Related Manuals for Haier HWM70VA
Summary of Contents for Haier HWM70VA
-
Page 1: Table Of Contents
Preparation before washing The musts in washing Usage of the detergent 8-10 Washing sequence Disposal after washing 11-13 Trouble-Shooting Answers to question 14 Specification SEMI AUTO WASHING MACHINE Please read this manual carefully before using Retain it for future reference Model HWM70VA... -
Page 2: Names Of The Parts
Names of the parts Valve cover Meaning and description of the symbols Contents marked with that s ymbol are r elated to the sa fety of the product a nd the per sonal Warning sign safe ty of the users. P lease ope rate in strict conformity to the co ntents, otherwise it may cau se da mage of the ma chine or in jure the pers onal s afety of the use r. -
Page 3: Safety Precautions
× Safety precautions Please insert the power cord into When the machine is normally special receptacle with rated vol- using, please put the power plug tage.Be sure to use single-phase at the location easily to be insert- three pins receptacle.The earthing ed and extracted by hand. - Page 4 × Safety precautions Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children. Do not put any hot or heavy items Do not wash laundries with volatile ( such as the kettle with hot water ) materials (such as thinner, petrol etc.).
-
Page 5: Installation And Adjustment
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package,please take out the lint filter from the document bag,install it to the overflow filter of the wash tub.See to the figure. -
Page 6: How To Change The Direction Of The Drain Hoses
How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Soft item Extend the drain hose from the side of wash tub. Figure 1 Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. -
Page 7: Preparation Before Washing
× Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose . -
Page 8: The Musts In Washing
The musts in washing The capacity of washing and spinning of the machine refer to the weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the standard capacity. -
Page 9: Washing Sequence
Washing sequence Spin timer Wash selector Wash timer (To set to below 2 minute, (Strong current, (to set to below 1 minute, first set to 5 minute then standard current) first set to 2 minute then turn it back. it can increase turn it back. - Page 10 Midway spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Push Proper The laundries Proper No gland are slanting (2) Close the inner and outer cover of the spin tub.
-
Page 11: Rinse With Water-Filling
Rinsing Rinse with water-filling 1.Put the laundries into the wash tub. Select OVERFILL suitable current according to the laundries. 2.Adjust the water level If you find water flo- wing out here,please Set the water level with water level adjusting twist the water tap to limit the water filling. -
Page 12: Disposal After Washing
Disposal after washing After using, please clean the lint and eyewinker of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. -
Page 13: Cleaning The Overflow Filter
Cleaning the overflow filter 2. Take off the corrugation pipe. Water level Dismantle the upper part of the adjusting lever corrugation pipe inside overflow filter ( as indicated in Corrugation Figure 1). Pipe 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. - Page 14 protective cover Cleaning the 2.cleaning dirty under the protective cover take out the sundries using the plier or other wiry 3.install the protective cover after cleaning, install it as origin assure it reliable Disposal of the complete unit After washing, dismount the water inlet Wipe the complete unit with soft hose.
-
Page 15: Trouble-Shooting Answers To Question
Trouble-shooting Answers to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.