Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for Grizzly G8690
Summary of Contents for Grizzly G8690
- Page 1 VARIABLE SPEED WOOD LATHE MODEL G8690 INSTRUCTION MANUAL COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REPRINTED JUNE, 2001 PRINTED IN TAIWAN.
-
Page 3: Table Of Contents
1. SAFETY SAFETY RULES FOR ALL TOOLS ...2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR G8690 ...4 2. CIRCUIT REQUIREMENTS 110V OPERATION ...5 GROUNDING ...5 EXTENSION CORDS ...5 3. INTRODUCTION COMMENTARY...6 UNPACKING ...7 PIECE INVENTORY ...7 CLEAN UP...8 SITE CONSIDERATIONS ...8 4. ASSEMBLY BEGINNING ASSEMBLY ...9... -
Page 4: Safety
G8690 Variable Speed Wood Lathe VISITORS... - Page 5 15. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury. G8690 Variable Speed Wood Lathe 16. REDUCE THE RISK OF UNINTENTION- 17. MANY WOODWORKING TOOLS CAN LENGTH 50ft 100ft 18.
-
Page 6: Additional Safety Instructions For G8690
14. REMOVE THE TOOL REST when perform- ing sanding or polishing operations on the rotating spindle. PROPERLY 15. ATTEMPTING TO REMOVE too much material at once may cause work material to fly out of the lathe. G8690 Variable Speed Wood Lathe... -
Page 7: Circuit Requirements
3.5 amps. Extension Cords If you find it necessary to use an extension cord with the Model G8690, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instructions to determine the minimum gauge for the extension cord. -
Page 8: Introduction
Grizzly’s commitment to customer satis- faction. The Model G8690 is a wood turning lathe with a variable spindle speed range of zero to 3025 R.P.M. Capacity between the centers is adjustable up to 19" and the swing over the bed is 6". -
Page 9: Unpacking
NOTICE Save all containers and packing materials until you are satisfied that your Model G8690 has arrived in good condition. Freight company adjusters will want to inspect those materials in the event that a freight claim must be made. -
Page 10: Clean Up
Your Model G8690 represents a moderately large weight load in a small footprint. Ensure that your workbench is sturdy enough to carry the weight of the Model G8690. If you question the strength of your workbench, you can opt to reinforce it. WORKING CLEARANCES... -
Page 11: Assembly
Failure to comply may result in serious personal injury. Most of your Model G8690 has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps. Please follow along in the order presented here. -
Page 12: Tool Rest
Figure 5. Tailstock mounted to guide rails. Live Center The live center is installed by inserting the end of the shaft into the tailstock assembly. While hold- ing in place, turn the handwheel on the tailstock clockwise until snug. G8690 Variable Speed Wood Lathe... -
Page 13: Spur Center
Spur Center The Model G8690 is supplied with a #1 Morse Taper spur center for use when spindle turning. The spur center is used in conjunction with the tailstock live center. Install the spur center by inserting it into the hole in the headstock spindle end. -
Page 14: Operations
See Figure 6B. Wood with splits along the grain may fly off during the operation. With dense wood, drill a hole at the centers and score lines with a saw blade for the spur. G8690 Variable Speed Wood Lathe... -
Page 15: Speed Selector
Use good judgement. Serious personal injury could result if care is not taken. G8690 Variable Speed Wood Lathe Speed Selector The variable speed selector allows the adjust- ment of the spindle R.P.M. Before turning the lathe on, make sure the speed selector knob is set at the lowest R.P.M. -
Page 16: Tool Rest
See Figure 8. Figure 8. Correct hand placement for operation. Wear a face shield dur- ing the test run and operation of this wood working lathe. Failure to do so could result in serious injury. -14- G8690 Variable Speed Wood Lathe... -
Page 17: Maintenance
2. Worn switch. 3. Worn or damaged cords and plugs. 4. Damaged cog tooth belt. The non-painted surfaces on the Model G8690 should be protected against rust and pitting. Wiping the lathe clean after every use ensures that wood dust isn’t allowed to trap moisture against bare metal surfaces. -
Page 18: Closure
-16- We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or replacement parts, please contact the Service Department listed in Section 3 Introduction. -
Page 19: Machine Data
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G8690 VARIABLE SPEED WOOD LATHE Design Type...Bench Top Model Overall Dimensions: ...9 Base to Center Height ...6 Swing Over Bed...6" Distance Between Centers ...19"... - Page 21 SETSCREW M6-1 X 8 P8690041 TOOL REST P8690042 DBL END SCR M12-1.75-65 P8690043 KNOB PSS02M SETSCREW M 6-1 X 8 P8690045 GUIDE BAR G8690 Variable Speed Wood Lathe Ref# Part# Description PSS01M SETSCREW M6-1 X 10 P8690047 FOOT P8690048 COVER PSS01M...
-
Page 22: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. -
Page 23: Warranty Card
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________... - Page 24 FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here...