Download
Share
Print this page
CyberPower RMCARD202 User Manual
  1. Manuals
  2. Brands
  3. CyberPower Manuals
  4. Network Card
  5. RMCARD202
  6. User manual

CyberPower RMCARD202 User Manual

Network management card
Hide thumbs Also See for RMCARD202:

Advertisement

Quick Links

See also: User Manual
User's Manual
Network Management Card
RMCARD202
Intelligent Network Management Card
allows a UPS system to be managed,
monitored, and configured
Version 1.0
E-K01-SNMP005-0

Advertisement

loading

Related Manuals for CyberPower RMCARD202

Summary of Contents for CyberPower RMCARD202

  • Page 1 User’s Manual Network Management Card RMCARD202 Intelligent Network Management Card allows a UPS system to be managed, monitored, and configured Version 1.0 E-K01-SNMP005-0...

  • Page 2: Table Of Contents

    CyberPower Network Management System TABLE OF CONTENTS Introduction………………………………………………………………………1 Installation Guide………………………………………………………………..3 Web Interface…………………………………………………………………... 8 Reset to Default Setting / Recover from a Lost Password…………………15 Firmware Upgrade…………………………………………………….………..16 Trouble Shooting…………………………………………………….………….17 Appendix……………………………………………………………..…………..18...

  • Page 3: Introduction

    INTRODUCTION Overview The CyberPower Network Management Card allows for remote monitoring and control of a UPS attached to a network. After installing the hardware and configuring an IP address, the user can access, monitor, and control the UPS from anywhere in the world! Simply use a web browser such as Internet Explorer or Firefox to access your UPS.
  • Page 4 CyberPower Network Management System Application: Unpacking Inspect the Network Management Card upon receipt. The package should contain the following: CyberPower Network Management Card. PowerPanel Business Edition CD with software and user manuals.

  • Page 5: Installation Guide

    2. Remove the two retaining screws from the expansion port cover and remove the cover. 3. Install the CyberPower Network Management Card into the expansion port. 4. Re-install and tighten the retaining screws. 5. Connect the Ethernet cable to the LAN port on the CyberPower Network Management Card. 6. Turn on the UPS.
  • Page 6 Method 1 : Using the CyberPower Power Device Network Utility Tool 1. Install the CyberPower Power Device Network Utility Tool from the included CD. It is located on the CD in the \tools\network folder. Double click the “Power Device Network Utility”...
  • Page 7 CyberPower Network Management System Power Device Network Utility Figure 1. The main window of the “ ” program. 4. Select the SNMP card you are setting up. Click on the Tools menu and select “Device Setup” or double click the SNMP card you want to configure.
  • Page 8 CyberPower Network Management System 8. If IP address is successfully set, you will see a message that the IP set up is OK, as shown in Figure 4. Figure 4. Setup IP Address successfully message.
  • Page 9 CyberPower Network Management System Method 2: Using a command prompt 1. Obtain the MAC address from the label on the Network Management Card rear panel. Each Management card has a unique MAC address. 2. Use the ARP command to set the IP address.

  • Page 10: Web Interface

    CyberPower Network Management System WEB INTERFACE Login Account There are two user account types. Administrator (default username : cyber ; default password : cyber) Viewer (default username : device ; default password : cyber) The Administrator can access and control all functions, including enable/disable of the Viewer account.
  • Page 11 CyberPower Network Management System [UPS->status] Displays basic information about the current UPS status, and the items that are auto refreshed. item Definition Line Voltage Current input voltage of the utility power. Output Voltage The output voltage of the UPS. Output Frequency The frequency of output power.
  • Page 12 CyberPower Network Management System [UPS->Master Switch] Switches the output power of the UPS to be on or off. Items Definition Reboot UPS Turns the UPS off and back on Turn UPS Off Turns the UPS off. Turning the UPS off and back on after a period of UPS Sleep time.
  • Page 13 Failed: The battery test resulted in failure. Follow the steps below if the battery test fails: Repeat the battery test and replace the batteries if the test fails again. Contact CyberPower for assistance if the battery test fails after the batteries have been replaced. Runtime Calibration The Runtime Calibration ensures the runtime estimate is accurate with the load and the current battery capacity.
  • Page 14 CyberPower Network Management System [Logs->Event Logs] Displays a list of events along with a date and time stamp, and a brief description of event. Note: The events recorded will be listed under “System->Event Action” [Logs->Status Records] This page is used to view the logs of the UPS status.
  • Page 15 [System->Trap Receivers] Set up to ten trap receivers in the IP format. The receiver will receive a SNMP trap when an event occurs. When the PowerPanel Business Edition Client connects to the CyberPower UPS, the IP address of the PowerPanel Business Edition Client will be added the list of Trap Receivers automatically.
  • Page 16 CyberPower Network Management System [System->Shutdown] Items Definition The Longest shutdown delay time required for Clients Shutdown Delay connected PowerPanel Business Edition Client. Select to renegotiate the Clients Shutdown Delay with connected PowerPanel Business Edition Client .The Force Negotiation Clients Shutdown Delay will return to a default of 2 minutes, and the negotiation time is up to 10 minutes to finish.

  • Page 17: Reset To Default Setting / Recover From A Lost Password

    Note: the MAC address is also listed on the top of the Network Management Card . Reset to Default Setting / Recover from a Lost Password To reset the CyberPower Network Management Card to its default setting (including WEB log-in user name and password), please use the following steps. RESET 1.

  • Page 18: Firmware Upgrade

    Download the latest Firmware. Extract the file to “C:\” Open a command prompt window Login to the CyberPower Network Management Card with FTP command, type ftp> open To [ip] [port] ; EX: To 192.168.22.126 21 Input USER NAME and PASSWORD (same as the administrator account in Web interface default : cyber ;...

  • Page 19: Trouble Shooting

    CyberPower Network Management System Trouble Shooting Problem Solution 1.Check the LED status, the normal condition is both yellow and green led is on. If green led is off: Check the Management Card for proper seating in Unable to configure the the UPS and the UPS power is on.

  • Page 20: Appendix

    The same address cannot be used twice. In order to assign an IP address to the CyberPower Network Management Card, you must determine the range of the available IP addresses, and then choose an unused IP address to assign to the Network Management Card.
  • Page 21 CyberPower Network Management System If the response is shown as below, the IP address is in use. Try another IP address until an available address is found. Pinging 192.168.20.240 with 32 bytes of data: Reply from 192.168.20.240: bytes=32 time<10ms TTL=64 Reply from 192.168.20.240: bytes=32 time<10ms TTL=64...