter"...
Page 498 Korenix Technology Co., Ltd. Layer 3 Stackable Switch MAC Address Search - You may also search for an individual L2Mcast address. Enter the six byte hexadecimal MAC address, for example 01:00:5E:00:11:11. VLAN - You also have to give a VLAN ID you want with L2Mcast address.
Page 499: Managing Port-Channel
Korenix Technology Co., Ltd. Layer 3 Stackable Switch will be displayed. Dynamic: If you choose "Static" only L2Mcast router port(s) that have been configured will be displayed. All: If you choose "all" the whole table will be displayed. VLAN - You also have to give a VLAN ID you want with L2Mcast router port.
Page 500 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.5.2. Configuring Port-Channel Configuration Page Selection Criteria Port Channel Name – You can use this screen to reconfigure an existing Port Channel, or to create a new one. Use this pull down menu to select one of the existing Port Channels, or select 'Create' to add a new one.
Page 501 Korenix Technology Co., Ltd. Layer 3 Stackable Switch default VLAN. This field will not appear when a new Port Channel is being created. Refresh - Refresh the data on the screen with the present state of the data in the switch.
Page 502: Viewing Multicast Forwarding Database
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Enable - spanning tree is enabled for this Port Channel. Link Trap - Whether or not a trap will be sent when link status changes. The factory default is enabled. Configured Ports - A list of the ports that are members of the Port Channel, in Slot/Port notation.
Page 503 Korenix Technology Co., Ltd. Layer 3 Stackable Switch protocol. Component - This is the component that is responsible for this entry in the Multicast Forwarding Database. Possible values are IGMP Snooping, GMRP, and Static Filtering. Description - The text description of this multicast table entry. Possible values are Management Configured, Network Configured, and Network Assisted.
Page 504 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.6.3. Viewing IGMP Snooping MFDB Table Page Non-Configurable Data MAC Address - A VLAN ID - multicast MAC address pair for which the switch has forwarding and/or filtering information. The format is 8 two-digit hexadecimal numbers that are separated by colons, for example 00:01:23:45:67:89:AB:CD.
Page 505: Managing Spanning Tree
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.7 Managing Spanning Tree 10.2.2.7.1. Configuring Switch Spanning Tree Configuration Page Configurable Data Spanning Tree Mode - Specifies whether spanning tree operation is enabled on the switch. Value is enabled or disabled Force Protocol Version - Specifies the Force Protocol Version parameter for the switch.
Page 506 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.7.2. Configuring Spanning Tree CST Configuration Page Configurable Data Bridge Priority - Specifies the bridge priority for the Common and Internal Spanning tree (CST). The value lies between 0 and 61440. It is set in multiples of 4096. For example, if you set the priority to any value between 0 and 4095, it will be set to 0.
Page 507 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Root Port - Port to access the Designated Root for the CST. Max Age - Path Cost to the Designated Root for the CST. Forward Delay - Derived value of the Root Port Bridge Forward Delay parameter.
Page 508 Korenix Technology Co., Ltd. Layer 3 Stackable Switch MST ID - This is only visible when the select option of the MST ID select box is selected. The ID of the MST being created. Valid values for this are between 1 and 4054.
Page 509 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.7.4. Configuring each Port CST Configuration Page Selection Criteria Slot/Port - Selects one of the physical or LAG interfaces associated with VLANs associated with the CST. Configurable Data Port Priority - The priority for a particular port within the CST. The port priority is set in multiples of 16.
Page 510 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Alternate Port, Backup Port, Master Port, or Disabled Port. Designated Root - Root Bridge for the CST. It is made up using the bridge priority and the base MAC address of the bridge.
Page 511 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.7.5. Configuring each Port MST Configuration Page Selection Criteria MST ID - Selects one MST instance from existing MST instances. Slot/Port - Selects one of the physical or LAG interfaces associated with VLANs associated with the selected MST instance.
Page 512 Korenix Technology Co., Ltd. Layer 3 Stackable Switch the LAN. It is made up from the port priority and the interface number of the port. Command Buttons Submit - Applies the new configuration and causes the changes to take effect. These changes will not be retained across a power cycle unless a save configuration is performed.
Page 513: Defining 802.1P Priority
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.8 Defining 802.1p priority 10.2.2.8.1. Defining 802.1p Priority Mapping Page Selection Criteria Slot/Port - Select the physical interface for which you want to display or configure data. Select 'All' to set the parameters for all ports to the same values.
Page 514: Managing Port Security
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.9 Managing Port Security 10.2.2.9.1. Configuring Port Security Administration Mode Page Configurable Data Allow Port Security - Used to enable or disable the Port Security feature. Command Buttons Submit - Applies the new configuration and causes the changes to take effect. These changes will not be retained across a power cycle unless a save configuration is performed.
Page 515 Korenix Technology Co., Ltd. Layer 3 Stackable Switch designating when a packet with a disallowed MAC address is received on a locked port. Command Buttons Submit - Applies the new configuration and causes the changes to take effect. These changes will not be retained across a power cycle unless a save configuration is performed.
Page 516 Korenix Technology Co., Ltd. Layer 3 Stackable Switch the Static list. Command Buttons Submit - Applies the new configuration and causes the changes to take effect. These changes will not be retained across a power cycle unless a save configuration is performed.
