Canon VB101 User Manual page 51

Log Messages
S015 Root directory entry count error (err)
root directory doesn't span an integral number of sector sizes
Message
Explanation The number of root directory entries is not consistent with the recording area size
for root directory entries.
The file system may be corrupted or it may not be formatted as a FAT file system.
If this error affects the internal file system, contact an authorized Canon service representative. If it affects a memory card, replace the memory card.
Response
S016 Logical sector size error (err)
logical sector size is not a multiple of the physical sector size
Message
Explanation The logical sector size is not a multiple of the physical sector size.
The file system may be corrupted or it may not be formatted as a FAT file system.
Response If this error affects the internal file system, contact an authorized Canon service representative. If it affects a memory card, replace the memory card.
S017 Boot sector error (err)
Invalid disk format in boot sector
Message
A value recorded in the boot sector is not valid for the FAT format.
Explanation
The file system may be corrupted or it may not be formatted as a FAT file system.
If this error affects the internal file system, contact an authorized Canon service representative. If it affects a memory card, replace the memory card.
Response
S018 Write error during file system checking (err)
chkdsk:Disk Write Error
Message
Explanation A write error occurred during file system checking.
Response If this error affects the internal file system, contact an authorized Canon service representative. If it affects a memory card, replace the memory card.
S019 Read error during file system checking (err)
chkdsk: Disk Read Error
Message
Explanation A read error occurred during the file system check.
Response If the error is related to the built-in file system, contact your local Canon service agent. If the error is related to the memory card, replace the memory card.
S020 File system checking ended abnormally (err)
device name (%1) chkdsk unsuccessful
Message
Device name (/dev/hd0a|ata card)
%1
Explanation This error message appears after error messages S010 to S019. If the device name is "ata card",
the error is on the memory card. If the device name is "/dev/hd0a", it affects the internal file system.
Response If this error affects the internal file system, contact an authorized Canon service representative. If it affects a memory card, replace the memory card.
S021 File system structural defect (err)
disk has a structural default
Message
Explanation Due to a file system structural defect, file system check and mount is not possible.
Response If the error is related to the built-in file system, contact your local Canon service agent. If the error is related to the memory card, replace the memory card.
100
S023 The erase count for the on-board flash ROM exceeded the limit (err)
FlashROM erase count(%1)exceeded the limit
Message
%1 Erase count for the on-board flash ROM
Explanation The erase count limit for the on-board flash ROM has been exceeded.
Response Contact an authorized Canon service representative.
If you continue to write data after this error occurs, there is a risk of data corruption.
Remote firmware upgrade-related log messages
I001 Remote firmware upgrade write error (err)
cannot reboot as the firmware is broken
Message
Explanation Reboot cannot take place because there is an error in the firmware that was written onto read-only memory during
the firmware remote upgrade. This error is not a transfer error and has not occurred as a result of a break in transfer.
This type of error occurs only when firmware is erased from the ROM or when firmware is written onto the ROM.
Response Contact your local Canon service representative. There is a possibility that the flash ROM chip has been damaged.
I002 Application program is stopped because of the remote firmware upgrade (info)
application is halted for updating the firmware
Message
Explanation The application program has been stopped so that the firmware can be installed remotely. All operations
that are underway will be discontinued, and new commands for WebView, VIEW-Windows, image
recording and external device output control will not be accepted until a reboot has been carried out.
I003 Remote firmware upgrade completed (info)
Message firmware is updated
Explanation The remote firmware upgrade process has been completed.
I004 Remote firmware upgrade time-out (warnning)
reboot as the firmware update time is out
Message
Explanation A reboot has been carried out because the remote firmware upgrade process
performed a time-out.
Response Check the VB101 has restarted with the firmware installed before intialing remote upgrade process
(check the Version and Revision numbers that are displayed at the top of the Settings title page).
6
101