Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Miele ESW 4088-14
Summary of Contents for Miele ESW 4088-14
-
Page 1: Esw 48X2
Operating and Installation Instructions Built-in Warming Drawer ESW 4082-14 ESW 4088-14 ESW 47x2 ESW 48x2 en - US, CA To prevent accidents and machine damages, read these instructions before installation or use. M.-Nr. 07 342 380... -
Page 2: Table Of Contents
ESW 4082-14 / ESW 4088-14 ........ -
Page 3: Important Safety Instructions
WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. Keep these operating instructions in a safe place and pass them on to any future user. - Page 4 Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. Do not operate any appliance with a...
- Page 5 Safety Protect your hands with oven mitts or potholders when using the appliance. Use only dry, heat resistant potholders. Moist or damp potholders used on hot surfaces can result in steam burns. Be aware of loose fitting or hanging clothing while using the warming drawer.
- Page 6 IMPORTANT SAFETY INSTRUCTIONS The use of accessories not recommended by Miele may cause injury. Make certain that the power cords of small appliances do not come in contact with the appliance. The insulation of the cable could become damaged. Danger of electric shock! Do not lean, sit or overload the warming drawer.
-
Page 7: Guide To The Warming Drawer
Guide to the warming drawer ESW 4082-14 / ESW 4088-14 Control panel Non-slip mat... -
Page 8: Esw 47X2 / Esw 48X2
Guide to the warming drawer ESW 47x2 / ESW 48x2 Control panel Non-slip mat Vent Rack... -
Page 9: Control Panel
Control panel On/Off Press and hold this touch control to turn the warming drawer On and Off Menu Allows you to select the operating mode Operating modes: Cups/glasses Tableware Food - warm and hold Guide to the warming drawer Temp. Allows you to select the desired temperature. -
Page 10: Before The First Use
Before the first use When first connecting the appliance to the power supply and after a power failure, the fan will run and a display test will be carried out for approx. 10 seconds. The appliance cannot be used during this time. Clean the appliance ^ Remove any protective wrapping. -
Page 11: Using The Warming Drawer
Operating modes Tap the "Menu" touch control until the desired operating mode lights: – / Cups/Glasses – H Tableware – 2 Food - warm and hold The last operating mode selected appears in the control panel when the drawer is turned on. The warming drawer is equipped with a fan which distributes warm air throughout the drawer. -
Page 12: Temperature Settings
Using the warming drawer Temperature settings Each operating mode has an assigned temperature range. The suggested temperatures are set by default, they are marked in bold in the table below. Use the "Temp." touch control to change the setting in increments. The last selected temperature is shown in the control panel the next time the warming drawer is turned on. -
Page 13: Duration
Duration The warming drawer is set for continuous operation by default. By selecting the "Timer" touch control a warming time can be set. With each tap of the "Timer" touch control the duration will increase in one hour increments, beginning with 1 hour and ending with 4 hours. -
Page 14: Sabbath Mode
Using the warming drawer Sabbath Mode For religious observance, the appliance can be set for the duration of the Sabbath. In Sabbath mode the timer is deactivated and the sensors have to be touched longer than ususal. If Sabbath mode is activated, the appliance will turn off after approx. -
Page 15: Loading The Warming Drawer
Do not overload the drawer. To increase the load space use the supplied rack. Two racks will fit in the drawer at one time. Additional racks are available from Miele. ESW4082-14 / ESW 4088-14 ESW 47x2 / ESW 48x2 Loading the warming drawer... -
Page 16: Keeping Food Warm
Keeping food warm Tips The warming drawer is intended for keeping food warm directly after preparation. It is not intended to re-warm cold meals. – To ensure that the minimum temperature of 150°F (65°C) required to keep food warm is met, select 2. –... - Page 17 Settings Food Bacon Beef** Rare / Medium / Well Bread hard rolls Bread soft rolls Casserole, crisp top Casserole dish Casserole, moist Eggs, hard boiled Scrambled eggs Fish / Seafood Fruit Gravy, cream sauces Lamb Oatmeal** Pancakes Pies - Single Crust Baking Dish Pies - Double Crust Baking Dish...
