Grizzly G8691 Instruction Manual

Wood lathe with stand.
Hide thumbs
WOOD LATHE WITH STAND
MODEL G8691
INSTRUCTION MANUAL
COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
FEBRUARY, 2001. PRINTED IN CHINA.

Advertising

   Also See for Grizzly G8691

   Related Manuals for Grizzly G8691

   Summary of Contents for Grizzly G8691

  • Page 1

    WOOD LATHE WITH STAND MODEL G8691 INSTRUCTION MANUAL COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. FEBRUARY, 2001. PRINTED IN CHINA.

  • Page 2: Table Of Contents

    1. SAFETY WARNINGS ...2 SAFETY RULES FOR ALL TOOLS ...3 ADDITIONAL SAFETY INSTRUCTIONS FOR G8691 ...4 2. CIRCUIT REQUIREMENTS 110V OPERATION ...5 GROUNDING ...5 EXTENSION CORDS ...5 3. INTRODUCTION COMMENTARY ...6 UNPACKING ...7 PIECE INVENTORY ...7 CLEAN UP...8 SITE CONSIDERATIONS ...8 4.

  • Page 3: Safety Instructions For Power Tools

    G8691 Wood Lathe w/ Stand VISITORS...

  • Page 4

    15. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury. G8691 Wood Lathe w/ Stand 16. REDUCE THE RISK OF UNINTENTION- 17. MANY WOODWORKING TOOLS CAN LENGTH 50ft 100ft 18.

  • Page 5: Additional Safety Instructions For The Lathe

    Make sure you know what type of wood dust you will be exposed to, the possibility of a allergic reaction and always wear an approved respirator. G8691 Wood Lathe w/ Stand...

  • Page 6: Circuit Requirements 110v Operation, Grounding, Extension Cords

    Extension Cords If you find it necessary to use an extension cord with the Model G8691, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instructions to determine the minimum gauge for the extension cord.

  • Page 7: Introduction Commentary

    SECTION 3: INTRODUCTION Commentary We are proud to offer the Grizzly Model G8691 Wood Lathe w/ Stand. The Model G8691 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satis-...

  • Page 8: Unpacking, Piece Inventory

    Customer Service. When you are completely satisfied with the condi- tion of your shipment, you should inventory its parts. G8691 Wood Lathe w/ Stand Piece Inventory After all the parts have been removed from the carton, you should have: • Lathe Assembly •...

  • Page 9: Clean Up, Site Considerations

    Clean Up Grease left over from the manufacturing process may be on the various parts of the lathe. It is rec- ommended to clean this grease off with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact.

  • Page 10: Assembly Beginning Assembly, Stand, Tool Rest

    SECTION 4: ASSEMBLY Beginning Assembly Most of your Model G8691 Wood Lathe has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps. Please follow along in the order presented here.

  • Page 11: Tailstock, Spur Center, Faceplate

    Serious personal injury could occur if care is not taken. Spur Center The Model G8691 is supplied with a #2 Morse Taper spur center for use when spindle turning. The spur center is used in conjunction with the tailstock live center.

  • Page 12: Operations Test Run, Spindle Turning

    Be certain the safety glass- es you wear meet the appropriate stan- dards of the American National Standards Institute (ANSI). G8691 Wood Lathe w/ Stand Spindle Turning To mount a workpiece between centers: Locate the center point on both ends of the workpiece by carefully drawing diagonal lines from corner to corner.

  • Page 13: Speed Selector, Tool Rest

    Failure to observe this step could result in the workpiece being thrown from the lathe. Serious personal injury could occur if care is not taken. G8691 Wood Lathe w/ Stand...

  • Page 14: Maintenance General, Lubrication, V-belt

    SECTION 6: MAINTENANCE General Regular periodic maintenance on your Model G8691 Wood Lathe will ensure its optimum per- formance. Make a habit of inspecting your lathe each time you use it. Check for the following con- ditions and repair or replace when necessary: 1.

  • Page 15: Closure

    -14- We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department listed in Section 3: Introduction.

  • Page 16: Machine Data

    Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G8691 WOOD LATHE WITH STAND Design Type ...Floor Model Overall Dimensions: Including Stand ...42" H x 17" W x 54 Shipping Weight ...76 lbs.

  • Page 17

    -16- G8691 Wood Lathe w/ Stand...

  • Page 18

    Washer M12 P8691046 Tailstock Tension Plate P8691047 Turning Knob P8691048 P8691049 Speed Switch G8992 Switch P8691051 Fuse G8691 Wood Lathe w/ Stand Ref# Part# Description P8691052 Phillips® Hd Scr M6 x 12 P8691053 Switch Label P8691054 Switch Faceplate P8691055 Bracket P8691056...

  • Page 19: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

  • Page 20: Warranty Card

    Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________...

  • Page 21

    FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...

Comments to this Manuals

Symbols: 0
Latest comments: