Table of Contents
Advertisement
Quick Links
Do not use this equipment before reading this manual!
Airless Paint Sprayer
No 168 MingGuang Road, Yinzhou District, Ningbo, China
www.dpairless.com
International Model
Original instruction
DP6388B
NOTE: This manual contains important warnings and
instructions. Please read and retain for
reference
Ningbo Dino-power Machinery Co.,Ltd
or
www.airlesspaintsprayer-pump.com
Owner's Manual
For professional Use only
www.dino-power.com
Advertisement
Table of Contents
Related Manuals for Dino-Power DP6388B
Summary of Contents for Dino-Power DP6388B
- Page 1 Do not use this equipment before reading this manual! Airless Paint Sprayer International Model Original instruction DP6388B NOTE: This manual contains important warnings and instructions. Please read and retain for reference Ningbo Dino-power Machinery Co.,Ltd No 168 MingGuang Road, Yinzhou District, Ningbo, China www.dpairless.com www.airlesspaintsprayer-pump.com www.dino-power.com...
-
Page 2: Table Of Contents
Table of Contents The operating instructions state that the following points must always be observed before starting up: Safety Precautions............2 1.Faulty units should not be used. General Description............4 2.Secure spray gun using the safety catch on the trigger Technical Parameter............4 3.Ensure that the unit isproperly earthed. - Page 3 9. Attention! Please observe the following when working NOTE TO PHYS ICIAN: inside and outside: Injection in to the skin is a tr aumatic injury. It is No Solvent Gasses Should be carried to the unit. No important to theat the injury surgically as soon as solvent gasses should from near the unit.
-
Page 4: General Description
General Description Setup Perform the following procedure before plugging in the power This airless spraye r is a precision power tool used for spraying cord of an electric unit. many types of mate rials. R ead and follow this ins truction 1.Ensure that the suction set and the return hose are manual carefully for prope r operating instructions, and attached and secure. -
Page 5: Preparing To Paint
Preparing to Pain WARNING Before painting, it is important to make sure that the fluid in the system is compatible with the paint that is going to be used. Be sure to follow the pressure relief procedure when NOTE: Incompatible fluid and paint may cause the shutting the unit down for any purpose ,including valves to become stuck closed ,which would servicing or adjusting any part of the spray system,... -
Page 6: Pressure Relief Procedure
Pressure Relief Procedure Avoid arcing or holding the gun at an angle ,This will result in an uneven finish. WARNING Be sure to follow the pressure relief procedure when shutting the unit down for any purpose ,including Off spray servicing or adjusting any part of the spray system, changing or cleaning spray tips, or preparing for clean up. -
Page 7: Practice
PRACTICE 1.Be sure that the paint hose is free of kinds and clear of 7.Submerge suction tube in objects with sharp cutting edges. water or flushing solvent. 2.Turn the pressure control knob counterclockwise to its to its lowest setting. 3.Turn the PRIME/SPRAY valve up to its SPRAY position. 4.Turn the pressure control knob clockwise to its highest setting. -
Page 8: Troubleshooting
Troubleshooting Problem Cause Solution 1.Plug the unit in The unit will not run 1.The unit is not plugged in 2.Tripped breaker 2.Reset the breaker. 3.The pressure is set too low(pressure 3.Turn the pressure control knob control knob set at minimum setting clockwise t supply power to the unit does not supply power to unit) and increase the pressure setting. - Page 9 Troubleshooting Problem Cause Solution 1.Wrong type of airless spray hose. 1.Replace hose with a minimum of 5m Excessive surge at the 2.The Spray tip worn or too large. (50 ”)X10mm(1 /4”) ground textiled spray gun. 3.Excessive pressure. braid airless paint spray hose. 2.Replace the spray tip following the instructions that came with the spray gu 3.Rotate the pressure control knob...
-
Page 10: Parts Listings
10 . -
Page 11: Motor Assembly
Motor Assembly Motor Assembly 1.Motor..........1 9.ON/OFF switch........1 2.Screw........2 10.Screw..........4 3.Motor fan....... 1 11.Circuit breaker.........1 4.Screw........4 12.Pin............2 5.Gasket........1 13.Motor holder........1 6.Motor cover labels....1 14.Couper oring........1 7.Strain relief......1 15.Screw..........4 8.Power cord......1 16.Electric main board......1 11 . -
Page 12: Gear Box Assembly
Gear Box Assembly Gear Box Assembly 1.Cover laber ........1 8.Gear wrap........1 2.Screw ........... 8 9.Wrap..........1 3.Front cover w/label ......1 10.2nd stage gear......1 4.Rod ............1 11. Pin.............1 5.Rod couper o-ring ......1 12. Gear wrap........2 6.Pump housing ........1 13. Pin............ 2 7.Crankshaft/gear assembly ... -
Page 13: Fluid Section Assembly
Fluid Section Assembly Fluid Section Assembly 1.Fluid section ........1 11..............Rocl 1 2.Piston ..........1 12.Spring ..........1 3.Piston wrap A ........1 13.Coupler ..........1 4.O-ring ..........1 14.O-ring ..........1 5.Piston wrap B ......... 1 15.Cover ..........1 6.O-ring ..........1 16.O-ring ..........2 7.O-ring ..........1 17.Pressure rocl ........1 8.Lvasher .......... -
Page 14: Tip Selection
22. Coupler...........1 Choosing The Correct Tip 23. Spring..........1 Consider Coating and Surface to be Sprayed. Make sure 24. Holder H Needle......1 you use best tip hole size for that coating and best fan 25. Shell..........1 width for that surface. 26. -
Page 15: Reversible Tip Selection Chart
Reversible Tip Selection Chart Fan Width 12 in Tip Part No: (305 mm) from Hole Size surface 6-8 in. 0.011 in. Alt311 (152-203mm) (0.28mm) 8-10 in. 0.011 in. Alt411 (203-254mm) (0.28mm) 6-8 in. 0.013 in. Alt313 (152-203mm) (0.33mm) 8-10 in. 0.013 in.
Need help?
Do you have a question about the DP6388B and is the answer not in the manual?
Questions and answers