1. Manuals
  2. Brands
  3. Billion Manuals
  4. Network Router
  5. BIPAC 5102 Series
  6. User manual

Billion BIPAC 5102 Series User Manual

(802.11g) adsl modem/router
Hide thumbs Also See for BIPAC 5102 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
BIPAC 5102 Series
(802.11g) ADSL Modem/Router
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BIPAC 5102 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Billion BIPAC 5102 Series

Summary of Contents for Billion BIPAC 5102 Series

  • Page 1 BIPAC 5102 Series (802.11g) ADSL Modem/Router User’s Manual...

  • Page 2: Table Of Contents

    1.2 Features of the BIPAC 5102 Series ..............3 1.3 Applications for the BIPAC 5102 Series ............. 6 Chapter 2 ..........................7 2.1 Important note for using the BIPAC 5102 Series ADSL Router......7 2.2 Package Contents ....................7 2.3 The Front LEDs ....................8 2.4 The Rear Ports ....................

  • Page 3: Chapter 1

    Introduction the BIPAC 5102 Series 1.1 Introducing the BIPAC 5102 Series Welcome to the Billion BIPAC 5102 Series ADSL Router. Your Billion router is an “all-in-one” unit, combining an ADSL modem, ADSL router and Ethernet network switch, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection.
  • Page 4 to target a machine on your network. Secondly, it can block and redirect certain ports to limit the services that outside users can access. For example, to ensure that games and other Internet applications will run properly, user can open some specific ports for outside users to access internal services in network.

  • Page 5: Features Of The Bipac 5102 Series

    1.2 Features of the BIPAC 5102 Series ADSL Multi-Mode Standard supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It also supports rate management that allows ADSL subscribers to select an Internet access speed suiting their needs and budgets. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2;...
  • Page 6 (ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News, Net2phone, Ping, NetMeeting, IP phone and others. Firewall Supports simple firewall with NAT technology and provides option for blocking access from Internet, like Telnet, FTP, TFTP, WEB, SNMP and IGMP. Domain Name System (DNS) relay Provides an easy way to map the domain name (a friendly name for users such as www.yahoo.com) and IP address.
  • Page 7 client IP addresses and distribute them including IP address, subnet mask as well as DNS IP address to local computers. It provides an easy way to manage the local IP network. RIP1/2 Routing Supports RIP1/2 routing protocol for routing capability. Simple Network Management Protocol (SNMP) It is an easy way to remotely manage the router via SNMP.

  • Page 8: Applications For The Bipac 5102 Series

    1.3 Applications for the BIPAC 5102 Series...

  • Page 9: Chapter 2

    Installing the BIPAC 5102 Series 2.1 Important note for using the BIPAC 5102 Series ADSL Router Do not use the BIPAC 5102 Series in high humidity or high temperatures. Do not use the same power source for the BIPAC 5102 Series as other equipment.

  • Page 10: The Front Leds

    Quick Start Guide (105*150*mm) 2.3 The Front LEDs BIPAC 5102 BIPAC 5102S BIPAC 5102G Meaning PPP : Lit steady when there is a PPPoA / PPPoE connection. Lit when successfully connected to an ADSL DSLAM ADSL: (“linesync”). Lit when connected to an Ethernet device. LAN Port Green for 100Mbps;...

  • Page 11: The Rear Ports

    2.4 The Rear Ports BIPAC 5102 BIPAC 5102S BIPAC 5102G Port Meaning Connect the supplied power adapter to this jack. After the device is powered on, press it to reset the device or restore to factory default settings. RESET 0-3 seconds: reset the device 6 seconds above: restore to factory default settings (this is used when you can not login to the router, e.g.

  • Page 12: Cabling

    LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your Billion router (e.g. telephones, fax machines, analogue modems) have a line filter connected between them...

  • Page 13: Chapter 3

    If not, please refer to your Windows-related or other operating system manuals. Any TCP/IP capable workstation can be used to communicate with or through the BIPAC 5102 Series. To configure other types of workstations, please consult the manufacturer’s documentation.

  • Page 14: Configuring Pc In Windows Xp

    Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties.

  • Page 15: Configuring Pc In Windows 2000

    Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties.

  • Page 16: Configuring Pc In Windows 98/Me

    Configuring PC in Windows 98/Me 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2.Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3.Select the Obtain an IP address automatically radio button.
  • Page 17 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2.Select TCP/IP Protocol and click Properties. 3.Select the Obtain an IP address from a DHCP server radio button and click OK.

  • Page 18: Factory Default Settings

    3.2 Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site: PPPoE DHCP server: DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 100 3.2.1 Username and Password...

  • Page 19: Lan And Wan Port Addresses

    3.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 The PPPoE function is enabled to Subnet Mask 255.255.255.0 automatically get the WAN port DHCP server function...

  • Page 20: Configuring With Your Web Browser

    Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt will appear. The default username and password are “admin” and “admin”. Congratulation! You are now successfully logon to the BIPAC 5102 Series ADSL Router!

  • Page 21: Chapter 4

    Advanced Setup (Password, LAN, WAN, Wireless, NAT, Security, Dynamic DNS, Time Zone, Remote Management Control, UPnP) Static Route（Current Route） Maintenance (System Status, DHCP Table, Diagnostic, Firmware) Logout. Please see the relevant sections of this manual for detailed instructions on how to configure your Billion router.

  • Page 22: Wizard Setup

    4.1 Wizard Setup 4.1.1 Wizard Setup Use the Wizard Setup screens to configure your system for Internet access settings and fill in the fields with the information in the Internet Account Information table of the Compact Guide or Read Me First. Your ISP may have already configured some of the fields in the wizard screens for you.

  • Page 23: Pppoe

    4.1.2 PPPoE PPPoE （PPP over Ethernet）provides access control and billing functionality in a manner similar to dial-up services using PPP. Select PPPoE from the Encapsulation in the first wizard screen to display the screen as shown. Service Name: Type the name of your PPPoE service here User Name: Enter the user name exactly as your ISP assigned.
  • Page 24 time and specify an idle time-out (in seconds) in the Max. Idle Timeout field Network Address Translation: Select None, Many to One or Many to Many from the drop-sown list box. Refer to the NAT chapter for more details.

  • Page 25: 1483 Routed Ip

    4.1.3 1483 Routed IP Select 1483 Router IP from the Encapsulation drop-down list box in the first wizard screen to display the screen as shown. IP Address: Type your ISP assigned IP address in the IP Address text box below. Network Address Translation: Select None, Many to One or Many to Many from the drop-sown list box.

  • Page 26: 1483 Bridged Ip

    4.1.4 1483 Bridged IP Select 1483 Bridged IP from the Encapsulation in the wizard screen to display the screen as shown. IP Address: Type your ISP assigned IP address in the IP Address text box below. Subnet Mask: Enter a subnet mask in dotted decimal notation. Gateway: You must specify a gateway IP address (supplied by your ISP) when you use 1483 Bridged IP in the Encapsulation field in the previous screen.

  • Page 27: Pppoa

    4.1.5 PPPoA PPPoA stands for Point to Point Protocol over ATM Adaptation Layer 5 (AAL5). It provides access control and billing functionality in a manner similar to dial-up services using PPP. Select PPPoA from the Encapsulation in the first wizard screen to display the screen as shown.

  • Page 28: Wizard Setup Configuration

    Verify the settings in the screen shown next. To change the LAN information on the BIPAC 5102 Series, click Change LAN Configurations. If you want to change your BIPAC 5102 Series LAN settings, click Change LAN Configuration to display the screen as shown next.
  • Page 29 LAN IP Address: Enter the IP address of BIPAC 5102 in dotted decimal notation, for example, 192.168.1.254 (factory default). LAN Subnet Mask Enter a subnet mask in dotted decimal notation. DHCP Server: From the DHCP Server drop-down list box, select On to allow ADSL Router to assign IP addresses, an IP default gateway and DNS servers to computer systems that support the DHCP client.

  • Page 30: Wizard Setup Configuration

    4.1.7 Wizard Setup Configuration The BIPAC 5102 Series automatically tests the connection to the computer(s) connected to the LAN ports. To test the connection from the ADSL Router to the ISP, click Start Diagnose. Otherwise click Return to Main Menu to go back to the Site Map screen.

  • Page 31: Advanced Setup

    4.2 Advanced setup 4.2.1 Password In factory setting, the default password is admin, and that for user is also password. You can change the default password to ensure that someone cannot adjust your settings without your permission. Every time you change your password, please record the password and keep it at a safe place.

  • Page 32: Lan

    If set to None, the DHCP server will be disabled. If set to Relay, the BIPAC 5102 Series acts as a surrogate DHCP server and relays DHCP requests and responses between the remote server and the clients. Enter the IP address of the actual, remote DHCP server in the Remote DHCP Server field in this case.
  • Page 33 address of the actual remote DHCP server here. TCP/IP IP Address: Enter the IP address of ADSL Router in dotted decimal notation, for example, 192.168.1.254 (factory default). IP Subnet Mask: The default is 255.0.0.0. User can change it to other such as 255.255.255.0.Type the subnet mask assigned to you by your ISP (if given).

  • Page 34: Wan Setup

    4.2.3 WAN Setup A WAN (Wide Area Network) is an outside connection to another network or the Internet. And allows the user to set the configuration for the WAN/ADSL ports. To change BIPAC 5102 Series WAN remote node settings, click WAN.
  • Page 35 4.2.3.1 Half Bridge Name: Enter the name of your Internet Service Provider Mode: Select Routing (default) or Bridge Encapsulation: select Bridge in the Mode field, select either PPPoA or RFC 1483. select Routing in the Mode field, select PPPoA, RFC 1483, ENET ENCAP or PPPoE. Multiplex: Select the method of multiplexing used by your ISP.
  • Page 36 Cell Rate: Cell rate configuration often helps eliminate traffic congestion that slows transmission of real time data such as audio and video connections. Peak Cell Rate: Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak Cell Rate (PCR).

  • Page 37: Wireless

    4.2.4 Wireless 802.11g is only supported for the BIPAC 5102G This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as simple as two computers with wireless LAN cards communicating in a peer-to-peer network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN.
  • Page 38 4.2.4.1 Wireless LAN-Wireless ESSID: Enter the unique ID given to the Access Point (AP), which is already built-in to the router’s wireless interface. To connect to this device, your wireless clients must have the same ESSID as the device. Hide ESSID: Select Yes to hide the ESSID in so a station cannot obtain the ESSID through passive scanning.

  • Page 39: Mac Filter

    the router. There are four keys for your selection. The input format is in HEX style, 5 and 13 HEX codes are required for 64-bitWEP and 128-bitWEP respectively. If you chose 64-bit WEP, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "A-F").
  • Page 40 Active: Select Yes from the drop down list box to enable MAC address filtering. Action: Define the filter action for the list of MAC addresses in the MAC address filter table. Select Deny Association to block access to the router, MAC addresses not listed will be allowed to access the router.

  • Page 41: Nat

    4.2.5 NAT The NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. The default setting is Dynamic NAPT. It provides dynamic Network Address Translation capability between LAN and multiple WAN connections, and the LAN traffic is routed to appropriate WAN connections based on the destination IP addresses and Route Table.

  • Page 42: Configuring Address Mapping

    End Port No.: Enter a port number in this field. IP Address: Enter your server IP address in this field. 4.2.5.3 Configuring Address Mapping To change your BIPAC 5102 Series address mapping settings, click NAT, Select Many to Many and click Edit Details to open the following screen.
  • Page 43 Local Start IP: This is the starting Inside Local IP Address. Local IP addresses are N/A for Server port mapping. Local End IP: This is the end Inside Local IP Address (ILA). If your rule is for all local IP addresses, then enter 0.0.0.0 as the Local Start IP address and 255.255.255.255 as the Local End IP address.

  • Page 44: Editing An Address Mapping Rule

    4.2.5.4 Editing an Address Mapping Rule To edit an address mapping rule, click the rule’s link in the NAT Address Mapping Rules screen to display the screen shown next. Type: 1-1: One-to-one mode maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type.

  • Page 45: Security

    4.2.6 Security Inbound direction of Packet Filter rules to prevent unauthorized computers or applications accessing your local network from the Internet. You can choose all filter rules by yourself, and the security is offer to some sections: Telnet, FTP, TFTP, Web, SNMP and Ping.

  • Page 46: Dynamic Dns

    Active: Select this check box to use dynamic DNS. Service Provider: Select the name of your Dynamic DNS service provider. Host Name: Type the domain name assigned to your BIPAC 5102 Series by your Dynamic DNS provider. E-mail Address: Type your e-mail address.

  • Page 47: Time Zone

    4.2.8 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network. Choose your local time zone. After a successful connection to the Internet, the router will retrieve the correct local time from the SNTP server you have specified.
  • Page 48 (that you configured above) to set its internal system clock. Please wait for up to 60 seconds while the BIPAC 5102 Series locates the time server. If the BIPAC 5102 Series cannot find the time server, please check the time server protocol and its IP address.

  • Page 49: Remote Management

    Secured Client IP: The default 0.0.0.0 allows any client to use this service to remotely manage the BIPAC 5102 Series. Type an IP address to restrict access to a client with a matching IP address.

  • Page 50: Upnp

    Allow users to make configuration changes through UPnP: Select this check box to allow UPnP-enabled applications to automatically configure the BIPAC 5102 Series so that they can communicate through the BIPAC 5102 Series, for example by using NAT traversal, UPnP applications automatically reserve a NAT forwarding port in order to communicate with another UPnP enabled device;...
  • Page 51 Step 3. In the Communications window, select the Universal Plug and Play check box in the Components selection box. Step 4. Click OK to go back to the Add/Remove Programs Properties window and click Next. Step 5. Restart the computer when prompted. Follow the steps below to install the UPnP in Windows XP.
  • Page 52 The Windows Optional Networking Components Wizard window displays. Step 4. Select Networking Service in the Components selection box and click Details. Step 5. In the Networking Services window, select the Universal Plug and Play check box. Step 6. Click OK to go back to the Windows Optional Networking Component Wizard window and click Next.
  • Page 53 Auto-discover Your UPnP-enabled Network Device Step 1. Click start and Control Panel. Double-click Network Connections. An icon displays under Internet Gateway. Step 2. Right-click the icon and select Properties. Step 3. In the Internet Connection Properties window, click Settings to see the port mappings there were automatically created.

