GE Monogram ZV1050 Installation Instructions Manual
42" island vent hood
Hide thumbs
Also See for Monogram ZV1050:
- Installation instructions manual (16 pages) ,
- Owner's manual (12 pages) ,
- Use and care manual (14 pages)
Related Manuals for GE Monogram ZV1050
Summary of Contents for GE Monogram ZV1050
- Page 1 Installation Instructions If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com 42" Island Vent Hood Model: ZV1050 Monogram. ® We bring good things to life.
-
Page 2: Design Information
Design Information BEFORE YOU BEGIN WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL Read these instructions completely and carefully. SHOCK OR INJURY TO PERSONS, OBSERVE THE • IMPORTANT - Save these instructions for FOLLOWING: local inspector’s use. A. Use this unit only in the manner intended by the •... -
Page 3: Table Of Contents
Design Information CONTENTS Design Information Product Dimensions ............3 Step 2, Remove Packaging ..........8 Duct Cover Accessories ............ 3 Step 3, Check Installation Hardware ....... 8 Product Clearances ............3 Step 4, Mount Template ........... 9 Advance Planning Step 5, Install Support Frame .......... 9 Tools and Materials Required .......... -
Page 4: Advance Planning
Advance Planning TOOLS AND MATERIALS REQUIRED POWER SUPPLY (not supplied) IMPORTANT - (Please read carefully) • Tape measure WARNING: • Knife FOR PERSONAL SAFETY, THIS • Spirit level APPLIANCE MUST BE PROPERLY GROUNDED. • Wire cutter ATTENTION – • Wire stripper POUR DES RAISONS DE •... -
Page 5: Duct Fittings
* Actual length of straight duct plus duct fitting equivalent. Equivalent length of duct pieces are based Total Duct Run on actual tests conducted by GE Evaluation Engineer- ing and reflect requirements for good venting performance with any ventilation hood. -
Page 6: Installation Instructions
Installation Instructions STEP 1 ADVANCE PLANNING Ceiling Plan the location Hood Determine the exact location of the vent hood. Ducting Centerline • Use a plumb bob to check location to be sure countertop/cooktop location below the hood will align exactly. •... -
Page 7: Ductwork
Installation Instructions STEP 1 CONTINUED 2x 4 Min. Cross Framing • Arrange cross framing in the ceiling to suit the existing structure. See examples. – Secure each 2 x 4 block with at least four (4), #10 wood screws, 3” long (not supplied). Use 8 wood screws total for the two supports. -
Page 8: Step 2, Remove Packaging
Installation Instructions STEP 2 REMOVE THE PACKAGING The vent hood is packed separate from the decorative duct cover or accessory covers ZX1059SFSS or ZX10510SFSS. • Remove the frame, cover, parts box and packaging. • Remove junction box cover. • Install strain relief onto junction box cover. STEP 3 CHECK INSTALLATION HARDWARE Locate the hardware accessory pack shipped with the hood and check contents. -
Page 9: Installation Instruction
Installation Instruction STEP 4 MOUNT TEMPLATE • Align the template with the marks on the ceiling and tape in place. – Be sure the template is oriented correctly, with the front of the hood. • Use a plumb to check to be sure the mounting holes will provide parallel alignment with the countertop below. -
Page 10: Step 6 Secure Wiring
Installation Instructions STEP 6 SECURE WIRING STEP 7 SIZE AND INSTALL DUCTWORK • Route house wiring through the ceiling hole and pull a length to reach the hood junction box, Ceiling approximately 6” below the support. Ceiling House Duct Left Side View Required Side... -
Page 11: Step 8 Install Decorative Duct Covers
Installation Instructions STEP 8 INSTALL DECORATIVE DUCT COVERS Install Screw on Top Duct Each Side Cover Pretap Bottom Duct Cover 2 Screw Bottom Duct Holes Top Duct Cover (One Cover Each Side) Top Duct Cover Stop Install Stop Screw Screw in Hole of Upper (Inner) Duct Cover •... -
Page 12: Step 10 Connect Electrical
Installation Instructions STEP 11 SLIDE DUCT COVER DOWN STEP 10 CONNECT ELECTRICAL Verify that power is turned off at the source. WARNING: If house wiring is not 2-wire with a ground wire, a ground must be provided by the Install installer. -
Page 13: Step 12 Install Filters, Finalize Installation
Installation Instructions STEP 12 INSTALL FILTERS, FINALIZE INSTALLATION Filter Slots • Remove protective film on the filters. • Tip the filter into the lower slots at the rear of the opening. Lift the filter and pull the knob forward until the filter rests on the slots. •... - Page 14 Notes...
- Page 15 Notes...
- Page 16 Note: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Monogram.