Basic System Connections And Adjustments; Basic System; Attaching The Zoom Lens (Optional); Attaching The Viewfinder - JVC GY-DV700W Instructions Manual

3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS

3-1 Basic System

For information on connection with the individual attachments, refer to the page explaining the respective connection methods.
MONITOR
MICROPHONE
MV-P615
3P
SHOULDER BELT
MIC HOLDER
KA-A50
1.5" VIEW FINDER
VF-P116W
DV CAMCORDER
MICROPHONE
OPERATE/WARNING
RESET
MONITOR SELECT
1 3200k FILTER ALARM
2 5600k+1/8ND
3 5600k
4 5600k+1/64ND
SHUTTER STATUS MONITOR
MENU
CH-1 AUDIO CH-2
LEVEL
AUTO IRIS FULL AUTO BLACK LOLUX
NORMAL BACK L NORMAL STRETCH
SPOT L COMPRESS
C
NG POWER
ON OFF
ZOOM LENS
A19 x 8.7BW (FUJINON)
TRIPOD BASE
A19 x 8.7B12 (FUJINON)
YJ18 x 9BK12 (CANON)
GY-DV700W
STANDARD PACKAGE
FOCUS MANUAL UNIT
HZ-FM13 (FUJINON)
HZ-FM15 (CANON)
TRIPOD
TP-P300
ZOOM SERVO UNIT
CARRYING CASE
HZ-ZS13B
DOLLY
TP-P205
When 4:3 lens is mounted on the GY-DV700W.
1 When used in the 4:3 mode, approximately 20% of the image angle is shifted to the telephoto-side.
2 To use the 16:9 mode, change the setting by means of the ASPECT RATIO item in the GY-DV700W's camera OPERATION
MENU.
E-30
WIRELESS RECEIVER (WEK)
BATTERY
WRR-810(SONY)
NP-1B TYPE
EARPHONE BATTERY CHARGER
BATTERY
NP-1B TYPE
BATTERY HOLDER
COVER (WEK)
NB-G1 (4PACK) BATTERY CHARGER
BH-P27
(AC POWER ADAPTER)
BATTERY
AA-G10(B)
NB-G1
LIGHT
ON OFF
COUNTER
CTL
TC UB
4P 4P
AC
VIDEO LIGHT
AC POWER ADAPTER
(NB-G1 BATTERY CHARGER)
(ANTON BAUER. PROTEC)
AA-P250
ANTON BAUER
ANTON BAUER ANTON BAUER BATTERY
BATTERY CHARGER
BATTERY HOLDER
(PRO PAC, MAGNUM,
(QRQ27)
TRIMPAC, HYTRON)
IEEE1394 CABLE
RS232C CABLE
VC-P893 (For PC/AT)
Y/C CABLE
VCG30, VCG50
BNC CABLE
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS

3-2 Attaching the Zoom Lens (optional)

4.
1.
3
2.
Pin
Hole
Mounting
When unplugging the cable connector, first remove the lens
itself. Then grasp this portion and pull straight out.
3-3 Attaching the Viewfinder (optional)
1.
Mounting guide
5.
4.
Sliding
securing ring
Stopper
screw
2.
Viewfinder
mount
base
3.
Connector
1.
Loosen the mount ring.
2.
Connect the cable connector.
3.
Attach the lens with its pin aligned with the hole in the mount.
4.
Tighten the mount ring.
CAUTION:
Be sure to tighten the mount ring completely. Incomplete
tightening may result in the lens dropping off or disturbed
back focus.
1.
Loosen the stopper screw.
2.
Attach the viewfinder with its guide aligned with the shoe.
3.
Connect the cable
connector as shown in
the figure on the right.
VF
3
4.
Tighten the stopper screw.
5.
Tighten the ring.
E-31