Page 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
Page 5
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories. G7297 Disc Sander 15. USE RECOMMENDED ACCESSORIES. 16. REDUCE THE RISK OF UNINTENTION- 17. CHECK DAMAGED PARTS. Before fur-...
STABILITY or integrity of the material to be sanded, do not sand it. Like all power tools, there is danger asso- ciated with the Model G7297 12" Disc Sander. Accidents are frequently caused by lack of familiarity or failure to pay atten- tion.
We are proud to offer the Model G7297 Disc Sander. This 12" disc sander is a part of a grow- ing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble- free, enjoyable operation and proof of Grizzly’s...
SECTION 3: CIRCUIT REQUIREMENTS 110 Volt Operation Amperage Draw The Model G7297 Disc Sander motor is wired to operate at 110V and will draw the following load: Motor Load...10 Amps Plug Type The Model G7297 Disc Sander is supplied with a NEMA 5-15 plug.
NOTICE The wire on the power cord with green or green and yellow striped insulation is the grounding conductor. G7297 Disc Sander Extension Cords 110V Operation If you find it necessary to use an extension cord at 110V: •...
SECTION 4: IDENTIFICATION The following is a list of controls and components on the Model G7297 Disc Sander. Please take time to become familiar with each item and its location. These items will be used throughout the manual and know- ing them is essential to understanding the instructions and terminology used in this manual.
If you need assistance determining whether you need to file a freight claim, or with the procedure to file one, please contact our Customer Service. The Model G7297 Disc Sander weighs 66 lbs. Personal injury could occur if the machine is moved without addition- al assistance.
Site Considerations Weight Load The Model G7297 Disc Sander is a small weight load with a small footprint. Most shop floors and workbenches should be sufficient to carry the weight of the machine. Reinforce the floor and workbench if you question its ability to support the weight.
Examine the edges of all metal parts before handling. G7297 Disc Sander When the table tilt is set to 0˚, the table should be adjusted perpendicular to the sanding disc face. To adjust table tilt:...
Figure 4. Squaring miter gauge to disc. -12- Attaching Sandpaper The Model G7297 Disc Sander accepts 12" diam- eter cloth or paper-backed PSA sanding discs. These are available in a variety of grits. See the current Grizzly catalog for prices and ordering information.
(Figure 6), and then press this portion against the disc. Figure 6. Removing protective layer. G7297 Disc Sander Aligning Table The table must be aligned to the face of the sand- ing disc so that the sandpaper does not rub against the table.
Disc Sanding Set the angle of the table relative to the sanding disc. The angle can be set with the angle gauge on the disc sander or with a pro- tractor for greater accuracy. When a 90˚ horizontal angle is required,...
(Figure 9). Rotation Figure 9. Mitering with gauge angled. G7297 Disc Sander Angle Sanding To perform angle sanding operations: Loosen the handles securing the table. Use the angle gauge to acheive the desired table angle and tighten the handles.
• Wipe off the sawdust build-up from the table surface. Weekly • Wipe a lubricant such as SLIPIT the table. Long-Term Storage • Keep unpainted surfaces rust free with products such as Boeshield G7297 Disc Sander ® onto ® T-9.
SECTION 9: REFERENCE INFO General This section contains the following subsections for the Model G7297 Disc Sander: aftermarket accessories, data sheets, wiring diagrams, parts diagrams list, troubleshooting, warranty/return information. If you need parts or help in assembling your machine, or if you need operational information, call the service department at (570) 546-9663.
Reduce load on motor, feed workpiece slower Clean out motor to provide normal air circulation. Inspect connections on motor for loose or shorted terminals. Correct the low voltage conditions. Install correct fuses or circuit breakers. Adjust table tilt. Adjust miter gauge. G7297 Disc Sander...
Warranty and Returns Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 25
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________...
Page 26
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
Page 27
Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why • • • – Trusted, Proven and a Great Value! ® Grizzly Is The Industry Leader! ® SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS E-MAIL RESPONSE WITHIN ONE HOUR...