Download Print this page

Safety Precautions - Haier HWM70-0588 User Manual

Environmental-friendly double drive washing machine

Advertisement

Safety precautions

Please plug the power plug on special
so that the plug is accessible. Be sure to pull the
receptacle. Be sure to use three-pins
plug off and close the water faucet in
power receptacle. Ensure that the earthing
following cases: power failure, delivering
the machine, setting the machine idle or
prong of the power receptacle is earthed
c l e a n i n g t h e m a c h i n e . D o n o t p l u g
reliably. Use leakage protector if possible.
or pull the power plug with wet hand.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by
the technicians of our special shop or our customer care agent.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
T h e v e n t i l a t i o n
holes at the bottom
Carpet
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
2
The washing machine must be positioned
Do not use water hotter than 50 .
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. Do not repair it by yourself.
Phenomena
The reason
The digitron displays E0.
The top lid is opened during reserve procedure.
The drainage cannot work, or is too slow.
Is the drain hose put down?
Is the drain hose blocked?
The digitron displays E1.
It stops running in midway. The digitron
The top lid is not closed.
displays E2.
The safety switch acts, and the
Are the laundries put slantingly?
spinning cannot work. The
Is the machine slanting?
digitron displays E3.
Is the water tap opened, or is there water
The water filling does not work, or is
supply failure?
slow. After about 15 minutes later,
Is the water inlet valve blocked?
the digital displays E4.
Is the water pressure too low?
The digitron displays E6.
The water level sensor is bad.
The digitron displays E7.
The communication is bad.
Is there power failure?
Not wash
Is the power plug inserted tightly?
The machine does
Is the water level reached preset position?
not act
Is the power plug inserted tightly?
Not spin
Is the top lid closed reliably?
Are the laundries set flat?
Is the machine slanting?
There's abnormal sound
Are the laundries put slantingly in spinning?
inside the machine
Are there any foreign materials?
Is the screw of the jointer of water
The water tap leaks
inlet hose loose or awry?
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The wash procedure is paused.
The program is setting the drain time. Some time is needed
Push the PROGRAM button to select SPIN,
but it doesn't work.
before it starts spinning.
The pulsator pauses during water inlet
It is to avoid splashing during water inlet.
in wash and rinse.
There may be some water flowing out of the
It is the water remained in the factory inspection of performance.
drain hose in the first use of the machine.
How to settle
Close the top lid.
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
Close the top lid.
Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the Start/Pause button once.
Push the Start/Pause button once.
Please contact the after-sales
service department.
Please contact the after-sales service
department.
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.

Advertisement

loading

This manual is also suitable for:

Hwm70-0588h