Page 517: Managing Lldp (Link Layer Discovery Protocol)
Korenix Technology Co., Ltd. Layer 3 Stackable Switch was discarded at a locked port. VLAN ID - Displays the VLAN ID corresponding to the Last Violation MAC address. 10.2.2.10 Managing LLDP (Link Layer Discovery Protocol) 10.2.2.10.1. Global Configuration Use this panel to configure the LLDP global configuration.
Page 518 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Receive: Enabel receive LLDPDUs on the selected interface. Notify: Enabel “Send remote data change notification” on the selected interface. Mgmt: Select to enable the interface transmits system management address information in the LLDPDUs.
Page 519 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.2.10.4. LLDP Statistics Use this page to see the LLDP statistic. Non-configurable data Last Update: Shows the amount of time since the last update to the remote table in days, hours, minutes, and seconds.
Page 520 Korenix Technology Co., Ltd. Layer 3 Stackable Switch The interface table contains the following column headings: Interface: Shows the interface in slot/port format. Transmit Total: Total number of LLDP packets transmitted on the port. Receive Total: Total number of LLDP packets received on the port.
Page 521 Korenix Technology Co., Ltd. Layer 3 Stackable Switch agent uses to send and receive information. ……………. 10.2.2.10.6. Local Device Summary Use this panel to display the interface’s LLDP local device Summary. Selection Criteria Unit/Slot/Port - Select the physical interface for which you want to configure. You can select one specific port or apply to all ports.
Page 522 Korenix Technology Co., Ltd. Layer 3 Stackable Switch enabled. Management Address: Lists the type of address and the specific address the local LLDP agent uses to send and receive information. ……………. 10.2.2.10.8. Remote Device Summary Use this panel to display the interface’s LLDP remote device Summary.
Page 523: Routing Menu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3 Routing Menu 10.2.3.1 Managing ARP Table 10.2.3.1.1. Creating ARP entries Use this panel to add an entry to the Address Resolution Protocol table. Configurable Data IP - Specifies all the existing static ARP along with an additional option "Create". When the user selects "Create"...
Page 524 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Response Time - Enter the value you want the switch to use for the ARP response timeout. You must enter a valid integer, which represents the number of seconds the switch will wait for a response to an ARP request. The range for this field is 1 to 10 seconds.
Page 525: Managing Ip Interfaces
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Unit/Slot/Port - The routing interface associated with the ARP entry. Type - The type of the ARP entry: Local - An ARP entry associated with one of the switch's routing interface's MAC...
Page 526 Korenix Technology Co., Ltd. Layer 3 Stackable Switch IP Forwarding Mode - Select enable or disable from the pulldown menu. This enables or disables the forwarding of IP frames. The default value is enable. Non-Configurable Data Default Time to Live - The default value inserted into the Time-To-Live field of the IP header of datagrams originated by the switch, if a TTL value is not supplied by the transport layer protocol.
Page 527 Korenix Technology Co., Ltd. Layer 3 Stackable Switch include only those packets which were Source-Routed via this entity, and the Source-Route option processing was successful. IpInUnknownProtos - The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
Page 528 Korenix Technology Co., Ltd. Layer 3 Stackable Switch IpRoutingDiscards - The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries.
Page 529 Korenix Technology Co., Ltd. Layer 3 Stackable Switch IcmpOutEchos - The number of ICMP Echo (request) messages sent. IcmpOutEchoReps - The number of ICMP Echo Reply messages sent. IcmpOutTimestamps - The number of ICMP Timestamp (request) messages. IcmpOutTimestampReps - The number of ICMP Timestamp Reply messages sent.
Page 530 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.2.3. Configuring IP Interfaces Selection Criteria Unit/Slot/Port - Select the interface for which data is to be displayed or configured. Configurable Data IP Address - Enter the IP address for the interface.
Page 531: Managing Ospf
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Submit - Update the switch with the values on this screen. If you want the switch to retain the new values across a power cycle, you must perform a save.
Page 532 Korenix Technology Co., Ltd. Layer 3 Stackable Switch advertising the same destination. If you select enable, the preference rules will be those defined by RFC 1583. If you select disable, the preference rules will be those defined in Section 16.4.1 of the OSPF-2 standard (RFC 2328), which will prevent routing loops when AS-external-LSAs for the same destination have been originated from different areas.
Page 533 Korenix Technology Co., Ltd. Layer 3 Stackable Switch LSAs Received - The number of LSAs (link state advertisements) received that were determined to be new instantiations. This number does not include newer instantiations of self-originated LSAs. Command Buttons Submit - Send the updated configuration to the switch. Configuration changes take effect immediately.
Page 534 Korenix Technology Co., Ltd. Layer 3 Stackable Switch OSPF Metric - Regular OSPF metric Comparable Cost - External Type 1 metrics that are comparable to the OSPF metric Non-comparable Cost - External Type 2 metrics that are assumed to be larger than the cost of the OSPF metric Translator Role - Select Always or Candidate from the pulldown menu.
Page 535 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Mode - This field tells you whether the area is or is not a stub area. If the area may be a stub area, a 'Create Stub Area' button will be displayed. If you have configured the area as a stub area a 'Delete Stub Area' button will be displayed.
Page 536 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.3.3. Viewing Stub Area Summary Information Non-Configurable Data Area ID - The Area ID of the Stub area Type of Service - The type of service associated with the stub metric. The switch supports Normal only.
Page 537 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.3.4. Configuring Area Range Selection Criteria Area ID - Selects the area for which data is to be configured. Configurable Data IP address - Enter the IP Address for the address range for the selected area.
Page 538 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.3.5. View Interface Statistics This panel displays statistics for the selected interface. The information will be displayed only if OSPF is enabled. Selection Criteria Unit/Slot/Port - Select the interface for which data is to be displayed.
Page 539 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Originate New LSAs - The number of new link-state advertisements that have been originated. In any given OSPF area, a router will originate several LSAs. Each router originates a router-LSA. If the router is also the Designated Router for any of the area's networks, it will originate network-LSAs for those networks.
Page 540 Korenix Technology Co., Ltd. Layer 3 Stackable Switch network . *NOTE: once OSPF is initialized on the router, it will remain initialized until the router is reset. OSPF Area ID - Enter the 32 bit integer in dotted decimal format that uniquely identifies the OSPF area to which the selected router interface connects.
Page 541 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Authentication Key - Enter the OSPF Authentication Key for the specified interface. If you do not choose to use authentication you will not be prompted to enter a key. If you choose 'simple' authentication you cannot use a key of more than 8 octets. If you choose 'encrypt' the key may be up to 16 octets long.
Page 542 Korenix Technology Co., Ltd. Layer 3 Stackable Switch attached to the network. The Backup Designated Router performs slightly different functions during the Flooding Procedure, as compared to the Designated Router. Other Designated Router - The interface is connected to a broadcast or NBMA network on which other routers have been selected to be the Designated Router and Backup Designated Router either.
Page 543 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.3.7. Viewing Neighbor Table Information This panel displays the OSPF neighbor table list. When a particular neighbor ID is specified, detailed information about a neighbor is given. The information below will only be displayed if OSPF is enabled.
Page 544 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.3.8. Configuring OSPF Neighbor This panel displays the OSPF neighbor configuration for a selected neighbor ID. When a particular neighbor ID is specified, detailed information about a neighbor is given. The information below will only be displayed if OSPF is enabled and the interface has a neighbor.
Page 545 Korenix Technology Co., Ltd. Layer 3 Stackable Switch adjacencies are fully capable of transmitting and receiving all types of OSPF routing protocol packets. Loading - In this state, Link State Request packets are sent to the neighbor asking for the more recent LSAs that have been discovered (but not yet received) in the Exchange state.
Page 546 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Area ID - The ID of an OSPF area to which one of the router interfaces is connected. An Area ID is a 32 bit integer in dotted decimal format that uniquely identifies the area to which an interface is connected.
Page 547 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.3.10. Configuring OSPF Virtual Link Selection Criteria Create New Virtual Link - Select this option from the dropdown menu to define a new virtual link. The area portion of the virtual link identification is fixed: you will be prompted to enter the Neighbor Router ID on a new screen.
Page 548 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Authentication Key - Enter the OSPF Authentication Key for the specified interface. If you do not choose to use authentication you will not be prompted to enter a key. If you choose 'simple' authentication you cannot use a key of more than 8 octets. If you choose 'encrypt' the key may be up to 16 octets long.
Page 549 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Delete - Removes the specified virtual link from the router configuration. 10.2.3.3.11. Viewing OSPF Virtual Link Summary Table Non-Configurable Data Area ID - The Area ID portion of the virtual link identification for which data is to be displayed.
Page 550 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Retransmit Interval - The OSPF retransmit interval for the virtual link in units of seconds. This specifies the time between link-state advertisements for adjacencies belonging to this router interface. This value is also used when retransmitting database descriptions and link-state request packets.
Page 551 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Tag - Sets the tag field in routes redistributed. This field displays the tag if the source was pre-configured, otherwise 0 and can be modified. The valid values are 0 to 4294967295.
Page 552: Managing Bootp/Dhcp Relay Agent
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.3.13. Viewing OSPF Route Redistribution Summary Information This screen displays the OSPF Route Redistribution Configurations. Non Configurable Data Source - The Source Route to be Redistributed by OSPF. Metric- The Metric of redistributed routes for the given Source Route. Display "Unconfigured"...
Page 553 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Admin Mode - Select enable or disable from the pulldown menu. When you select 'enable' BOOTP/DHCP requests will be forwarded to the IP address you entered in the 'Server IP address' field.
Page 554: Managing Dns Relay
Korenix Technology Co., Ltd. Layer 3 Stackable Switch client was powered up. Packets will only be forwarded when the time stamp exceeds the minimum wait time. Circuit Id Option Mode - This is the Relay agent option which can be either enabled or disabled.
Page 555 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Domain Name - Default domain name used to complete unqualified host names. Do not include the initial period that separates an unqualified name from the domain name. This is a text string of up to 64 characters.
Page 556 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.5.3. Configuring Name Server You can use this panel to change the configuration parameters for the domain name servers. You can also use this screen to display the contents of the table.
Page 557 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.5.4. Viewing DNS Cache Summary Information The Domain Name System (DNS) dynamically maps domain name to Internet (IP) addresses. This panel displays the current contents of the DNS cache. Non-Configurable Data Domain Name List - The domain name associated with this record.