  • Page 54: Web Configurator Easy Access

    With UPnP, you can access the web-based configurator on the BIPAC 5102 Series without finding out the IP address of the BIPAC 5102 Series first. This comes helpful if you do not know the IP address of the BIPAC 5102 Series.
  • Page 55 Step 4. An icon with the description for each UPnP-enabled device displays under Local Network. Step 5. Right-click on the icon for your BIPAC 5102 Series and select Invoke. The web configurator login screen displays. Step 6. Right-click on the icon for your BIPAC 5102 Series and select Properties. A...

  • Page 56: Static Route

    4.3 Static Route 4.3.1 Current Route If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet. Active: Whether the connection is currently active. Name: Enter the name of your Internet Service Provider Destination IP：This is the destination subnet IP address.

  • Page 57: Maintenance

    4.4 Maintenance Use the maintenance screens to view system information, upload new firmware, manage configuration and restart your BIPAC 5102 Series 4.4.1 System Status System Status: System Name: This is the name of the router. It is for identification purposes.
  • Page 58 WAN Information: IP Address: This is the WAN port IP address IP Subnet Mask: This is the WAN port IP subnet mask. Default Gateway: This is the IP address of the default gateway VPI/VCI: This is the Virtual Path Identifier and Virtual Channel Identifier that you entered in the first Wizard screen.

  • Page 59: System Statistics

    4.4.2 System Statistics Read-only information here includes port status and packet specific statistics. Also provided are "system up time" and "poll interval(s)". System up Time:This is the elapsed time the system has been up CPU Load: This field specifies the percentage of CPU utilization. WAN Port Statistics: This is the WAN port.
  • Page 60 Status: For the WAN port, this displays the port speed and duplex setting if you're using Ethernet encapsulation and down (line is down), idle (line (ppp) idle), dial (starting to trigger a call) and drop (dropping a call) if you're using PPPoE encapsulation.For a LAN port, this shows the port speed and duplex setting.

  • Page 61: Dhcp Table

    4.4.3 DHCP Table DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a server. Host Name: This is the name of the host computer. IP Address: This field displays the IP address relative to the Host Name field MAC Address: This field displays the MAC (Media Access Control) address of the computer with the displayed host name.

  • Page 62: Wireless

    4.4.4 Wireless 802.11g is only supported for the BIPAC 5102G These read-only screens display information about the router’s wireless LAN. 4.4.4.1 Association List This screen displays the MAC address(es) of the wireless clients that are currently logged in to the network. Click Wireless LAN and then Association List to open the screen shown next.
  • Page 63 Channel: This is the index number of the channel. Activity: This field displays Yes if another AP or Ad-hoc network is using the channel within the router’s transmission range.

  • Page 64: Diagnostic

    TCP/IP Address: Type the IP address of a computer that you want to ping in order to test a connection. Ping: Click this button to ping the IP address that you entered. Reset System: Click this button to reboot the BIPAC 5102 Series. A warning dialog box...

  • Page 65: Diagnostic Dsl Line

    is then displayed asking you if you're sure you want to reboot the system. Click OK to proceed. 4.4.5.2 Diagnostic DSL Line Reset ADSL Line: Click this button to reinitialize the ADSL line. The large text box above then displays the progress and results of this operation ATM Status: Click this button to view ATM status.

  • Page 66: Firmware

    To upgrade the firmware of BIPAC 5102 Series, you should download or copy the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file.
  • Page 67 DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router. Warning...

  • Page 68: Restart

    4.4.7 Restart Click Restart with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings.

  • Page 69: Logout

    4.5 Logout To exit the router’s web interface, choose Logout. Please ensure that you have saved the configuration settings before you logout. Be aware that the router is restricted to only one PC accessing the configuration web pages at a time. Once a PC has logged into the web interface, other PCs cannot get access until the current PC has logged out of the web interface.

  • Page 70: Chapter 5

    Chapter 5 Troubleshooting If the ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems starting up the router Problem Corrective Action...

  • Page 71: Problems With The Lan Interface

    Frequent loss of Ensure that all other devices connected to the same ADSL linesync telephone line as your router (e.g. telephones, fax machines, (disconnections). analogue modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and ensure that all line filters are correctly installed and the right way around.

  • Page 72: Appendix

    Most problems can be solved by referring to the Troubleshooting section in the User’s Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billion AUSTRALIA http://www.billion.com.au ©2005 Billion Electric Co., Ltd. PC Range P/L. All Rights Reserved. WORLDWIDE http://www.billion.com...

Table of Contents