Inserting And Replacing Backup Lithium Batteries; Power Supply; Ac Operation; Battery Pack Operation - JVC GY-DV700W Instructions Manual

3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS

3-7 Inserting and Replacing Backup Lithium Batteries

The GY-DV700W uses a lithium battery for backup of the time code data and time date data. Install the provided lithium battery
before actually using the unit.
● Lithium battery: CR2032
"Li" indicator
OPERATE/WARNING
LIGHT
CH 1
RESET OVER AUTO OFF DEW ON
40 30 20 10 0 dB
CH 2 OVER SERVO RF L i OFF
32k 48k SLAVE PB NDF HOLD
MONITOR AUD LOCK SP
FILTER SELECT MENU WIDE COUNTER
H M S F
1 3200k REMAIN E BATT F CTL
ALARM REV FWD
2 5600k+1/8ND TC
H M UB
3 5600k
4 5600k+1/64ND
SHUTTER STATUS MONITOR
MENU
CH-1 AUDIO CH-2
LEVEL
AUTO IRIS FULL AUTO BLACK LOLUX
BACK L STRETCH
NORMAL NORMAL
SPOT L COMPRESS
NG POWER
ON OFF
Power switch
When the lithium battery is not in place or the battery is exhausted and requires a replacement, the "Li" indicator in the LCD display
will light up.
Replace lithium batteries with the POWER switch set to ON. Doing it with the POWER switch set to OFF will cause the loss of
backup data.
How to Install the Lithium Battery
Lithium battery cover
LITHIUM BATT.
1.
Push the lithium battery cover in the direction of the arrow
as illustrated and remove the cover.
2.
Slide the battery into place with its marked surface facing
upward.
3.
Return the lithium battery cover to its original position in the
unit.
E-34
CAUTION:
If the unit is not used for a lengthy period of time (one
month or more), remove the lithium battery. If the voltage
of the lithium battery becomes low, the set may malfunction.
CH-1 AUDIO CH-2
TC GENERATOR
LEVEL CH-1 CH-2
AUTO PRESET FREE
MANUAL REGEN REC
AUDIO SELECT
AUDIO INPUT
CH-1 CH-2 CONTINUE MENU
FRONT
REAR
LITHIUM BATT.
GROUP ITEM SELECT DATA SET
HOLD SHIFT ADVANCE PRESET
Lithium battery case
How to Remove Lithium Batteries
The lithium battery is easily
removed if you press at the edge
of the lithium battery at the place
indicated in the illustration on the
left and then pull the battery out.

4. POWER SUPPLY

The GY-DV700W is operable with AC power supply or battery pack.

4-1 AC Operation

Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply.
DC cable CH-1 AUDIO IN CH-2
EARPHONE DV LINE MIC LINE MIC TALLY
+48V ON ON +48V
DC INPUT
DC OUTPUT
AC power adapter
Precautions for Connection with the AC POWER
ADAPTER(AA-P250)
Always use the DC cable equipped with a ferrite core and
supplied with the AA-P250.
The DC cable VC-710(5m) can not be used.
If the cable is not equipped with a ferrite core, please contact
your JVC dealer.

4-2 Battery Pack Operation

The GY-DV700W can be operated with the following battery packs.
Flat shape type battery pack
Anton-Bauer battery pack

● Propack 13/14 Series

● Trimpack 13/14 Series

● Magnum 13/14 Series


● Compack 13/14 Series
● When the DC cable is connected to the DC INPUT connector, the power supply from the battery pack is interrupted and the
power starts to be supplied through the DC INPUT connector.
● Do not connect or disconnect the DC cable while operating with a battery pack.
The following symptoms may occur if the DC cable is connected or disconnected while operating with a battery pack.
• The power is cut off for a moment when the DC cable is disconnected.
• Noise to the video and audio signals occurs. Audio signal are muted.
● When operation is continued with DC input after the battery pack capacity has been used up, set the POWER switch to OFF
after the DC power is applied. Then switch ON again.
● If the GY-DV700W is left with the battery pack attached, a small amount of power is consumed even if the POWER switch on
the GY-DV700W is set to OFF. Remove the battery pack when the GY-DV700W is not going to be used.
Do not use any power source with large fluctuations in the
power source voltage, or power sources generating noise,
such as ripples.
1.
After making sure that the power switches of the GY-DV700W
and of the AA-P250 are set to OFF, connect the DC cable
from the AA-P250 to the DC INPUT connector of the GY-
DV700W as shown in the illustration.
2.
When the AA-P250 is used, set the CHARGE/CAMERA
switch to CAMERA.
3.
Press the POWER switch of the GY-DV700W to ON. Power
is supplied to the VCR section and the camera.
* For details, read the instruction manual of the AA-P250.
Note:
Do not remove or connect the DC cable while recording is
being performed.
* An Anton-Bauer battery pack cannot be connected
directly to the GY-DV700W. It is necessary to mount
the optional battery holder.
Battery holder: Anton-Bauer QRQ27
For details on how to mount the battery holder, see
page 37.
E-35