Page 558: Managing Routing Information Protocol (Rip)
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Submit - Sends the updated configuration to the switch. Configuration changes take effect immediately. Delete - Deletes the host entry. Sends the updated configuration to the switch. Configuration changes take effect immediately.
Page 559 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Default Metric - Sets a default for the metric of redistributed routes.This field displays the default metric if one has already been set or blank if not configured earlier. The valid values are (1 to 15)
Page 560 Korenix Technology Co., Ltd. Layer 3 Stackable Switch RIP-2 - only RIP version 2 formatted packets will be received. Both - packets will be received in either format. None - no RIP control packets will be received. The default is Both.
Page 561 Korenix Technology Co., Ltd. Layer 3 Stackable Switch RIP version 1 or version 1c on an interface, you must first enable network directed broadcast mode on the corresponding interface. The default value is disabled. Authentication Type - You may select an authentication type other than none by clicking on the 'Configure Authentication' button.
Page 562 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.6.4. Configuring Route Redistribution Configuration This screen can be used to configure the RIP Route Redistribution parameters. The allowable values for each field are displayed next to the field. If any invalid values are entered, an alert message will be displayed with the list of all the valid values.
Page 563 Korenix Technology Co., Ltd. Layer 3 Stackable Switch The default is Internal. Distribute List - Distribute List - Sets the Access List that filters the routes to be redistributed by the destination protocol. Only permitted routes are redistributed. If this command refers to a non-existent access list, all routes are permitted.
Page 564 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.6.5. Viewing Route Redistribution Configuration This screen displays the RIP Route Redistribution Configurations. Non Configurable Data Source - The Source Route to be Redistributed by RIP. Metric- The Metric of redistributed routes for the given Source Route. Displays "Unconfigured"...
Page 565: Managing Router Discovery
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.7 Managing Router Discovery 10.2.3.7.1. Configuring Router Discovery Selection Criteria Unit/Slot/Port - Select the router interface for which data is to be configured. Configurable Data Advertise Mode - Select enable or disable from the pulldown menu. If you select enable, Router Advertisements will be transmitted from the selected interface.
Page 566 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.7.2. Viewing Router Discovery Status Non-Configurable Data Unit/Slot/Port - The router interface for which data is displayed. Advertise Mode - The values are enable or disable. Enable denotes that Router Discovery is enabled on that interface.
Page 567: Managing Route Table
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.8 Managing Route Table 10.2.3.8.1. Viewing Router Route Table Non-Configurable Data Network Address - The IP route prefix for the destination. Subnet Mask - Also referred to as the subnet/network mask, this indicates the portion of the IP interface address that identifies the attached network.
Page 568 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Next Hop IP Address - The outgoing router IP address to use when forwarding traffic to the next router (if any) in the path towards the destination. The next router will always be one of the adjacent neighbors or the IP address of the local interface for a directly attached network.
Page 569 Korenix Technology Co., Ltd. Layer 3 Stackable Switch the next router (if any) in the path towards the destination. The next router will always be one of the adjacent neighbors or the IP address of the local interface for a directly attached network.
Page 570 Korenix Technology Co., Ltd. Layer 3 Stackable Switch BGP4Local Next Hop Unit/Slot/Port - The outgoing router interface to use when forwarding traffic to the destination. Next Hop IP Address - The outgoing router IP address to use when forwarding traffic to the next router (if any) in the path towards the destination.
Page 571 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Add Route - Go to a separate page where a route can be created. 10.2.3.8.5. Configuring Router Route Preference Use this panel to configure the default preference for each protocol (e.g. 60 for static routes, 170 for BGP).
Page 572: Managing Vlan Routing
Korenix Technology Co., Ltd. Layer 3 Stackable Switch RIP - The RIP route preference value in the router. The default value is 15. The range is 1 to 255. Non-Configurable Data Local - This field displays the local route preference value.
Page 573 Korenix Technology Co., Ltd. Layer 3 Stackable Switch immediately. These changes will not be retained across a power cycle unless a save is performed. Delete - Remove the VLAN Routing Interface specified in the VLAN ID input field from the router configuration.
Page 574: Managing Vrrp
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.10 Managing VRRP 10.2.3.10.1. Configuring VRRP Configurable Data VRRP Admin Mode - This sets the administrative status of VRRP in the router to active or inactive. Select enable or disable from the pulldown menu. The default is disable.
Page 575 Korenix Technology Co., Ltd. Layer 3 Stackable Switch VRID - This field is only configurable if you are creating new Virtual Router, in which case enter the VRID in the range 1 to 255 . Unit/Slot/Port - This field is only configurable if you are creating new Virtual Router, in which case select the Unit/Slot/Port for the new Virtual Router from the pulldown menu.
Page 576 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.3.10.3. Viewing Virtual Router Status Non-Configurable Data VRID - Virtual Router Identifier. Unit/Slot/Port - Indicates the interface associate with the VRID. Priority - The priority value used by the VRRP router in the election for the master virtual router.
Page 577 Korenix Technology Co., Ltd. Layer 3 Stackable Switch VMAC Address - The virtual MAC Address associated with the Virtual Router, composed of a 24 bit organizationally unique identifier, the 16 bit constant identifying the VRRP address block and the 8 bit VRID.
Page 578 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Router VRID Errors - The total number of VRRP packets received with an invalid VRID for this virtual router. VRID - the VRID for the selected Virtual Router. Unit/Slot/Port - The Unit/Slot/Port for the selected Virtual Router.
