Page 1
Digital Free-To-Air Satellite Receiver SRT 6011 User Manual...
Page 4
Attachments — For your safety, and to avoid damaging the 2. The product has been exposed to water. product, use only accessories recommended by STRONG. 3. The product does not operate normally despite following Water and Moisture — Never use this product around water operating instructions.
PART 1 • English TABLE OF CONTENTS 1.0 INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Features & Accessories 2.0 YOUR RECEIVER 2.1 Front Panel 2.2 Rear Panel 2.3 Remote Control 3.0 CONNECTIONS 3.1 Connecting to TV & VCR 3.2 Connecting to Digital Audio Amplifier 3.3 Connecting to Satellite Dish 3.4 Connecting to serial cable for downloading software...
PART 1 • English 1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or near any other equipment that generates heat;...
PART 1 • English 1.3 Equipment Set-up We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and your antenna. Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver.
PART 1 • English Accessories: User’s Manual 1 Remote control unit 2x Batteries (AAA type) Note: The batteries should not be recharged, disassembled, electrically short-circuited or be mixed or used with other types of batteries. 2.0 YOUR RECEIVER 2.1 Front Panel 1.
PART 1 • English 9. S/PDIF Digital audio output Use this coaxial output to connect your receiver to the input of your digital audio amplifier. 10. Power ON/OFF Switch 2.3 Remote Control Turns the receiver On/Off Mutes audio output of the receiver Toggle between TV and AV mode 0 ~ 9 Changes channel and controls numeric functions...
PART 1 • English 3.0 CONNECTIONS 3.1 Connecting to TV & VCR Basic connection with a Scart cable Fig. 3 1. Connect the satellite signal from the LNB to the LNB IN connector. 2. Connect the TV SCART connector at the back of the receiver to the SCART IN connector on your TV set.
Ensure your satellite receiver is correctly connected to your television and dish, and that your satellite signal is of good quality. (If you are not sure about this then ask your local STRONG dealer to check your installation or satellite signal.) Confirm that the power plug on the receiver is plugged into the wall outlet.
PART 1 • English 4.3 Antenna mode a) Fixed dish Set Antenna mode to Fixed, select NEXT and press the OK button. The Adjust antenna screen appears, select transponder receivable at your location and adjust the antenna position for maximum level for the signal strength and quality.
PART 1 • English Edit (YELLOW button) Select the channel that you wish to edit, press the YELLOW (Edit) button to move into the modify program menu. In this menu, you can modify the Program Name, Down Frequency, Symbol rate, Video PID, Audio PID.
PART 1 • English Delete satellite If you want to delete a satellite, press the YELLOW key. Then warning message will appear. Select OK and press the OK key to confirm. 5.2.2 Auto Scan Press the GREEN key to set the scan mode to Free or Free+Scrambled. If mode is Free then only “Free to Air”...
Page 16
PART 1 • English 5.3.1 Preference 5.3.1.1 Language Setting You can change the language of the OSD, preferred Audio and Subtitles. Use UP/DOWN to select the OSD language, Audio language or Subtitles language. Press OK or Right to enter the language list and Press UP/DOWN to select the language. Press OK to confirm. 5.3.1.2 TV settings You can set the TV mode, Screen mode and Video output.
Page 17
PART 1 • English 5.3.3.2 Menu Lock Press OK to select whether you need the lock or not for the Menu, YES or NO, press OK to confirm. If the menu lock is on, then for some operations such as search program and set factory default, you need to enter your PIN.
PART 1 • English do not disconnect the receiver from the aerial during update process. Availability of the software update is subject of local broadcast condition and may not work in all countries. Contact your vendor to find out more about this function. 5.3.5.3 Update through PC to STB 1.
PART 1 • English Start Time: You can set the start time of the timer action. End Time: You can set the end time of the channel viewing when the Timer mode is on Time Interval. Channel Type: Select between TV and Radio. Channel name: Press the RIGHT button to display the channel list and using navigation buttons select the channel to be shown when the receiver will power on by the timer.
PART 1 • English 6.0 WATCHING TV AND LISTENING TO THE RADIO 6.1 Program Information In normal operation status (no menu operation), press the INFO button. The program information banner will be displayed at the bottom of screen. From program information banner you can read channel number, channel name, current and next program name (if available from broadcast) and current time.
PART 1 • English 6.5 Selection Audio Language Press the AUDIO button on the remote control to select the audio language. Select the Audio Channel or Sound mode with UP/DOWN buttons. Select Audio channel number or Sound mode (Stereo, Left or Right channel).
PART 1 • English Symptom Cause Remedy Message “Antenna Receiver detected short cut in Disconnect receiver from main power Power Overload” your cable system Check your cable system. remove short displayed on TV cut.Replace LNB. Restart receiver. The remote control The batteries of the remote Check whether the batteries are does not work...
Page 23
PART 1 • English 4. A/V & Data In/Out TV Scart Output: RGB, CVBS, Audio L/R Output with Volume Control VCR Scart Input/Output: Input: CVBS, Audio L/R Output: CVBS, Audio L/R Output with Volume Control 3 RCA Video and Audio output: Yellow: Video output;...
PART 1 • English A.3 GLOSSARY OF TERMS C band 3.7 ~ 4.2 GHz Frequency. DiSEqC Digital Satellite Equipment Control. A dish antenna that is aimed at one particular satellite. Fixed Dish Free-To-Air broadcast Unscrambled broadcast which you can view for free Ku band 11 ~ 13 GHz Frequency.
PART 7 Environmental Issues ü ENVIRONMENTAL ISSUES STRONG is committed to reducing the impact of its products on the environment. To maximise the benefits of our design enhancements, your co-operation is required. Electronic product recycling Packaging Do not dispose of this product with your When disposing of this domestic rubbish.