Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly 1008
Summary of Contents for Grizzly 1008
- Page 1 VERTICAL MILLING MACHINE MODEL G1004/G1008 INSTRUCTION MANUAL COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED OCTOBER, 1999. PRINTED IN U.S.A.
-
Page 2: Table Of Contents
5. OPERATIONS SPEED CHANGES ...13 TEST RUN...13 6. ADJUSTMENTS GRADUATED DIALS...14 SPINDLE HEIGHT...14 DEPTH STOP ...14 7. MAINTENANCE GENERAL ...15 BEARINGS ...15 LUBRICATION...15 GIBS ...15 8. CLOSURE COMMENTARY...16 WARRANTY AND RETURNS ...17 G1004/1008 Vertical Milling Machine Table Of Contents PAGE... -
Page 3: Safety
G1004/1008 Vertical Milling Machine VISITORS... - Page 4 12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool. G1004/1008 Vertical Milling Machine 13. DON’T OVERREACH. Keep proper foot- 14. MAINTAIN TOOLS WITH CARE. Keep 15. DISCONNECT TOOLS before servicing 16.
-
Page 5: Additional Safety For Milling Machines
Use this tool with respect and caution to lessen the possibility of operator injury. If normal safety precautions are over- looked or ignored, serious personal injury Standards may occur. G1004/1008 Vertical Milling Machine... -
Page 6: Circuit Requirements
20 amp fuse or circuit breaker. This should be satisfactory for normal use, while providing enough protection against motor damage caused by power surges. Grizzly recommends that the circuit you use should be dedicated, (i.e., the G1004 or G1008 should pro- vide the only draw from that circuit). -
Page 7: 220 Volt Operation
15 amp fuse or circuit breaker. This should be satisfactory for normal use, while providing enough protection against motor damage caused by power surges. Grizzly recommends that the circuit you use should be dedicated, (i.e., the G1004 or G1008 should pro- vide the only draw from that circuit). -
Page 8: Introduction
SECTION 3: INTRODUCTION Commentary Grizzly Industrial, Inc. is proud to offer the Model G1004/G1008 Milling Machine. These Milling Machines are a part of Grizzly’s growing family of fine metalworking machinery. When used accord- ing to the guidelines stated in this manual, you can expect years of trouble-free, enjoyable oper- ation. -
Page 9: Unpacking
NOTICE A full parts list and breakdown can be found toward the end of this manual. For easier assembly, or to identify missing parts, please refer to the detailed illustrations. G1004/1008 Vertical Milling Machine... -
Page 10: Clean Up
Please examine the edges of all die-cut metal parts and file or sand the edge to remove the flashing before handling. G1004/1008 Vertical Milling Machine Site Considerations FLOOR LOAD Your G1004/G1008 Milling Machine represents a large weight load in a 28"... -
Page 11: Assembly
Should you find that the machine rocks or is not level, use mild steel shim stock or leveling pads, such as those sold by Grizzly Industrial (G7159). -11-... -
Page 12: Fly Cutter
Remove cutting tools from spindle when not in use. G1004/1008 Vertical Milling Machine Fly Cutter Your mill comes equipped with a fly cutter that fits on the 1" stub end of the R-8 arbor (this comes installed in the spindle). -
Page 13: Operations
Strange or unnatural noises should be investigated and corrected before operating the machine further. If noises occur that can not be found by visual inspection, feel free to contact our service depart- ment for help. BELT POSITIONING CHART Test Run G1004/1008 Vertical Milling Machine... -
Page 14: Adjustments
The handwheel will not function if the knurled locking knob is loose. G1004/1008 Vertical Milling Machine 3. Loosen the setscrew on the knurled surface of the handwheel dial. Turn the dial until the “0” lines up with the index line. Tighten the setscrew. -
Page 15: Maintenance
SAE 20 using an oil can with a pointed nozzle to help push in the ball. Gibs The G1004/1008 milling machine table features tapered gibs in the dovetail ways. To tighten the table, loosen the screw at the small end of the tapered gib and tighten the screw at the large end. -
Page 16: Closure
G1004/1008 Vertical Milling Machine We recommend you keep a copy of our current catalog for complete information regarding Grizzly's warranty and return policy. If you need additional technical information relating to this machine, or if you need general assistance or... -
Page 17: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.