Page 579: Security Menu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4 Security Menu 10.2.4.1 Managing Access Control (802.1x) 10.2.4.1.1. Defining Access Control Page Configurable Data Administrative Mode - This selector lists the two options for administrative mode: enable and disable. The default value is disabled.
Page 580 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.1.2. Configuring each Port Access Control Configuration Page Selection Criteria Port - Selects the port to be configured. When the selection is changed, a screen refresh will occur causing all fields to be updated for the newly selected port. All physical interfaces are valid.
Page 581 Korenix Technology Co., Ltd. Layer 3 Stackable Switch a value in the range of 1 to 65535. The default value is 30. Changing the value will not change the configuration until the Submit button is pressed. Maximum Requests - This input field allows the user to enter the maximum requests for the selected port.
Page 582 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.1.3. Viewing each Port Access Control Configuration Information Page Selection Criteria Port - Selects the port to be displayed. When the selection is changed, a screen refresh will occur causing all fields to be updated for the newly selected port. All physical interfaces are valid.
Page 583 Korenix Technology Co., Ltd. Layer 3 Stackable Switch and Authenticator. This affects whether the unauthorized controlled port exerts control over communication in both directions (disabling both incoming and outgoing frames) or just in the incoming direction (disabling only the reception of incoming frames). This field is not configurable on some platforms.
Page 584 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.1.4. Viewing Access Control Summary Page Non-Configurable Data Port - Specifies the port whose settings are displayed in the current table row. Control Mode - This field indicates the configured control mode for the port. Possible...
Page 585 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.1.5. Viewing each Port Access Control Statistics Page Selection Criteria Port - Selects the port to be displayed. When the selection is changed, a screen refresh will occur causing all fields to be updated for the newly selected port. All physical interfaces are valid.
Page 586 Korenix Technology Co., Ltd. Layer 3 Stackable Switch frames that have been received by this authenticator. EAP Response Frames Received - This displays the number of valid EAP response frames (other than resp/id frames) that have been received by this authenticator.
Page 587 Korenix Technology Co., Ltd. Layer 3 Stackable Switch performed. Refresh - Update the information on the page. 10.2.4.1.7. Defining each Port Access Privileges Page Selection Criteria Port - Selects the port to configure. Configurable Data Users - Selects the users that have access to the specified port or ports.
Page 588: Managing Radius
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.2 Managing RADIUS 10.2.4.2.1. Configuring RADIUS Configuration Page Configurable Data Max Number of Retransmits - The value of the maximum number of times a request packet is retransmitted. The valid range is 1 - 15. Consideration to maximum delay time should be given when configuring RADIUS maxretransmit and RADIUS timeout.
Page 589 Korenix Technology Co., Ltd. Layer 3 Stackable Switch RADIUS servers are configured, the max retransmit value on each will be exhausted before the next server is attempted. A retransmit will not occur until the configured timeout value on that server has passed without a response from the RADIUS server. Therefore, the maximum delay in receiving a response from the RADIUS application equals the sum of (retransmit times timeout) for all configured servers.
Page 590 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Refresh - Update the information on the page. 10.2.4.2.3. Configuring RADIUS Server Configuration Page Selection Criteria RADIUS Server IP Address - Selects the RADIUS server to be configured. Select add to add a server.
Page 591 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.2.4. Viewing RADIUS Server Statistics Page Selection Criteria RADIUS Server IP Address - Selects the IP address of the RADIUS server for which to display statistics. Non-Configurable Data Round Trip Time (secs) - The time interval, in hundredths of a second, between the most recent Access-Reply/Access-Challenge and the Access-Request that matched it from this RADIUS authentication server.
Page 592 Korenix Technology Co., Ltd. Layer 3 Stackable Switch authentication port and dropped for some other reason. Command Buttons Refresh - Update the information on the page. 10.2.4.2.5. Defining RADIUS Accounting Server Configuration Page Selection Criteria Accounting Server IP Address - Selects the accounting server for which data is to be displayed or configured.
Page 593 Korenix Technology Co., Ltd. Layer 3 Stackable Switch only available to READWRITE users. These changes will not be retained across a power cycle unless a save is performed. Refresh - Update the information on the page. 10.2.4.2.6. Viewing RADIUS Accounting Server Statistics Page...
Page 594: Defining Tacacs Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.2.7. Resetting All RADIUS Statistics Page Command Buttons Clear All RADIUS Statistics - This button will clear the accounting server, authentication server, and RADIUS statistics. 10.2.4.3 Defining TACACS Configuration 10.2.4.3.1. Configuring TACACS Configuration Page Use this menu to configure the parameters for TACACS+, which is used to verify the login user's authentication.
Page 595: Defining Ip Filter Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Server Time Out - Timeout value of TACACS+ packet transmit. Retry Count - Retry count after transmit timeout. Status - The TACACS+ server status which are "disable”, “master" and "slave". Share Secret - The key only transmit between TACACS+ client and server..
Page 596: Defining Secure Http Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.5 Defining Secure Http Configuration 10.2.4.5.1. Secure HTTP Configuration Page Configurable Data Admin Mode - This field is used to enable or disable the Administrative Mode of Secure HTTP. The currently configured value is shown when the web page is displayed. The default value is disabled.
