6.5 Teletext function 6.6 Subtitles function A.1 TRoUblEShooTIng A.2 SPECIfICATIonS STRong declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EEC and 73/23EEC; RohS 2002/95EEC * €0,14/Min. from German wired line * €0.42/Min. max. from mobile network Subject to alterations.
PART 1 • English 1.0 InTRoDUCTIon 1.1 Safety Instructions Do noT InSTAll YoUR RECEIvER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. Do noT EXPoSE ThE RECEIvER oR ITS ACCESSoRIES: To direct sunlight or near any other equipment that generates heat;...
It is advised not to store important information on USB storage devices used with the receiver. Always make backups of data on USB storage device before usage with receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information.
PART 1 • English 2.2 Remote Control Unit Fig. 3 Turns the receiver On/Stand-by. Mutes audio output of the receiver. Changes channel and controls numeric functions Toggles between TV and receiver (AV) mode Tv/R Toggles between TV or radio mode MEnU Shows the main menu and exits from any level of menu to view mode EXIT...
PART 1 • English 4.0 STARTIng UP Ensure your satellite signal is of good quality. It is recommended that you perform the first time installation following the Installation Wizard step by step. It will help you to easily achieve system configuration and channel installation.
PART 1 • English or South. Choose field Goto Position and press oK. Your dish will be turned to the position of satellite. Then choose NEXT and press oK. The Channel Setup menu will appear. Choose NEXT and press oK to start the scan. When the scan is completed, the receiver will save the services information automatically and exit to the normal play state.
PART 1 • English Press RED button, a satellite list will appear. Press tu to select the Add satellite satellite. If the satellite is not in the list, select “NEW SAT1”. After selection of a satellite, the Configure Antenna menu will appear. Please set the LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode.
PART 1 • English 5.3.1 Preference 5.3.1.1 language Setting You can change the language of the OSD, preferred audio and subtitles. Use pq to select the OSD language, Audio language or Subtitles language. Press oK or u to enter the language list and press pq to select the language. Press oK to confirm. 5.3.1.2 Tv settings You can set the TV mode, Screen mode and Video output settings..
Select this option in order to update your receiver with the latest software version. Software update service is available from satellite ASTRA 19.2E. note: If needed, parameters can be changed. Please ask your local STRONG dealer in case software update was not successful.
PART 1 • English e) File “Idapp1.ssu” will be created on USB device if “Loader + App” has been selected resp. file “userdb.ssu” if “User Database” has been selected. To restore user data a) Connect USB device with backup of database to USB port of receiver. b) Go to System Setting –...
PART 1 • English 6.0 WATChIng Tv AnD lISTEnIng To ThE RADIo 6.1 Program Information In normal operation status (no menu operation), press Info. The program information banner will be displayed showing channel number, channel name, current, next program name (if available from broadcast) and current time.
PART 1 • English 6.4 Selection Audio language Press AUDIo to select the audio language. Select Audio Channel or Sound mode with pq and Audio channel number or Sound mode (Stereo, Left or Right channel). Press oK to confirm your selection.
PART 1 • English Cause Remedy No picture The receiver can’t receive the signal Check the antenna cable, replace the cable, or connect the cable to the receiver tightly. Incorrect values of some tuner Set the values of the tuner parameters.