Related Manuals for Miele EGW602-14
Summary of Contents for Miele EGW602-14
- Page 1 Operating and installation instructions Built-in plate warmer EGW 602 - 14 To prevent accidents and machine damage, read these instructions installation or use. M.-Nr. 05 478 600...
-
Page 2: Table Of Contents
Controls ............8 Warming dishes . - Page 3 This appliance is intended for resi- dential use only. Only use the appli- ance for its intended purpose. Improper use of the appliance can lead to personal injury and material damage. The manufacturer cannot be held responsible for damages caused by improper use of the plate warmer.
- Page 4 Return the ap- pliance to the nearest authorized servi- ce facility for service. Installation, repair and mainte- nance work should be by a Miele authorized service technician. Work by unqualified persons could be danger- ous and may void the warranty.
- Page 5 Children should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance. : Do not store items of interest to children in cabinets above or in the plate warmer.
- Page 6 The transport and protective packing materials are environmentally friendly for disposal and may be recyclable. Ensure that any plastic wrap is dis- posed of safely and kept out of the reach of babies and young children. Danger of suffocation! Please recycle. Old appliances contain materials which can be recycled.
- Page 7 a On/Off button b Temperature control c Warming drawer d Non-slip mat e Rail f On/Off indicator light...
-
Page 8: Controls
The plate warmer is only intended for Do not use the plate warmer to re-heat, cook or keep food or drinks warm. Condensation from food or drinks could cause moisture dam- age to the appliance. The appliance operates with a . -
Page 9: Warming Dishes
Procedure in brief: ^ Place the dishes in the warming drawer. ^ Select the desired temperature set- ting. ^ Turn on the appliance (j). ^ Close the drawer. The indicator on the front of the appli- ance lights up to show that the appli- ance is on. -
Page 10: Selecting A Temperature
just the temperature setting. Only turn the temperature control clockwise and then back again. Stop when you feel a resistance. Forcing the control past this point will damage it. The heat will shut off automatically when the selected temperature is reached. -
Page 11: Cleaning The Exterior
Never use abrasive cleaners, scour- ing pads, steel wool or caustic (oven) cleaners on the plate warmer. They will damage the surface. The exterior of the plate warmer can be cleaned with warm water and liquid dish soap applied with a soft sponge. Wipe dry using a soft cloth. - Page 12 As you use the plate warmer you will learn which setting suits your needs best. If any of the following problems occur, please contact your Miele dealer or the nearest Miele Technical Service Depart- ment. Check – whether the noise of the fan can be heard.
- Page 13 In the event of a fault which you cannot correct yourself please contact: – Your Miele Dealer – The Miele Technical Service Department 1-800-999-1360 techserv@mieleusa.com 1-800-565-6435 service@miele.ca When contacting the Technical Service Department, please quote the model and serial number of your appliance both of which are shown on the data plate which is next to the control panel.
- Page 14 The electrical installation instructions for any appliance installed in combi- nation with the plate warmer must be observed. When another appliance is installed in combination with the plate warmer to the same circuit breaker, operat- ing both appliances at the same time could cause an overload.
-
Page 15: Steam Oven
The plate warmer may only be installed beneath one of the following Miele ap- pliances: – Steam oven (DG 155) – Coffee machine (CVA 610) Read all the operating and installa- tion instructions for any other appli- ance installed in combination with the plate warmer. - Page 16 The plate warmer must be installed above a fixed interim shelf within the cabinet to ensure that the cabinetry can support the weight of it and of any other appliance installed in combination with it. When installed in combination with another appliance, the plate warmer must always be installed beneath the other appliance.
-
Page 17: Aligning The Front Of The Plate Warmer
^ Remove the protective foil from the adhesive strips. ^ Align the metal strips flush against the side and rear walls of the cabinet a and stick them on to the plate warmer b (see illustration). The third metal strip is not needed if the cabinetry does not have a rear panel. - Page 20 Alteration rights reserved / 22 / 001 USA / CDN - 3401 M.-Nr. 05 478 600 (EGW 602 - 14) This paper consists of cellulose which has been bleached without the use of chlorine.