Page 597: Defining Secure Shell Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.4.6 Defining Secure Shell Configuration 10.2.4.6.1. Configuring Secure Shell Configuration Page Configurable Data Admin Mode - This select field is used to Enable or Disable the administrative mode of SSH. The currently configured value is shown when the web page is displayed. The default value is Disable.
Page 598: Qos Menu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch these changes will not be retained across a power cycle unless a save is performed. Download Host Keys - Link to the File Transfer page for the Host Key download. Note that to download SSH key files SSH must be administratively disabled and there can be no active SSH sessions.
Page 599 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Submit - Send the updated configuration to the switch. Configuration changes take effect immediately. These changes will not be retained across a power cycle unless a save is performed. Delete - Removes the currently selected IP ACL from the switch configuration.
Page 600 Korenix Technology Co., Ltd. Layer 3 Stackable Switch selected to configure rules for. The rule identification, and the 'Action' and 'Match Every' parameters must be specified next. If 'Match Every' is set to false a new screen will then be presented from which the match criteria can be configured.
Page 601 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Source IP Mask - Specify the IP Mask in dotted-decimal notation to be used with the Source IP Address value. Source L4 Port Keyword - Specify a packet's source layer 4 port as a match condition for the selected extended IP ACL rule.
Page 602 Korenix Technology Co., Ltd. Layer 3 Stackable Switch The IP TOS field in a packet is defined as all eight bits of the Service Type octet in the IP header. The TOS Bits value is a hexadecimal number from 00 to FF. The TOS Mask value is a hexadecimal number from 00 to FF.
Page 603 Korenix Technology Co., Ltd. Layer 3 Stackable Switch MAC ACL Name - Specifies MAC ACL Name string which may include alphabetic, numeric, dash, underscore or space characters only. The name must start with an alphabetic character. This field displays the name of the currently selected MAC ACL if the ACL has already been created.
Page 604 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.5.1.6. Configuring MAC Access Control List Rule Configuration Page Selection Criteria MAC ACL - Select the MAC ACL for which to create or update a rule. Rule - Select an existing rule or select 'Create New Rule' to add a new Rule. New rules cannot be created if the maximum number of rules has been reached.
Page 605 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Novell PPPoE Reverse ARP User Value Ethertype User Value - Specifies the user defined customised Ethertype value to be used when the user has selected "User Value" as Ethertype Key, to compare against an Ethernet frame.
Page 606 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Direction - Specifies the packet filtering direction for ACL. Valid Directions Inbound ACL Type - Specifies the type of ACL. Valid ACL Types IP ACL MAC ACL IP ACL - Specifies list of all IP ACLs. This field is visible only if the user has selected "IP ACL"...
Page 607: Managing Differentiated Services
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.5.2 Managing Differentiated Services 10.2.5.2.1. Defining DiffServ Configuration Page Operation Packets are filtered and processed based on defined criteria. The filtering criteria is defined by a class. The processing is defined by a policy's attributes. Policy attributes may be defined on a per-class instance basis, and it is these attributes that are applied when a match occurs.
Page 608 Korenix Technology Co., Ltd. Layer 3 Stackable Switch the policy class instances) out of the total allowed on the switch. Service table - Displays the number of configured services (attached to the policies on specified interfaces) out of the total allowed on the switch.
Page 609 Korenix Technology Co., Ltd. Layer 3 Stackable Switch class of the same type. Moreover, a 'Remove Class Reference' button appears on the screen that can be invoked to remove the current class reference. Configurable Data Class Name - This is a case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying a class.
Page 610 Korenix Technology Co., Ltd. Layer 3 Stackable Switch based on the selection of this field. If an existing policy is selected then the screen will display Member Classes for that DiffServ policy. If 'create' is selected, another screen appears to facilitate creation of a new policy. The default is 'create'.
Page 611 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.5.2.6. Configuring DiffServ Policy Class Definition Page Selection Criteria Policy Selector - This lists all the existing DiffServ policy names, from which one can be selected. Member Class List - This lists all existing DiffServ classes currently defined as members of the specified Policy, from which one can be selected.
Page 612 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.5.2.8. Configuring DiffServ Service Configuration Page Selection Criteria Slot/Port - Select the Slot/Port that uniquely specifies an interface. This is a list of all valid slot number and port number combinations in the system. For Read/Write users where 'All' appears in the list, select it to specify all interfaces.
Page 613 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Policy Name - Shows the name of the attached policy. 10.2.5.2.10. Viewing DiffServ Service Statistics Page This screen displays service-level statistical information in tabular form for all interfaces in the system to which a DiffServ policy has been attached in the inbound and/or outbound traffic directions.
Page 614: Configuring Diffserv Wizard Page
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Direction - List of the traffic direction of interface. Only shows the direction(s) for which a DiffServ policy is currently attached. Member Classes - List of all DiffServ classes currently defined as members of the selected Policy Name.
Page 615: Managing Class Of Service
Korenix Technology Co., Ltd. Layer 3 Stackable Switch High - sets policing action to markdscp ef. Med - sets policing action to markdscp af31. Low - sets policing action to send. If Policing is set to NO, then all traffic will be marked as specified below: High - sets policy mark ipdscp ef.
Page 616 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.5.4.1. Managing Table Configuration Page Selection Criteria Unit/Slot/Port - Specifies all CoS configurable interfaces. The option "Global" represents the most recent global configuration settings. These may be overridden on a per-interface basis.
