GE Monogram ZV750 Installation Instructions Manual page 4

Design Information
36" Vent Hood
Advance
Plannin
Using Duct Cover Accessories
• A duct cover accesso_ y may be required for
your hood installation height. Refer to this
chart to determine the need for the ZX10SY
accessoiy.
ZV750SYDuct CoverDimensions
Hood and
Accessory A B
ZX750SY 18-7/8" 22-13/16"
ZX10SY - 34-1/4"
9-!!
11-7/8"
/4" ,
Ductwork
• Determine the exact location of the vent hood.
• Plan the route for venting exhaust to the
outdoors.
• Use the shortest and straightest duct route
possible. For satisfactory performance, duct run
should not exceed 100 feet equivalent length for
any duct configurations.
• Refer to "Duct Fittings" chart to compute the
maximum permissable length for duct runs to the
outdoors.
• Install a wall cap with damper or roof cap at the
exterior opening.
ZV750SYInstallationHeights
Actual
Ceiling * PossibleHood
Heitlht InstallationHeight
7' 11" 24-1/2"
8'O" 25-I/2"
8'1" 25-1/2" to26-1/2"
8'2" 25-1/2" to27-1/2"
8' 3" 25-1/2" to28-1/2"
8' 4" 25-1/2" to29-1/2"
8'5" 25-1/2"to 30"
8'6" 25-1/2"to 30"
8' 7" 25-I/2" to30"
8'8" 25-1/2"to 30"
8'9" 25-1/2"to 30"
8' 10" 25-1/2" to30"
8' 11" 25-I/2" to 30"
9' O" 25-1/2" to 30"
9' 1" 25-1/2" to 30"
9' 2" 25-1/2" to 30"
9' 3" 25-1/2" to 30"
9' 4" 25-1/2" to 30"
9' 5" 25-1/2" to 30"
9' 6" 25-1/2" to 30"
9' 7" 25-1/2" to 30"
9' 8" 25-1/2" to 30"
9' 9" 25-1/2" to 30"
9' 10" 25-1/2" to 30"
9' 11" 25-1/2" to 30"
10'0" 25-1/2"to30"
Duct Cover
t_
LU
...J
CL
CL
03
>-
O3
0
X
N
>-
fr-
o
Q3
Q3
LU
rj
¢,3
<
* Based on 36" countertop height.
Electrical
Supply
Warning, for
Personal Safety:
Remove house time or open
circuit breaker before beginning
installation.
Do not use an extension cord or adapter
plug with this appliance. Follow National
Elecuical Code or prevailing local codes
and ordinances.
• Gonnect the wiring to the house wiring in
accordance with local codes.
Grounding Instruction
The giounding conductor must be connected to
a ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the
hood.
Electrical supply
This vent hood must be supplied with 120V,
60Hz., and connected to an individual, properly
grounded branch circuit, protected by a 15 or 20
ampere circuit breaker or time delay fllse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the
above requirements, call a licensed elecuician
before proceeding.
• Route wiring as close to the installation
location as possible, in the ceiling or soffit.
Warning: The improper
connection of the equipment-
grounding conductor can result in
a risk of electric shock. Check with
a qualified electrician or service
representative if you are in doubt whether
the appliance is properly grounded.