Carrier KGANP5201VSP Installation Instructions Manual page 20

f
CONVERSION KiT RATING PLATE CARRIER CORPORATION
THiS APPLIANCE HAS BEEN CONVERTED TO USE PROPANE GAS FOR FUEL, REFER TO KiT iNSTRUCTiONS FOR CONVERSION
PROCEDURES. USE PARTS SUPPLIED BY CARRIER CORPORATION AND iNSTALLED BY QUALiFiED PERSONNEL.
SEE EXiSTiNG RATING PLATE FOR APPLIANCE MODEL NO. AND iNPUT RATING.
NOTE: Furnace gas input rate on rating plate is for installations up to 2000 ft. (610m) above sea level In U,S.A. the input rating for altitudes above 2000 ft, (610m) must
be derated by 4% for each 1000 ft. (305m) above sea [eveL in Canada the input rating must be derated by 10% for aRitudes of 2000 ft. (610m) to 4500 ft. (1372m) above sea [eveL
KiT NO.: KGANP5201VSP FUEL USED: PROPANEGAS iNLET PRESSURE (rain - raax): 11.0- 13.6 in. wc
(SUPERSEDES: KGANP4601ALL, KGANP4101ALL, KGANP4001ALL, KGANP3001ALL, KGANP2901ALL)
ALTITUDE OF INSTALLATION (FT. ABOVE SEA LEVEL) U.S.A. *
APPLIANCE
0 2001 * 3001 4001 5001 6001 7001 8001 9001
MODELS to 2000 to 3000 to 4000 to 5000 to 6000 to 7000 to 8000 to 9000 to 10000
Orifice 55 1.30mm 1.30ram i1.25mm 1.25mm 1.25mm 56 56 56
No,
58CVA, 58CVX Manifold Pressure I_
,o, o oleo[o olo l o11.o I
PG8JVA, PGSMVA LOW 5.8 I 5.3 5.0 5.5 5.2 4.9 5.7 5.2 4.8
_. * For Canadian installations from 2000 to 4500 ft. (610ra to 1373ra) use U.S.A. column 2001 to 3000 ft. (611ra to 914ra). 337704-204 R EV. D
Al1636
Fig. 37 - Conversion Kit Rating Plate
1337932-7021
CONTAINS: QTY
PART # DESCRIPTmON
328456-401 BIT, DRILL 1
327593-401 SCREW 7
REQUIRED FOR CONVERSION OF
NON CONDENSING GAS FURNACE
TO PROPANE GAS.
Fig. 38 - Gas Conversion Kit
\ i
I
I
--_l 1-9/16"
1
39.7 ram
Fig. 39 - Mixer Screw Location
A11397
Drill out with
5/64" drill bit.
A06432
Fig. 40 - Igniter Position - Side View
5/16"
7.9mm
A05025
REINSTALL BURNER ASSEMBLY
To reinstall burner assembly:
1. Attach flame sensor to burner assembly.
2. Install HSI and bracket to burner assembly.
3. Insert one-piece burner in slot on sides of burner box and
slide burner back in place.
4. Reattach HSI wires to HSI.
5. Verify igniter to burner alignment.
6. For Silicon Nitride igniters, see Fig. 40 and 41.
7. For Silicon Carbide igniters, see Fig. 42.
8. Re-attach Flame sensor wire to Flame Sensor.
2O