Canon VB101 User Manual page 48

Log Messages
A016 Amount of transmitted video data (info)
%1@%2 %3 frames/%4 bytes in %5 seconds
Message
Client type (LS/D|LS/H|VW/D)
%1
Client host IP address
%2
%3 Number of frames
Number of bytes
%4
Video transmission time
%5
Explanation This shows the results of video transmission for a video transmission client.
A021 Data transmission error count for VIEW-Windows video transmission clients (notice)
VW/D@%1 %2 transmission errors
Message
Client host IP address
%1
Transmission error count
%2
Explanation This shows the number of video transmission errors that have occurred during monitoring station operation.
Response Compare this with the A016 frame count just shown.
If the error count is relatively high, the system is overloaded.
Lower the maximum frame rate setting or set a lower traffic control setting on the monitoring station.
A022 Applet archive load failure (warning)
archive/%1 not found
Message
%1 Applet archive name (glimpse.cab|glimpse.zip|lvapplet.cab|lvapplet.zip|imagemap.
gif|snapanim.cab|snapanim.zip|digits.gif)
Explanation The applet archive file does not exist or is corrupted.
Response Copy the missing (or damaged) file in the "/archive" applet from the CD-ROM and reboot.
The original applet archive file is in the CD-ROM.
A023 Status change of external input devices (err)
a %1 detected at %2
Message
external device input change (front-edge | rear-edge | pulse | notch)
%1
%2 external device terminal (In1 | In2)
Explanation A change was detected at external device terminal In1 or In2. "front edge" denotes OFF
"rear-edge" denotes "ON
and notch denotes ON
ON and OFF periods detected during OFF and ON states respectively.
A024 Picture recording suspended and restarted (notice)
picture recording %1
Message
suspended | recovered
%1
Explanation Picture recording stopped because of error or picture recording restarted because of error recovery.
Error details will be output as A025.
94
OFF, "pulse" denotes OFF ON OFF,
OFF ON. "pulse" and "notch" are brief (10-20 milliseconds)
A025 Picture recording processing error (warning)
Message
%1
Explanation
Response
A026 Picture recording processing failure count (warning)
Message
%1
Explanation
Response
A028 Recorded picture deletion completed successfully (info)
Message
%1
Explanation
A029 Recorded picture deletion ended abnormally (warning)
Message
%1
Explanation
Response
A031 Picture index restoration completed successfully (info)
Message
ON,
Explanation
A032 Picture index restoration ended abnormally (warning)
Message
%1
Explanation
Response
picture recording failed: %1
busy|index broken|index full|no video data|no storage device|I/O error
This shows the details of an error during picture recording. This message is only displayed when
errors of different types occur. (This message is not displayed if the same error occurs repeatedly.)
If the problem is "busy", no response is required. For "index broken" (corrupted index file), repair
the index. For "index full" (number of pictures that can be recorded has been exceeded), delete
some of the recorded pictures. For "no video data" (video signal input error or maximum picture
size exceeded), check the camera and camera settings. For "no storage device" (memory card
not inserted), insert a memory card. For "I/O error" (input-output error), check the memory card.
picture recording failed %1 times
Number of pictures that could not be recorded
This shows the number of times picture recording failed in the period between "suspended" and "recovered" in message A024.
In addition to the responses to A025, take steps such as reducing the picture recording frequency specified in the schedule.
%1 pictures are deleted
Number of recorded pictures deleted
Recorded picture delete processing was completed successfully.
picture deletion failed: %1
index broken|no storage device|I/O error
Processing was cancelled because an error was detected during recorded picture deletion.
For "index broken" (corrupted index file), repair the index (Rebuilding of recorded picture list).
For "no storage device" (memory card not inserted), insert a memory card.
For "I/O error" (input-output error), check the memory card.
index restoration completed
Picture index restoration processing was completed successfully.
index restoration failed: %1
no space left|no storage device|I/O error
Processing was cancelled because an error was detected during picture index restoration.
For "no space left" (memory card full), delete some files or replace the memory card.
For "no storage device" (memory card not inserted), insert a memory card.
For "I/O error" (input-output error), check the memory card.
Log Messages
6
95