Electrical Requirements - Canada Only; Gas Supply Requirements - KitchenAid JES1750FS Installation Instructions Manual

Electrical Requirements – Canada Only
WARNING
Electrical Shock Hazard
Electrically ground range.
Failure to do so can result in death, fire, or
electrical shock.
Be sure that the electrical connection and wire size are
adequate and in conformance with the CSA Standard C22.1,
Canadian Electrical Code, Part 1 – latest edition, and all local
codes and ordinances.
A copy of the above code standards can be obtained from:
Canadian Standards Association
178 Rexdale Blvd.
Toronto, ON M9W 1R3 CANADA
C heck with a qualified electrical installer if you are not sure
■
the range is properly grounded.
Range Rating*
120/240 Volts 120/208 Volts
8.8–16.5 kW 7.8–12.5 kW
16.6–22.5 kW 12.6–18.5 kW
* The NEC calculated load is less than the total connected load listed
on the model/serial/rating plate.
W hen a 4-wire, single phase 240 volt, 60 Hz., AC only
■
electrical supply is available, a 40-amp minimum circuit
protection is required on 30" (76.2 cm) ranges, fused on
both sides of the line.
A time-delay fuse or circuit breaker is recommended.
■
T his range is equipped with a UL or CSA International
■
Certified Power Cord intended to be plugged into a
standard 14-50R wall receptacle. Be sure the wall
receptacle is within reach of range's final location.
D o not use an extension cord.
■
T he wiring diagram is located on the back of the range
■
or in a clear plastic bag.
10
Specified Rating of
Power Supply Cord Kit
and Circuit Protection
Amps Temp Rating
40 or 50 194°F (90°C)
50 194°F (90°C)

Gas Supply Requirements

WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local
codes and ordinances. In the absence of local codes,
installation must conform with American National Standard,
National Fuel Gas Code ANSI Z223.1 – latest edition or CAN/
CGA B149 – latest edition.
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturer's instructions.
Type of Gas
Natural Gas:
T his range is factory-set for use with Natural gas. See "Gas
■
Conversions" section. The model/serial/rating plate located
on the oven frame behind the top right-hand side of the
oven door has information on the types of gas that can be
used. If the types of gas listed do not include the type of
gas available, check with the local gas supplier.
LP Gas Conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the
gas specified on the model/serial/rating plate for use with
a different gas without consulting the serving gas supplier.
See "Gas Conversions" section.
Gas Supply Line
P rovide a gas supply line of ¾" (1.9 cm) rigid pipe to the
■
range location. A smaller size pipe on longer runs may
result in insufficient gas supply. With LP gas, piping or
tubing size can be ½" (1.3 cm) minimum. Usually, LP gas
suppliers determine the size and materials used in the
system.
NOTE: Pipe-joint compounds that resist the action of LP
gas must be used. Do not use TEFLON
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
tape.
®†