Table of Contents
Advertisement
Quick Links
34º ANGLE FINISH NAILER - 2½"
MODEL H6144
INSTRUCTION MANUAL
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL6904 PRINTED IN CHINA
Advertisement
Table of Contents
Related Manuals for Grizzly H6144
Summary of Contents for Grizzly H6144
-
Page 1: Instruction Manual
34º ANGLE FINISH NAILER - 2½" MODEL H6144 INSTRUCTION MANUAL COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. -
Page 2: Safety Instructions For Machinery
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. - Page 3 ACCESSORIES. Refer to the instruction manual for recom- mended accessories. The use of improper accessories may cause risk of injury. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed. H6144 34° Angle Finish Nailer–2½"...
-
Page 4: Additional Safety Instructions For Nailers
H6144 34° Angle Finish Nailer–2½" HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching. - Page 5 Always pay attention to the direction this nailer is pointed. Use this tool with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warning may result in serious personal injury. H6144 34° Angle Finish Nailer–2½"...
-
Page 6: Contact Info
Foreword We are proud to offer the Grizzly Model H6144 34º Angle Finish Nailer–2½". This model is part of a growing Grizzly family of fine pneumatic tools. When used accord- ing to the guidelines set forth in this man- ual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s... - Page 7 Unpacking Your Model H6144 left our warehouse in a carefully packed box. If you discover the nailer is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing mate- rials for possible inspection by the car- rier or its agent.
-
Page 8: Compressed Air System
Compressed Air System The Model H6144 is designed to be oper- ated at 60-100 PSI using clean, dry, regu- lated, compressed air. DO NOT exceed the maximum operating pressure for your model. Before using your new nailer, install a ⁄... -
Page 9: Safety Yoke
— If either of these conditions develop after you have used your nailer for a period of time, check the lubrication of these mechanisms. H6144 34° Angle Finish Nailer–2½"... - Page 10 ⁄ " Capacity: 40 Angle: 34° NOTICE: A number of manufacturers' nails may fit the Model H6144. However, for best performance, we recommend you use the following Grizzly nails: G6085-G6088, G9545, G6090, G3693- G3697. To load your nailer: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2.
-
Page 11: Adjusting Depth
Figure 5, in Adjusting Depth. Adjusting Depth The Model H6144 features a knurled adjustment knob (Figure 5) for setting the nail depth into the workpiece. Figure 5. Depth adjustment knob. -
Page 12: Clearing Jammed Nails
A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the dis- charge area on the Model H6144: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! Always disconnect air from nailer whenever clearing a jammed nail! 2. -
Page 13: Replacing Pistons/O-Rings
11. After the piston is inserted correctly, close the magazine. Replace the top cap assembly and tighten the four cap screws. 12. For more assistance, or to install a complete O-ring set, refer to Parts Breakdown, Page 14. H6144 34° Angle Finish Nailer–2½"... -
Page 14: Cleaning And Lubrication
H6144 34° Angle Finish Nailer–2½" Lubricating Special oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 9) before every use, or after two hours of continuous use. - Page 15 H6144 PARTS BREAKDOWN H6144 34° Angle Finish Nailer–2½"...
- Page 16 PH6144040 ROLL PIN 3 X 28 PH6144041 JOINT SEAT PH6144042 FIXED BLOCK PH6144043 JOINT BOLT PH6144044 COMPRESSION SPRING H6144 34° Angle Finish Nailer–2½" REF PART # DESCRIPTION PH6144045 STEEL BALL 2MM PH6144046 SAFETY SEAT PH6144047 DRIVE PIN PR39M EXT RETAINING RING 8MM...
-
Page 17: Troubleshooting
5. Nails are wrong angle. 1. Nail is jammed in maga- zine or discharge area. 2. Piston shaft is damaged. 3. Air pressure too low. H6144 34° Angle Finish Nailer–2½" ACTION 1. O-rings must be replaced & operation of safety yoke must be checked. -
Page 18: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. -
Page 19: Warranty Card
City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX ____________ Model # H6144 34°Angle Finish Nailer–2½" Serial#________________Order #____________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential. - Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...