Operating and installation instructions EGW 2060 To avoid the risk of accidents or damage to the appliance it is essential to read these operating instructions before it is installed or used for the first time. M.-Nr. 06 155 840...
Warning and Safety instructions Technical safety Do not connect the appliance to the mains electrical supply by an Before connecting the appliance to extension lead. Extension leads do not the mains supply make sure that guarantee the required safety of the the voltage and frequency correspond appliance (e.g.
Warning and Safety instructions Correct usage During installation, maintenance and repair work, the appliance This appliance complies with all must be disconnected from the mains relevant legal safety requirements. electricity supply. The appliance is only Incorrect use can lead to personal completely isolated from the electricity injury and damage to property.
Warning and Safety instructions This appliance is not a toy! Do not Do not use the appliance to heat let children access the drawer or up the room. Due to the high its controls. Supervise its use by the temperatures radiated, objects near the elderly or infirm.
Caring for the environment Disposal of the packing Disposal of your old appliance material Old appliances contain materials which can be reclaimed or recycled. Please The transport and protective packing contact your dealer, your local waste has been selected from materials which collection centre or scrap merchant are environmentally friendly for disposal about available recycling schemes.
Before using for the first time General notes Cleaning for the first time The plate warmer is intended Before using for the first time, clean the exclusively for heating crockery. appliance with a damp cloth only and then wipe dry. The base of the drawer is fitted with a non-slip mat which stops crockery sliding about when the drawer is...
Operation Opening and closing the Do not use the appliance to re-heat, drawer cook or keep food or drinks warm. The drawer can be opened and closed Condensation from the food or by pressing lightly in the middle of the drinks could lead to corrosion in the drawer front.
Operation Using the drawer Selecting a temperature ^ Place crockery inside the drawer. The temperature control allows you to select any temperature between ca. 30 ^ Select the temperature required. and 50 °C. ^ Switch on the appliance (j). The temperature selector must only The switch lights up.
Operation Heating up times Capacity Various factors will affect the heating up The quantity that can be loaded will times: depend to a great extent on the type and size of your own crockery. – the material and thickness of the crockery Example –...
E-cloth – cleaning agents containing soda, acids or chlorides, A microfibre "E-Cloth" is available from the Miele UK Spare Parts Department, – abrasive cleaning agents, e.g. which is suitable for cleaning surfaces powder cleaners and cream such as stainless steel, glass, plastic...
Cleaning and care Non-slip mat Stainless steel fronts The appliance front is susceptible to The non-slip mat can be removed from scratches and abrasions. the drawer for cleaning. Stainless steel surfaces can be cleaned The mat is best cleaned by hand using using a proprietary non-abrasive warm water with a little washing-up cleaning agent designed specifically...
Problem solving guide . . . the crockery does not heat up. Installation work and repairs to Check whether, electrical components of this appliance must only be carried out – the mains fuse has blown. by a suitably qualified and If any of the following problems occur, competent person in accordance the advice of a qualified electrican or...
– Your Miele dealer, or – the Miele Service Department (see address on back cover). When contacting your Dealer or the Service Department, please quote the model and serial number of your appliance, which is given on the data plate.
Installation Safety instructions for This equipment may only be used in mobile installations such as installation ships, caravans, aircraft etc. if a risk Before connecting the appliance to assessment of the installation has been the mains supply make sure that carried out by a suitably qualified the voltage and frequency correspond engineer.
Installation ^ Build in the combination appliance in Positioning the appliance in accordance with its own specific the housing unit operating and installation ^ Push the appliance into the housing instructions. unit as far as the vapour strip and align it. Ensure that the housing unit is aligned at a right angle.
Installation Aligning the front of the plate warmer After building in the combination appliance, it may be necessary under certain circumstances to – align the front of the plate warmer – align the gap between the plate warmer and the combination appliance.
Installation Electrical connection If the socket is not accessible after installation (depending on country) an All electrical work should be carried additional means of disconnection must out by a suitably qualified and be provided for all poles. competent person in strict For extra safety it is advisable to install accordance with national and local a residual current device (RCD) with a...
Installation If the appliance is connected via a The fuse cover must be re-fitted when fused plug and switched socket the changing the fuse, and if the fuse cover colours of the wires in the mains lead of is lost, the plug must not be used until a this appliance may not correspond with suitable replacement is obtained.
Alteration rights reserved / 0904 M.-Nr. 06 155 840 / 00 en / GB This paper consists of cellulose which has been bleached without the use of chlorine.