Care For Using Cd's - Planet Audio P385UA User Manual

CARE FOR USING CD'S:

About CD-R/CD-R/W discs:
In addition to commercially-recorded audio CD's, this unit can play CD-R and
CD-R/W discs. In come cases, particularly when recorded on older CD burners,
some CD-R and CD-R/W discs may not play. Also, whenever you are recording
a CD for playback in this receiver, it is recommended that you record at 24x or
slower speed for CD-R and 4x or slower for CD-R/W to achieve higher signal
quality and better playback performance.
1. To keep the disc clean:
Do not attach any sticker or adhesive tape on the disc.
Handle the disc by its edge to keep the disc clean and do not touch the surface.
Before playing a disc, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc outwards from the disc center.
2. When one has already been inserted. Doing so may damage the unit
with labeled surface up, or it will damage the unit.
3. Do not expose the disc to direct sunlight or nearby heat sources such as heating
vents, caliduct which can cause the disc to warp.
Do not leave disc in a car if it is parked in direct sunlight as that will lead to a
considerable rise in the temperature inside the car.
4. Do not use any secondhand or rented disc, usually, there is glue on the surface of
those discs, it will stop the unit working and damage it.
5. Always store the disc in its case for protection. Scratched up discs will produce poor
sound performance and cause CD player to skip.
6. In raining day or wet area, the moisture may form on the disc or the optical parts,
the playback may not be possible. If moisture forms on the disc, wipe it off with a
soft cloth.
If moisture forms on the optical parts of the unit, allow the unit to sit for about one
hour with power on.
7. Do not use solvents such as benzine or thinners. Commercially available cleaners
or anti-static spray will damage the unit.
PDF created with FinePrint pdfFactory trial version
. Insert a disc
Page 11
http://www.pdffactory.com
7. BAND BUTTON
During radio mode, press the BND button briefly to select the radio broadcasting
band you would like to hear. The AM/FM band is toggled cyclically through the
tuning bands: ->FM 1-> FM 2 -> FM 3 -> AM 1->AM2 ->.
8. MODE BUTTON
Press the MODE button to change among tuner (radio), disc (when a disc is
loaded), SD/MMC card (when an SD/MMC card is inserted) , USB (when an
USB Flash Drive is inserted) and AUX mode.
9. MUTE BUTTON
This button serves to switch the MUTED state on/off.
Press the MUTE button to suppress the loudspeaker temporarily, and press
again to resume listening. The muted state will be also released when the
MODE, SEL button is pressed and VOL knob on the front panel is used.
10. INFRARED REMOTE CONTROL SENSOR
11. APS BUTTON (Auto-storage /Preset scan)
During radio mode:
1) when long pressing for more than 1 seconds, the radio searches from the
current frequency and checks the signal strength level until 6 station are
found. And then the 6 stations frequency are preset to the corresponding
preset memory numbered bank. The auto-storage operation is implemented
in the each selected band. When the auto-storage operation is finished, the
radio execute the Preset Scan.
2) when short pressing, the radio searches for each preset station in the current
band and holds at that preset number for 5 seconds with releasing mute, and
then search again.
In disc mode, MMC/SD or USB mode, press APS button repeatedly toselect
TRACK SEARCH, DIRECTORY SEARCH orFIRST CHARACTER SEARCH
mode.
In TRACK SEARCH mode, the LCD will display TRK T 000 and flash the
biggest digit0 that the MMC/SD card, USB or MP3 disc contain. Rotate the knob
to select the number of the flashing digit from 0 ~ 9. Then press SEL button to
confirm the number and flash next smaller digit 0.With the same means, select
the number of the flashing digit. After finishing selecting the number of all
flashing digit, press SEL button to play the track of the selected serial number.
In DIRECTORY SEARCH mode, the LCD will display the root folder(if there is
not the root folder, it will find a root folder named ROOT). Then rotate the knob
to select your desired folder, Finally press SEL button to play the first track of
the folder.
In FIRST CHARACTER SEARCH mode, the LCD will display A- rotate the knob
to select file's first character by the order of A~Z and 0~9. Then press >>| or |<<
button to select one file its first characters is the selected one. Finally press SEL
button to play the selected file.
Page 4