Design Information
BEFORE YOU BEGIN
Read
these
instructions
completely
and
carefully.
" IMPORTANT
- S.vethese instructions for
local inspector's
use.
• IMPORTANT
- Observe .ll
governing
codes
and ordinances.
• Note to Installer
- Be sure to leave these instructions
with the Gonsumer.
• Note to Consumer
- Keep these instructions
for
fitture reference.
• Skill Level - Installation
of this vent hood requires
basic mechanical
and electrical skills.
• Completion
time - 1 to 3 hours.
• Proper installation
is the responsibili D, of the installer.
• Product failure due to improper
installation
is not
covered under the _¥arranty.
CAUTION:
Due to the weight
and size of tiffs vent hood
and
to
reduce
the risk of personal
ii_jury or damage
to the
product,
we recommend
at least three
people
install
this hood.
PRUDENCE:
]_ cause
du poids
et de la mille de la hotte
et pour
r_duire
les risques
de blessures
ou de dommages
de
l'dquipement,
nous
recommandons
que trois personnes
installent
cette hotte.
WARNING:
To reduce the risk of fire or electrical shock, do not use
tiffs range hood with any external
solid-state speed
conuol
device. Any such alteration
flom original factory
wiring could result in damage to the unit and/or
create
an electrical safety hazard.
AVERTISSEMENT
:
Pour
rdduire
le risque
d'incendie
ou de choc
41ecuique,
il tie faut pas u6liser
cette hotte
avec un rdgulateur
de
vitesse dlectronique
externe.
Toute
modification
de ce
type du branchement
d'usine
peute
endommager
l'appareil
ou crder
un risque
de choc dlecuique.
TO REDUCE
THE RISK OF FIRE, USE ONLY
METAL
DUCTWORK.
2
WARNING:
TO REDUCE THE RISK OF HRE, ELECTRICAL
SHOCK OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
A. Use tiffs unit only in the manner
intended
by the
manufacturer.
If you have any questions,
contact the
InaI]
tl fac tit re t.
B. Before servicing or cleaning
unit, switch power off at
the service panel and lock service panel to prevent
power flom being switched on accidentally.
If the
service panel cannot be locked, fasten a mg or
prominent
warning label to the panel.
AVERTISSEMENT
:
POUR RI_DUIRE LE RISQUE D'INCENDIE, DE
CHOC I_LECTRIQUE
OU DE BLESSURES, IL FAUT
OBSERVER LES REGLES SUIVANTES :
A. Ufiliser cet appareil uniquement
de la mani_re
pr_vue pax le fabricant.
En cas de question,
consulter
le fabricant.
B. Avant toute intervention
ou nettoyage,
couper
l'alimentafion
dlecuique
au disioncteur
et
verrouiller
le panneau
du disjoncteur
pour dviter la
mise sous tension accidentelle.
S'il n'est pas possible
de verrouiller
le panneau
du disconcteur,
atmcher
un placard
ou une _fiquette u_s visible au panneau.
• For general ventilating
use only. Do not use to exhaust
hazardous
or explosive materials or vapors.
• Structural
flaming,
installation
work and electrical
wiring must be done by qualified person (s). In
accordance
with all applicable
codes and standards
including
fire-rated
consuucfion.
• Sufficient
air is needed
for proper combustion
and
exhausting
of gases through
the flue (chimney)
of fuel
burning
equipment
to prevent back drafting. Follow
the heating equipment
manufacturer's
guideline
and
safety standards
such as those published
by the
National Fire Protection
Association
(NFPA), and the
American
Society for Heating, Refligerafion
and Air
Conditioning
Engineers
(ASHRAE), and the local
code attthorifies.
• I,ocal codes vary. Installation
elecuical
connections
and grounding
must comply with applicable
codes.
In the absence of local codes, tim vent should be
installed
in accordance
with National Elecuical
(;ode
ANSI/NFPA
70-1990 or latest edition.
CAUTION:
t-ed.ce
t-isk o .te a.d to
properly
exhaust air, be sure to duct air outside--Do
not vent exhaust air into spaces within walls or ceilings
or into attics, crawl spaces, or garages.
PRUDENCE •
• I1faut prendre
soin
d'insmller
un conduit vers l'ext_rieur
pour r_duire le
risque d'incendie
et pouvoir _vacuer l'air correctement.
I1 ne faut pas _vacuer l'air correctement.
I1 ne faut pas
_vacuer l'air dans l'espace enue les parois d'un i_lttr,
un plafond
ou un greniet,
un espace sanitaire
ou un
garage.
Need help?
Do you have a question about the Monogram ZV1050 and is the answer not in the manual?