Page 617 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.5.4.2. Configuring CoS interface Selection Criteria Unit/Slot/Port - Specifies all CoS configurable interfaces. The option "Global" represents the most recent global configuration settings. These may be overridden on a per-interface basis. Configurable Data Interface Shaping Rate - Specifies the maximum bandwidth allowed, typically used to shape the outbound transmission rate.
Page 618 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Submit - Send the updated configuration to the switch. Configuration changes take effect immediately. These changes will not be retained across a power cycle unless a save is performed. 10.2.5.4.3. Configuring CoS interface queue Selection Criteria Unit/Slot/Port - Specifies all CoS configurable interfaces.
Page 619 Korenix Technology Co., Ltd. Layer 3 Stackable Switch taildrop Default value is taildrop. Command Buttons Restore Defaults for All Queues - Restores default settings for all queues on the selected interface. Submit - Send the updated configuration to the switch. Configuration changes take effect immediately.
Page 620: Ip Multicast Menu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Queue Management Type - Queue depth management technique used for queues on this interface. This is only used if device supports independent settings per-queue. Queue Management Type can only be one of the following: taildrop 10.2.6 IP Multicast Menu...
Page 621 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.1.2. Configuring DVMRP Interface Configuration Page Selection Criteria Unit/Slot/Port - Select the interface for which data is to be configured. You must configure at least one router interface before you configure a DVMRP interface. Otherwise you will see a message telling you that no router interfaces are available, and the configuration screen will not be displayed.
Page 622 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.1.3. Viewing DVMRP Configuration Summary Selection Criteria Unit/Slot/Port - Select the interface for which data is to be displayed. You must configure at least one router interface before you can display data for a DVMRP interface. Otherwise you will see a message telling you that no router interfaces are available, and the configuration summary screen will not be displayed.
Page 623 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Minor Version - The DVMRP Minor Version for the specified neighbor on the selected interface. Capabilities - The DVMRP capabilities of the specified neighbor on the selected interface. Received Routes - The number of routes received for the specified neighbor on the selected interface.
Page 624 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Next Hop Interface - The outgoing interface for this next hop. Type - The next hop type. 'Leaf' means that no downstream dependent neighbors exist on the outgoing interface. Otherwise, the type is 'branch'.
Page 625: Managing Igmp Protocol
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.1.6. Viewing DVMRP Route Summary Non-Configurable Data Source Address - The network address that is combined with the source mask to identify the sources for this entry. Source Mask - The subnet mask to be combined with the source address to identify the sources for this entry.
Page 626 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Submit - Send the updated configuration to the router. Configuration changes take effect immediately. These changes will not be retained across a power cycle unless a save is performed. 10.2.6.2.2. Configuring IGMP Interface Configuration Page...
Page 627 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Last Member Query Interval - Enter the last member query interval in tenths of a second. This the maximum response time to be inserted into group-specific queries sent in response to leave group messages, and is also the amount of time between group-specific query messages.
Page 628 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Protocol State - The operational state of IGMP on the selected interface. Version - The version of IGMP configured on the selected interface. Query Interval - The frequency at which IGMP host-query packets are transmitted on the selected interface.
Page 629 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Refresh - Refresh the data on the screen with the present state of the data in the router. 10.2.6.2.4. Viewing IGMP Cache Information Selection Criteria Unit/Slot/Port - Select the Slot and port for which data is to be displayed. Slot 0 is the base unit.
Page 630 Korenix Technology Co., Ltd. Layer 3 Stackable Switch timer. While this timer is non-zero, the local router ignores any IGMPv2 leave messages for this group that it receives on the selected interface. This field is displayed only if the interface is configured for IGMP version 1.
Page 631: Defining Multicast Configuration
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Source Filter Mode - The source filter mode (Include/Exclude/NA) for the specified group on this interface. Source Hosts - This parameter shows source addresses which are members of this multicast address. Expiry Time - This parameter shows expiry time interval against each source address which are members of this multicast group.
Page 632 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.3.2. Configuring Interface’s Multicast Configuration Page Selection Criteria Unit/Slot/Port - Select the routing interface you want to configure from the dropdown menu. Configurable Data TTL Threshold - Enter the TTL threshold below which a multicast data packet will not be forwarded from the selected interface.
Page 633 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Group IP to fully identify a single route whose Mroute table entry you want to display or clear. You may leave this field blank. Group IP - Enter the destination group IP address whose multicast route(s) you want to display or clear.
Page 634 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Source - Select Create Static Route to configure a new static entry in the MRoute table, or select one of the existing entries from the pulldown menu. Configurable Data Source IP - Enter the IP Address that identifies the multicast packet source for the entry you are creating.
Page 635 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.3.6. Configuring Multicast Admin Boundary Configuration Page The definition of an administratively scoped boundary is a mechanism is a way to stop the ingress and egress of multicast traffic for a given range of multicast addresses on a given routing interface.
Page 636: Configuring Multicast Mdebug
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.3.7. Viewing Multicast Admin Boundary Configuration Page Non-Configurable Data Unit/Slot/Port - The router interface to which the administratively scoped address range is applied. Group IP - The multicast group address for the start of the range of addresses to be excluded.
