Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kodak i7300
Summary of Contents for Kodak i7300
- Page 1 Scanner User’s Guide A-61404 Part No. 3E9366...
- Page 2 Safety and Installation Information for the Kodak i7300 Scanner / Kodak Digital Science Intelligent Microimage Scanner IMPORTANT: Equipment shall be installed by qualified personnel. CAUTION: Hot surface, avoid contact. CAUTION: Moving parts, avoid contact. User Precautions Users and their employer need to observe the common sense precautions applicable to the operation of any machinery.
-
Page 3: Acoustic Noise
NOTE: All data measured in accordance with DIN 45 635, ANSI S12.10-1985, and ISO 7779 in a hemi- anechoic chamber. Safety, Regulatory Conformance and Certifications The Kodak i7300 Scanner conforms to all applicable national and international product safety and electronic emission regulatory requirements. This includes, but is not limited to, the following: UL 60950, 3rd Edition CAN / CSA, C22.2 No. -
Page 4: Getting Technical Support
Getting Technical Support If you experience problems with your system, contact the Integrator or Kodak Response Center: Within New York State: 1-800-462-6494 Outside New York State: 1-800-822-1414 Alaska and Hawaii: 1-800-466-1414 For other countries, contact your local Kodak Service Support Center. -
Page 5: Table Of Contents
Table of Contents 1 Introduction ................2 Features ..................2 System requirements..............3 Product overview................4 2 Using the Scanner..............5 Turning on/off the power ..............5 Inserting a film magazine .............5 Unloading a magazine..............6 3 Maintenance ................8 Replacing the projection lamp............8 Supplies..................9 4 Troubleshooting ................10 Error messages ................10 Problem solving chart ..............15 Clearing a film jam or break ............15... -
Page 6: Introduction
Scanner and the Kodak Digital Science Intelligent Microimage Scanner. For the purpose of this manual, the term scanner will be used when referring to the Kodak i7300 Scanner and/or the Kodak Digital Science Intelligent Microimage Scanner unless otherwise noted. -
Page 7: System Requirements
Following are the minimum software and hardware requirements to run System the scanner. Hardware and software components are supplied by the requirements customer unless otherwise noted. * Supplied from Kodak (when purchased as separate products) CAR Mainframe Image Interface E-mail via... -
Page 8: Product Overview
Product overview The following illustration and descriptions will help you become familiar with the components of the scanner. The Manual Release Lever allows you to manually release the magazine by inserting a thin object, such as a pencil, into the slot. This lever should be used if a film jam or film breakage occurs. -
Page 9: Using The Scanner
Using the Scanner This chapter provides: Instructions for turning the power on and off. How to insert a film magazine. Instructions for loading and unloading film. Before you begin make sure the PC and the scanner are connected and power is applied to both devices. Turning on/off the The scanner can be powered on and off by using the toggle switch located in the back of the scanner (next to the scanner power cord). -
Page 10: Unloading A Magazine
Unloading a To unload a film magazine from the scanner: magazine 1. Select Refile on the Image Retrieval keypad of the Kodak i7300 Scanner Application Software or Navigate>Refile Film from the menu. The film will be rewound. A-61404 February 2003... - Page 11 IMPORTANT: If the Kodak i7300 Scanner Application Software is not running, use the Manual Release Lever on the front of the scanner and pull the film out or power down the scanner, wait 5 seconds, and power up the scanner.
-
Page 12: Maintenance
Maintenance Replacing the When the projection lamp burns out, replace the projection lamp as follows: projection lamp WARNING: If the scanner has been in use, the lamp assembly will be HOT. Allow the lamp area to cool a minimum of 5 minutes before attempting to change the lamp. -
Page 13: Supplies
9. Turn on the scanner. 10. Calibrate the scanner. Supplies The following supplies are available. Order them in the United States by calling Kodak Supply at 1-888-247-1234 or contact your local Kodak Reseller. Outside of the United States, contact your local Kodak dealer. Description Order No. -
Page 14: Troubleshooting
To correct an error condition, refer to the Corrective Action listed below. If the error condition is not corrected, contact your System Administrator. If the problem persists, call Kodak Service. Error Error message Possible Cause... - Page 15 Error Error message Possible Cause Corrective Action E206 The software has detected The film has jammed. Remove the film from the film path. a stalled motor. E207 The film refile was not Remove film from the film path by completed within the selecting Navigate>Refile Film or allowed amount of time.
- Page 16 Error Error message Possible Cause Corrective Action E217 A film motor error has been There is tension loss, abnormal Check the film path and remove any film detected. friction, or other similar transport debris. Remove the magazine and problems with the film. confirm that the film trail end holder is not protruding from the reel.
- Page 17 Error Error message Possible Cause Corrective Action E243 Random Batch Code error An error occurred while the scanner was attempting to read film containing Random Batch Code. The machine setup is Check the film. incorrect. There is a problem with the If problem persists, call service.
