• 22"(55.9 cm) B ackguard withShelf f or30"(76.2 cm)
Order P art N umber W10225950
• 22"(55.9 cm) B ackguard withShelf f or36"(91.4 cm)
Order P art N umber W10225949
• 22"(55.9 cm) B ackguard withShelf f or48"(121.9 c m)
Order P art N umber W10225948
Toorder, seethe"Assistance orService" section o ftheUse
Additional Parts Needed on Steam-Assist
1¼,, O .D. flexible codes approved water supply tubing (to
make water connection)
Water connection device (to connect 1¼,, O .D. tubing to
water source). Check local codes for type of connection
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See "Electrical Requirements"
"Gas Supply Requirements"
It is recommended
that all electrical connections
be made by a
licensed, qualified electrical installer.
High Altitude Conversion
To convert the cooktop for elevations above 6,560 ft (1999.5 m),
order a High Altitude Conversion
Part Number W10237848 - LP high altitude
Part Number W10160841 - Natural gas high altitude
To order, see the "Assistance
or Service" section of the Use and
Ii, ()Ci,;!II]I()I,_I,, I]_
_'_"_ _ -"I lq
IMPORTANT: Observe all governing codes and ordinances.
not obstruct flow of combustion
and ventilation air.
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
rating plate is located on the right vertical
surface of the oven door frame.
It is recommended
that a 600 CFM or larger range hood be
installed above the range.
It is not recommended
that a microwave hood combination
be mounted above the range.
Recessed installations must provide complete enclosure of
the sides and rear of the range.
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
All openings in the wall or floor where range is to be installed
must be sealed.
Do not seal the range to the side cabinets.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see "Install Anti-Tip Bracket"
Grounded electrical supply is required. See "Electrical
Proper gas supply connection must be available. See "Gas
Supply Requirements" section.
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C). Use an
insulated pad or 1¼,, ( 0.64 cm) plywood over carpet and under
range if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance
with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures
of 194 ° (90°C).
Mobile Home - Additional
The installation of this range must conform to the Manufactured
and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-1atest
edition, or with local
Mobile home installations
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
30" (76.2 cm) models
A. Optional backguard may be installed
B. 273/4" (70.5 cm) depth with control panel, see NOTE*
C. 353/4'' (89.6 cm) cooktop height when setting on the wheels
D. 293/4'' (101.0 cm) width
rating plate location