Unit Features - Soleus Air SG-PTAC-09HPDA Owner's Manual

UNIT FEATURES

This Premium unit has many exciting features which
are different than those found on standard PTAC
models. The owner must be familiar with these
features in order to fully understand the operation and
capability of the unit.
• Intelligence – Your Premium unit has an on board
computer that utilizes real time diagnostics to prolong
the life of your unit. There is an LED indicator on the
control board, behind the front panel, that will flash
an error code if the unit has detected some kind of
fault condition. In many cases, the unit will
automatically clear the fault condition and continue
operating with no interruption. In some cases, the
condition cannot be cleared and the unit will require service. In those cases, an "Fx" failure mode will be
displayed on the digital display. For a detailed list of all error codes and "Fx" conditions, see Table 6 - -
Status LED Indicator Definitions for further details.
• Memory – Your Premium unit also has memory. If power is lost, all of the control settings (setpoint,
mode, fan speed, on/off and configuration) are remembered. So when power is restored, the unit will
start back up in the mode (and configuration) it was in, when power was lost.
• Premium Sound – The unit not only does it have2 fan motors and a tangential blower wheel for
optimum sound, the indoor fan will always run a minimum of 10 seconds before the compressor, to
help reduce any compressor starting noise.
• Random Compressor restart - - To help prevent power surges after a power outage (from many of
your PTACs starting at the same time), the compressor is equipped with a 2:45 to 3:15 random
restart delay feature. Whenever the unit is plugged in, or power has been restarted, a random compressor
restart will occur.
• Compressor Protection - - To prevent short cycling of the compressor and maximize it's life, there is a
random start- -up delay of 3 minutes on the compressor and a minimum compressor run time of 3 minutes.
• Automatic room freeze protection – automatically will keep the temperature in the room from getting
too cold, where water pipes might freeze. If the unit is configured for the freeze protection feature to be
active (which is the default condition), then whenever power is supplied to the unit, if the unit senses
temperature below 40°F, the fan motor and electric heater are turned on and will warm the room to 50_F.
If Freeze protection is not required, change the configuration switch to turn the feature off (see
section on unit configuration).
• Automatic defrost protection (for heat pump models only) – When the outdoor temperature gets
too cold (approx. 35°F) and the unit can no longer effectively heat with the compressor, the unit will
automatically switch to electric heating. The unit will then heat with electric heat until the outside
temperature rises enough (approx. 40°F), so the compressor can be used again.
• Automatic Quick Warm- -up (for heat pump models only) - - If the room temperature falls to 5°F
below the set point temperature, the reverse cycle heat is shut off and the electric strip heat is turned on
for one cycle, until heating is satisfied.
• LED Indicator's and Buttons - - The touch pad has buttons for MODE, FANSPEED, ON/OFF,
SETPOINT UP and SETPOINT DOWN. It also has LEDs that correspond to the mode, fan speed and
setpoint operation, to indicate the unit's status. The LEDs below the mode button, FAN, COOL, and
HEAT, indicate what operating mode is active. The LEDs below the Fan button, Low, Med and Hi,
indicate the fan speed that is selected. The LED located in the lower right corner is the unit On/Off
status LED. If the unit is in ON mode, the LED will be green. If the unit is OFF, the LED will be red.
• Configure Fan to Optimize Selected Application - - Unit can be optimized to selected application by
configuring the fan to run in continuous mode or cycle on and off with the compressor and electric
heater (can be different for both heating and cooling modes). In cycle mode, fan will continue to run after
compressor or electric heater stops in order blow off any residual heat or cool left on coil.
1 Indoor air temp sensor open/short
2 Indoor coil sensor open/short
3 Outdoor coil sensor open/short
4 Freeze Guard protection
5 Thermostat wiring error
6 Indoor coil high temp protection
7 Defrost (heat pump type)
8 Outdoor coil high temp protection
9 Indoor coil freeze protection
NOTE: When status light is flashing, it will be ON for 0.5 seconds and OFF for another 0.5 seconds.
Table 6—STATUS LED Indicator Definitions
7--- segment display 'F1', with STATUS light flash 1 time,off 2 seconds
7--- segment display 'F2', with STATUS light flash 2 time,off 2 seconds
7--- segment display 'F4', with STATUS light flash 4 time,off 2 seconds
7--- segment display 'FP'
STATUS light flash 9 times and off 3 sec, repeat
STATUS light flash 8 times and off 3 sec, repeat
STATUS light flash 7 times and off 3 sec, repeat
STATUS light flash 6 times and off 3 sec, repeat
STATUS light flash 5 times and off 3 sec, repeat
2
Fig. 2