- Page 18 Additional error codes: Error Message Corrective Action 4000 Problem with host software – call for Click OK and try again. service. 4001 Internal timeout error: calibrating. The scanner is currently being calibrated. When calibration is complete, continue with the desired function. 4002 Internal timeout error: searching.
-
Page 19: Problem Solving Chart
Problem solving Use the chart below as a guide to check possible solutions to problems you may encounter when using the scanner. chart Problem Possible Solutions The 3 front LEDs on the Reset the circuit breaker on the back of the scanner. If the problem persists, scanner are on and will not go call service. - Page 20 Insert the heavier film (or film leader) into the film slot and manually feed the film through the film track. You will see it pass through the scan tower area. 7. Pull the loose end of the film being recovered off of the take-up reel and cut off the damaged, curled or bent end of the film, as needed.
-
Page 21: Appendix A Microfilm Information
Reels — the solid flange microfilm reel used in the scanner must be housed in one of the following: Kodak Ektamate Magazine Kodak Ektamate A Magazine ANSI Standard Magazine (open and enclosed designs) M-type Magazine A-61404 February 2003... -
Page 22: Image Mark Sizes
This reel should be installed in the magazine so the film feeds from the top, and the magazine’s threading symbol is on the same side as the reel’s square hole. NOTE: The scanner does not support the use of black camera spools or open flange reels. -
Page 23: Loading Film
Loading film The scanner is designed to offer optimum performance with ANSI magazines (Kodak Ektamate Magazines, or equivalent, and Kodak Ektamate A Magazines). In addition, the scanner accepts M-type magazines and enclosed ANSI magazines. Enclosed ANSI magazines may experience reduced threading performance when compared with “open”... -
Page 24: Enclosed Ansi Magazines
IMPORTANT: Enclosed ANSI magazines must be used with solid Enclosed ANSI flange reels designed specifically to fit with these magazines magazines. Standard ANSI film reels designed for open ANSI magazines may cause film transport performance problems when used in an enclosed magazine. To insert the reel into the magazine: Locate the release catch on the magazine (see the illustration) and release it by pressing with a small pointed object (such as a ball... -
Page 25: M-Type Magazines
CAUTION: Core fillers should not be used and existing fillers should be removed from reels. Damage could occur to your film and/or the scanner if core fillers are used. Reels used with the scanner should be Kodak Solid Flange Reels (or M-Film and reel checks equivalent). -
Page 26: Film Leader - Ansi Magazines
Make sure that the reel is not overfilled, as follows: If you are using a Kodak Solid Flange Reel, make sure that the film (when fully rewound) is not above the arrows on the reel’s side. -
Page 27: Film Trailer - Ansi Magazines
When using an ANSI magazine, use a trailer end holder to fix the film Film trailer — ANSI end to the supply reel. The following criteria should also be met. magazines Be sure to wind the film onto the supply reel in the correct direction. The film trailer must contain no images and must be at least 18 in. -
Page 28: Film Splicing
Use the following guidelines when splicing film: Film splicing For M-type magazines, the section connecting the leader tape and film should be at least 0.826 in. (21 mm) long. Leader Tape Film 0.826 in (21 mm) or longer The gap between the leader tape and film should be no more than 0.009 in. -
Page 29: Film Curl
For most film types and operating conditions, a certain amount of film Film curl curl can exist without adversely affecting the performance of the scanner (see the next section entitled, “Microfilm curl check”). Under certain conditions, however, curled film ends may result in degraded threading performance. - Page 30 Film Curl Ektamate Cartridge A-61404 February 2003...
- Page 31 Film Curl M Cartridge Curl should be less than 70 when toward roll; less than 40 when away from roll Away Toward A-61404 February 2003...
-
Page 32: Film Twist
Besides curl, the film should also be checked for twist. To make sure Film twist that the film’s twist is within allowable limits: Film twist 90° maximum (either direction) Allow about 12 in. (305 mm) of film to hang down from the reel. If the film twists more than 90°... -
Page 33: Film Magazine Condition
The condition of the film magazine is another factor affecting optimum Film magazine condition performance of the scanner. Film magazine conditions should meet the following criteria: The film magazine must not be distorted in shape (either closed downward or stretched outward). The film magazine's internal walls should be free of nicks, burrs, or other surface defects that lead to reduced threading and other problems. -
Page 34: Microfilm Storage
Microfilm should always be handled and stored with care. Storage of Microfilm storage your film should be based on the following: How long you want to keep the images on the microfilm: short, medium, long term, or permanently. How difficult the images are to replace. The cost of preserving the microfilm. - Page 35 EASTMAN KODAK COMPANY Document Imaging Rochester, New York 14650 Kodak, Digital Science and Ektamate, are trademarks of Eastman Kodak Company. Printed on recycled paper. DOCUMENT A-61404 2/2003 IMAGING CAT No. 120 8206 ©Eastman Kodak Company, 2003 Printed in U.S.A.