Download Print this page

GE Monogram ZV1050 Installation Instructions Manual

42" island vent hood
Hide thumbs Also See for Monogram ZV1050:

Advertisement

Installation
Instructions
42" Island
Vent Hood
Model:
ZV1050
Monogram:
We bring good things to life.

Advertisement

loading

Summary of Contents for GE Monogram ZV1050

  • Page 1 Installation Instructions 42" Island Vent Hood Model: ZV1050 Monogram: We bring good things to life.
  • Page 2 Design Information BEFORE YOU BEGIN WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL Read these instructions completely mid carefully. SHOCK OR INJURY TO PER.SONS, OBSERVE • IMPORTANT- Sa,'etheseinstructionsfl,r FOLLOWING: local inspector's use. A. Use this refit only in the rammer intended bv the •...
  • Page 3 Design Information CONTENTS Design Information Product Dimensions ............Step 2, Remove Packaging ..........Duct Cover Accessories ............ Step 3, Check Installation Hardware ....... Product Clearances ............Step 4, Mount Template ........... Advance PImming Step 5, Install Support Frame .......... Step 6, Secm'e Wiring ............. Tools and Materials Required...
  • Page 4 Advance Planning TOOLS AND MATERIALS REQUIRED POWER SUPPLY (not supplied) IMPORTANT - (Please read carefully) • Tapemeasure WARNING:, oR ,T.IS • Knife • Spirit level APPI_I_"4 CE MUST BE PROPERI N GROUNDED. • Wire cutter ATrENTION- • Wire stripper • Wire nuts SECURITE, CET APPAREIL DOlT ETRE...
  • Page 5 24 It. *Actual length of straight duct plus duct fitting equivalent. Equivalent length of duct pieces are based Total Duct on actual tests conducted by GE Evaluation Engineer- ing and reflect requirements for good venting performance with any ventilation hood.
  • Page 6 Installation Instructions [STEP 1]ADVANCE PLANNING Ceiling Plan location [Hood Determine exact location of the vent hood. i_Ducting • Use a plumb to check location to be sure countertop/cooktop location below hood will align exactly, • The hood should project tin'ward l-I/2"...
  • Page 7 Installation Instructions [STEP 11CONTINUED 2x 4 Min. CrossFraming • Arrange cross fl'aming in the ceiling to suit the existing structure. See examples. - Secure each 2 x 4 block with at least four (4), #10 wood screws, 3" hmg (not supplied). Use 8 wood screws total for the two supports.
  • Page 8 Installation Instructions ISTEP21 REMOVE THE PACKAGING vent hood is packed separate fl'mn the decorative duct cover or accessory co','ers ZX 1059SFSS ZX10510SFSS. • Remove the ti'ame, covei, parts box and packaging. • Remove junction box cover. • Install strain relief onto junction box cover.
  • Page 9 Installation Instruction [STEP 4] MOUNT TEMPLATE • Align the template with the marks on the ceiling and tape in place. - Be sure the template is oriented correctly, with the flxmt of the hood. • Use a plumb to check to be sure the mounting holes will provide parallel aligmnent...
  • Page 10 Installation Instructions ISTEP 71 ISTEP 61 SECURE WIRING SIZE AND INSTALL DUCTWORK • Route house wiring through the ceiling hole and pull a length to reach the hood junction box, approximately 6" below the support. fy,ing View Re red Side Support View Duct...
  • Page 11 Installation Instructions I STEP 81 INSTALL DECORATIVE DUCT COVERS Install Screwon EachSide Pretap Bottom Duct Cover 2 Screw Bottom Duct Holes_ (One Each Side) Install Stop Screw in Hole of Upper (Inner) Duct Cover • Slide the lower decorative duct over the installed •...
  • Page 12 Installation Instructions ISTEP101 CONNECT ELECTRICAL I STEP 111 SLIDE DUCT COVER DOWN Verify that power is turned off at the source. WARNING:. ,,.,,se,, iri, g i s n.t>,ire ,,,, a grotmd wire, a grotmd must be provided bv the hstaH installer.
  • Page 13 Installation Instructions ISTEP 121 INSTALL FILTERS, FINALIZE INSTALLATION Filter Slots • Remove protective fihn on the filters. • Tip rear of the filter into lower slots at the tin'ward opening. Liti filter pull knob until filter rests on the slots. •...
  • Page 14 Notes...
  • Page 15 Notes...
  • Page 16 Note: While performing installations described in this book, safety glasses or goggles should be worn. k)Jr Mo_og'r_m _ lo_d _vice i_ )our _lre_, c_ll 1-800-444-1845. Note: Product improvement is a COlltilluing endeavor (;eneral Electric. Theref_)re, materials, appearaJlce specifications arc" subject to change without notice.