Page 1
Operation manual for Airless paint sprayer High Pressure Electric Airless paint sprayer Titan 440i model intelligent series Remark: this guide manual is the same with model DP-6389 ,the content include :the operation of equipment,cleaning ,maintenance ,and repair,be sure to pre-operational ,read...
1. warning and precautions Safety Precautions This manual contains information that must be read and understood before using the airless sprayer equipment. When you come to an area that has one of the following symbols, pay particular attention and make certain to heed the safeguard. WARNING This symbol indicates a potential hazard that may cause serious injury or loss of life.
Page 3
NOTE TO PHYSICIAN: Injection into the skin is a traumatic injury. It is important to treat the injury as soon as possible. DO NOT delay treatment to research toxicity. Toxicity is a concern with some coatings injected directly into the blood stream. Consultation with a plastic surgeon or reconstructive hand surgeon may be advisable.
Page 4
• Contact your coating supplier about the compatibility of material with aluminum. HAZARD: HAZARDOUS VAPORS – Paints, solvents, insecticides, and other materials can be harmful if inhaled or come in contact with body. Vapors can cause severe nausea, fainting, or poisoning. PREVENTION: •...
Page 5
Grounding Pin Cover for grounded outlet box CAUTION Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the product. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
Page 6
Pump filters The percolation gets into the coating in the equipment Return Valve return to vertical direction for the state open ,the horizontal direction for spraying state (close) Coating painting outlet Link Coating tube and manometer Position Will be from buckets in the paint inhalation equipment Suction tube Paint return tube Return to the state paint or solvent outflow from here...
operation I prepare before switching on. 1. prepare tool: 5-inch,6-inch all within a hexagonal wrench. Cross screw 4 iii. 14-17、17-19of a double-headed wrench a blender or a stirring rod antivirus mask and a set of overalls a brush vii. some rags viii.
Page 8
3. the initial use of new equipment: the new equipment of the factory contain a protective effect lubricants,so the initial use of new equipment need to join the clean water of few soap to take in to clean ,the flollowing step is cleaning: ⑴add to suction tube containing a little soapy water in the buckets ⑵add to the waste will be returned in the paint barrels\buckets.
Page 9
⑽open spray gun insurance . ⑾ paint gun mouth to discard the paint wall inside the bucket ,deduction under the trigger,and the spray gun to paint the original old solvent removed ,until the clean up of the new solvent exclusion .(as the above chart) ⑿close spray gun insurance(as the right chart)...
Page 10
3. pressure relief steps ! !warning! ! in any equipment cleaning ,repair and maintenance or before the middle of the break, and you must step in accordance with the venting pressure relief . ⑴ close spray gun insurance(as the right chart) ⑵shut the power switch.
Page 11
spraying skills 1. Caution should be taken when operating spray gun, high-pressure hoses and operator of physical coordination between the two, the operator standing at the feet spraying distance slightly over Shoulder Width, a high-pressure pipe in their hands, high-pressure pipe will be not stretched too tight, help to Spray when the shift easier.
Page 12
In order to obtain complete and uniform coating, we are here to advise you when the spray gun should be covered before each shot 50 percent, that is, 50 per cent of the lap, so the entire work surface coating line Uniform (as for chart).
Page 13
cleans ⑴ First according to the "pressure relief steps" to eject the pressure and coating inside equipment. ⑵ Nozzles and nozzle jacket will be unloaded. ⑶ Add suction pipe will be put into clear water bucket or the appropriation dilution. ⑷...
maintenance Before maintenance, you must determine the fault of the equipment, otherwise, the equipments unnecessary equipment ac cessibility will seriously affect the function and greatly reduce the service life of equipments . Also in the maintenance of the equipment, be sure to be dressed in overalls and maintenance tool standards, and adequate lighting and choose a well-ventilated place to carry out repairs and prepare a bucket of clean solvent, as well as the equipment at the various components within the washing.
Page 15
Return valve maintenance steps ⑴ Remove return valve switch on the bolt. ⑵ Unloading return valve switch and switch back seat. ⑶ By wrench return valve components unloaded thimble. ⑷ Determine return valve gaskets in the right position. ⑸ Will be a new return valve installed on components screwed tightly onto.
Page 16
● Suction ring component replacement ⑴ In accordance with the "ball valve maintenance steps" to unload the upper and lower ball valve. ⑵ Suction component will be below the two-position rotary nut removed. ⑶ Suction tube components will be slightly shelland pulled down so that the shell about 1.5 cm from the equipment.
⑿ In determining seals ring and locator installed in the correct position, the piston rod will be components from the suction casing from the bottom to bottom-up equipment, and rubber hammer to knock plunger rod gently into the suction components, until the plunger rod into the correct position.
Page 18
No suction equipment 1. air in the tube 1. Check suction tubes and open to return valves 2.Inadequate equipment pressure 2. increase pressure fluxing is too small or 1. No paint supply 1. Inspection no fluxing 2.Cleaning or replacement filters 2 Suction tube filter plug.
Page 19
spray gun not expecting 1 Supply free paint. 1. checking 2. nozzle Or filter plug 2. Cleaning spray gun and seal ring 3. spray needle wear 3. spray needle replacement 3. Spray Frequently asked questions Trailing spray sites 1.Spraying under pressure 1.
8、 exploded drawing and parts list Suction component decomposition map...
Page 22
Suction Component Model Description List quantity Product Description Quantity Product Description Suction components 1 Under Ball Valve Cylinder Complete suction components ( Does not include No.24-27) Filter gaskets Filters Plunger rod components Shell filters 3 Fixed nut Return valve components (...
Page 23
Annex 一 . Nozzle Selection Spraying the spray paint and the flow rate is determined by the nozzle, so choosing the right nozzle is very important and appropriate spraying construction sites can enhance the efficiency of the flow is appropriate to reduce unnecessary waste of paint, and vice versa Ran.Generally speaking, the viscosity of the coating in the choice of spray nozzle and the flow rate, an important subject, when used by the lower viscosity of the coating, we usually recommend the use of spray flow rate narrower and smaller nozzle Conversely, if coating...
Page 24
10. Technical data for DP6389 Electric power rating 900W Input voltage AC180—240V Output voltage DC200—220V frequency 50HZ Maximun output pressure 20MPa The largest unloading flow 2.1L/min The largest spray flow 1.9L/min Effective spray distance 350-400mm Spray width 250mm Compressive strength of the 30 MPa high pressure Max.nozzle type...
Page 25
Product Quality Guarantee 1. Ensure that the products are Dino-Power Industry & Trade Co., Ltd. original products. Ensure that the products are qualified products, such as a product is found to have quality problems itself, users have the right to request replacement of local authorized dealers similar qualified products.
Need help?
Do you have a question about the Titan 440i and is the answer not in the manual?
Questions and answers