Changing The Network Settings - Panasonic SC-PTX7 Operating Instructions Manual

Changing the network settings

These settings are used if you will connect this unit to a
network.
Preparation
1 To display the picture turn on the television and
select the appropriate video input to suit the
connections to this unit.
Press .
2 [Í]
Common procedures
1
Press [SETUP].
2
Press [3 4] to select "Other Setup" and press
[ENTER].
3
Press [3 4] to select "Network" and press [1].
4
Press [3 4] to
select "Network
Settings" and
press [ENTER].
The network connection status is displayed.
Manually setting the IP address
In most cases, default settings can normally be used
without making any changes.
When connecting this unit to a network and assigning a
fixed IP address, perform the following settings.
After performing steps 1–4 (➜ above)
5
Press [3 4] to select "TCP/IP 1" and press
[ENTER].
6
Press [3 4] to select "IP Manual Setting" and
press [ENTER].
7
Press [3 4] to
select the item to
be set and press
[ENTER].
8
Enter numbers with the numbered buttons and
press [ENTER].
≥After checking the specifications for your
broadband router, enter each number.
≥The numeric input range is between 0 and 255.
Repeat steps 7–8, and enter numbers for other items.
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
If you made an input mistake
Move the cursor with [2 1] and make corrections with
the numbered buttons.
To delete settings and use default settings
Select "IP Auto Setting" in step 6 and press [ENTER].
96
Network Settings
TCP/IP 1
Auto Setting
TCP/IP 2 Auto Setting
IP Address
Connected to network.
IP Manual Setting
IP Address 0. 0. 0. 0
Subnet Mask
0. 0. 0. 0
Gateway
0. 0. 0. 0
Manually setting the DNS server
In most cases, default settings can normally be used
without making any changes.
When setting an assigned DNS server from your ISP,
perform the following settings.
After performing steps 1–4 (➜ left)
5
Press [3 4] to select "TCP/IP 2" and press
[ENTER].
6
Press [3 4] to select "DNS Manual Setting"
and press [ENTER].
≥If "TCP/IP 1" is set to "IP Manual Setting", the
"DNS Auto Setting" will not be displayed.
7
Press [3 4] to
select the item to
be set and press
[ENTER].
8
Enter numbers with the numbered buttons and
press [ENTER].
≥Follow the instructions given by your ISP and
enter the numbers.
≥The numeric input range is between 0 and 255.
Repeat steps 7–8, and enter numbers for other
items.
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
If you made an input mistake
Move the cursor with [2 1] and make corrections with
the numbered buttons.
To delete settings and use default settings
Select "DNS Auto Setting" in step 6 and press [ENTER].
To check the IP Address, etc.
After performing steps 1–4 (➜ left)
5
Press [3 4] to
select "IP Address"
and press
[ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
DNS Manual Setting
Primary DNS Address
0. 0. 0. 0
Secondary DNS Address 0. 0. 0. 0
IP Address
[MAC Address] 00-00-00-00-00-00
[IP Address] ---.---.---.---
[Subnet Mask] ---.---.---.---
[Gateway] ---.---.---.---
[Primary DNS Address] ---.---.---.---
[Secondary DNS Address] ---.---.---.---