Page 637 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.4.2. Viewing Mrinfo Summary Page This screen displays the results of an mrinfo command. Non-Configurable Data Router Interface - The IP address of the router interface for which configuration information was requested.
Page 638 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 239.255.255.255. Command Buttons Submit - Initiate the mstat command on the router. If the mstat command completes successfully the browser will display the Mstat Show screen. If the mstat command fails, you will see the Mstat Run screen again.
Page 639 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.4.5. Defining Mtrace Admin Configuration Page Configurable Data Admin Mode - Select enable or disable from the pulldown menu. If you select enable the router will process and forward mtrace requests received from other routers, otherwise received mtrace requests will be discarded.
Page 640: Managing Pim-Dm Protocol
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.4.7. Viewing Mtrace Summary Page This screen displays the results of an mtrace command. The mtrace command is used to trace the path from source to a destination branch for a multicast distribution tree.
Page 641 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.5.1. Configuring PIM-DM Global Admin Configuration Page Configurable Data Admin Mode - Select enable or disable from the pulldown menu to set the administrative status of PIM-DM in the router. The default is disabled.
Page 642 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.5.3. Viewing Interface’s PIM-DM Configuration Page Selection Criteria Unit/Slot/Port - Select the physical interface for which data is to be displayed. There must be configured at least one router interface before displaying data for a PIM-DM interface, otherwise a message will be displayed.
Page 643: Managing Pim-Sm Protocol
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.6 Managing PIM-SM Protocol 10.2.6.6.1. Configuring PIM-SM Global Configuration Page Configurable Data Admin Mode - Select enable or disable from the pulldown menu to set the administrative status of PIM-SM in the router. You must enable IGMP before enabling PIM-SM. The default is disabled.
Page 644 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.6.3. Configuring Interface’s PIM-SM Configuration Page Selection Criteria Unit/Slot/Port - Select the slot and port for which data is to be displayed or configured. Slot 0 is the base unit. Configurable Data Mode - Select enable or disable from the pulldown menu to set the administrative status of PIM-SM in the router.
Page 645 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.6.4. Viewing Interface’s PIM-SM Configuration Page Selection Criteria Unit/Slot/Port - Select the slot and port for which data is to be displayed. Slot 0 is the base unit. Non-Configurable Data Mode - The administrative status of PIM-SM in the router: either enable or disable.
Page 646 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.6.5. Viewing PIM-SM Component Summary Page Non-Configurable Data Component Index - Unique number identifying the component index. Component BSR Address - Displays the IP address of the bootstrap router (BSR) for the local PIM region.
Page 647 Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.6.6. Viewing PIM-SM RP Summary Page Non-Configurable Data Group Address - Displays IP multicast group address. Group Mask - Displays Multicast group address mask. Address - Displays IP address of the Candidate-RP.
Page 648: Stacking Menu
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.6.6.8. Configuring PIM-SM Static RP Configuration Page Configurable Data IP Address - IP Address of the RP to be created or deleted. Group - Group Address of the RP to be created or deleted.
Page 649 Korenix Technology Co., Ltd. Layer 3 Stackable Switch become a management unit. This field is non-configurable for users with read-only access. Non-Configurable Data Role - Displays whether the selected switch is the master or a slave. MAC Address - The MAC address of switch units.
Page 650: Downloading Runtime Image To Stack Members
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.7.2 Downloading Runtime Image to Stack Members Selection Criteria Unit - Displays the list of all units of the stack other than the management unit. Command Buttons Submit - Copies the code from the management Unit to stack unit(s) specified by the unit selector.
Page 651: Viewing Stack Summary Information
Korenix Technology Co., Ltd. Layer 3 Stackable Switch 10.2.7.3 Viewing Stack Summary Information Non-Configurable Data Switch ID - Displays the ID of the unit. The maximum number of units allowed in the stack is 8. Role - This field indicates whether the unit is a Master or Slave.
Page 652: Viewing Stack Port Counters Information
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Non-Configurable Data Unit - Displays the unit. Interface - Displays the stackable interfaces on the given unit. Configured Stack Mode - Displays the configured mode for the given interface. Even though the configured mode is immediately saved in the NVRAM, on the unit on which the port is located, the run-time mode is not changed.
Page 653: Viewing Stack Port Counters Detail Information
Korenix Technology Co., Ltd. Layer 3 Stackable Switch Error Rate (Errors/s) - Displays an approximate error rate on the stack port. Total Errors - Displays the total number of errors since boot. The counter may wrap. Command Buttons Refresh - Refreshes the data on the page.
Page 654 Korenix Technology Co., Ltd. Layer 3 Stackable Switch Command Buttons Refresh - Refreshes the data on the page. _____________________________________________________________________________ Stackable Layer 3 Managed Ethernet Switch User Manual Page: 654/655...
Page 655 Revision History Version Description Date V1.0 The 1 release version. Jul. 31, 2009 V1.1 Add LLDP configuration. Aug. 5, 2009...

Korenix JetNet 6524G User Manual

1 Introduction

2 Installation and Quick Startup

3 Console and Telnet Administration Interface

4 Web-Based Management Interface

5 Command Line Interface Structure and Mode-Based CLI

6 Switching Commands

Quick Links

User Manual

Related Manuals for Korenix JetNet 6524G

Summary of Contents for Korenix JetNet 6524G