-
Page 18: Warming Tableware
Warming tableware Tips – Distribute tableware throughout the entire drawer. Stacked plated will heat up more slowly than individual pieces. If stacking is unavoidable please them in the front of the drawer. Use the rack (depending on model). – Do not place platters right up against the vents. -
Page 19: Other Usages
The warming drawer can also be used to proof yeast dough or to warm or crisp bread. Proofing dough ^ Open the drawer. ^ Turn the appliance on "On/Off". ^ Touch "Menu" to select the " / Cups/Glasses" setting. ^ Touch "Temp." to select the ] ^ ^ ^ ^ temperature setting. -
Page 20: Cleaning And Care
Cleaning and care Allow the appliance to cool before cleaning. Do not use a steam cleaner to clean this appliance. Pressurized steam could penetrate electrical components and cause a short circuit. Do not use commercial cleaning agents. Only use agents recommended for domestic use. -
Page 21: Frequently Asked Questions
Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. What if the drawer does not heat? Possible fault There is no power to the warming drawer. -
Page 22: Technical Service
Miele Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home. -
Page 23: Installation Instructions
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use. -
Page 24: Important Safety Instructions
Please contact the Miele Technical Service Department with specific requirements. ESW 4082-14 / ESW 4088-14 Only install the warming drawer in combination with built-in appliances recommended by the manufacturer. When installed with other appliances,... -
Page 25: Esw 4082-14 / Esw 4088-14
Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Combination possibilities Installation with an oven Cut-out for venting the oven * Machine with glass front ** Machine with stainless steel front... - Page 26 ESW 4082-14 / ESW 4088-14 Installation with a steam oven * Machine with glass front ** Machine with stainless steel front Installation with a coffee machine * Machine with glass front ** Machine with stainless steel front...
-
Page 27: Esw 47X2
ESW 47x2 Solo installation Side view A base is required for solo installations... - Page 28 ESW 47x2 Installation with an oven Side view with oven...
-
Page 29: Esw 48X2
ESW 48x2 Solo installation Side view A base is required for solo installations... - Page 30 ESW 48x2 Installation with an oven Side view with oven...
-
Page 31: Installation
Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Check that the base of the warming drawer is clean and level. Only then will it function properly. When inserting the appliance, wear work gloves to avoid injuries. -
Page 32: Aligning The Appliance Front
^ Carefully lift the control panel out of the drawer. Be careful not to pull or damage the power cord. ESW 4082-14 / ESW 4088-14 ESW 47x2 / ESW 48x2 from the left and right sides of the... - Page 33 ^ Tighten the screws on the inside of the drawer front. ^ Replace the control panel, use caution with the power cord. ^ Replace the screws on the left and right sides of the drawer front. ESW 4082-14 / ESW 4088-14 ESW 47x2 / ESW 48x2...
-
Page 34: Integrated Installations
Installation Integrated installations Custom made front panels can be installed with models ESW 4702 FB and ESW 4802 FB. The custom panel must be at least made of heat resistant material 140 °F (60 °C). The front panel, including handle, must not exceed 11 lb (5 kg) in weight. - Page 35 ^ Remove the cable tie from the panel. ^ Screw the removed panel to the custom panel (see illustration). ^ Hook the panel into the bottom. Make sure the seal is seated correctly. ^ Replace and slightly tighten the screws on the inside of the drawer front.
-
Page 36: Electrical Connection
Electrical connection CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. -
Page 37: Help Protect Our Environment
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Help protect our environment Disposal of an old appliance Old appliances contain materials that can be recycled. - Page 40 Alteration rights reserved / 0410 M.-Nr. 07 342 380 / 06 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
Need help?
Do you have a question about the ESW 4088-14 and is the answer not in the manual?
Questions and answers