Da-Lite LARGE ADVANTAGE DELUXE ELECTROL Instruction Book
  1. Manuals
  2. Brands
  3. Da-Lite Manuals
  4. Projection Screen
  5. LARGE ADVANTAGE DELUXE ELECTROL
  6. Instruction book

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL Instruction Book

Hide thumbs Also See for LARGE ADVANTAGE DELUXE ELECTROL:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Book
The Da-Lite Difference.
DA-LITE SCREEN COMPANY, INC.
Instruction Book for
3100 North Detroit Street
Post Office Box 137
Large advantage® deLuxe eLectroL®
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LARGE ADVANTAGE DELUXE ELECTROL and is the answer not in the manual?

Questions and answers

Related Manuals for Da-Lite LARGE ADVANTAGE DELUXE ELECTROL

Summary of Contents for Da-Lite LARGE ADVANTAGE DELUXE ELECTROL

  • Page 1 The Da-Lite Difference. DA-LITE SCREEN COMPANY, INC. Instruction Book for 3100 North Detroit Street Post Office Box 137 Large advantage® deLuxe eLectroL® Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www.da-lite.com e-mail: info@da-lite.com...
  • Page 2 IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. R ead and understand all instructions before using. 2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use. 3. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified serviceman. 4. P osition the cord so that it will not be tripped over, pulled, or contact hot surfaces. 5. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat. 6. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids. 7 . To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized service dealer when repair work is required. Incorrect reassembly can cause electric shock when the appliance is used subsequently. 8. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS PRE-INSTALLATION 1. Carefully unpack screen and remove outer wrapping from case. 2. Make sure to recheck measurements of screen location before installation. Please Note: Motor Operator Projection Screen Models LADT, LADDT, LAD and LADD must be installed in accordance with the requirements of the DOOR SUPPORT SCREWS...
  • Page 3 SCREEN AND ROLLER ASSEMBLY INSTALLATION If your screen was shipped with the motor and roller already installed proceed to step 7 . 1. R emove four bolts from ends of door assembly (2 bolts on each end) (Fig. 1). This will allow the door assembly to drop open for access to case. For larger sizes, you will also need to remove the door support screws. 2. Carefully unpack screen and roller assembly. Leave packing paper on the roller. 3. Remove the square peg bracket from the motor end of the roller assembly. 4. Remove the safety clip from the motor attachement bracket located in the motor end of the screen housing. 5. Place the roller assembly into the case with the motor on the left side. The limit switches should be facing down. Line up the head of the motor with the motor attachment bracket. 6. Loosen four bolts that secure pin end mounting bracket into housing. Lift pin end of roller into position and slide the bracket into the roller pin. Tighten all four bolts. 7 . Complete electrical hook-up by snapping motor 1/3 wire connectors into case connectors. 8. Return to motor end and insert safety clip over casting bracket to secure motor end. CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND. 9. Carefully remove tape strips securing picture surface around roller. Slat should move freely (Fig. 2). (Only if the roller assembly is pre installed.) 10. Test installation by operating the screen several times. Be prepared to stop the screen. The door assembly will not...
  • Page 4 0" or 2" black at the top. See the specification data sheet for details. 3. R ecalibrate according to above instructions. Press "up" button to close door after recalibration. LESS SCREEN DROP 1. R aise picture surface approximately two feet above desired level. 2. P lace operating switch in “off”position. 3. T urn the white “down” limit switch (Fig. 2) one-quarter turn clockwise. Test by raising picture surface approximately two feet, then lower again. Repeat until desired picture surface position is attained. 4. R ecalibrate according to above instructions. Press "up" button to close door after recalibration. CONTACT DA-LITE AT 800-622-3737 IF DOOR MOTOR NEEDS ADjUSTMENT.
  • Page 5 LARGE ADVANTAGE DELUXE ELECTROL INSTRUCTIONS ® ® FRONT OF BACK OF NOTE: 20-24AWG WIRE RECOMMENDED WALL WALL FOR CONNECTING WALL SWITCH TO 120V WIRING DIAGRAM SWITCH SWITCH DUAL MOTOR CONTROLLER. WHITE STOP (COMMON) DOWN BLACK (DOWN) “EYE” PORT WHITE (COMMON) (UP) PLUG “IR”...
  • Page 6 LARGE ADVANTAGE DELUXE ELECTROL INSTALLATION ® ® (SUGGESTED) " THREADED ROD (NOT INCLUDED) ATTACHED TO MOUNTING SCREEN ROLLER BRACKET " AUDIENCE SIDE " " 11" DOOR ROLLER SELF-TRIMMING ACCESS DOOR FLANGE FINISHED SELF-TRIMMING CLOSING DOOR CEILING FLANGE " " " 11" VARIABLE CASE LENGTH POSITION " MOUNTING BRACKETS " ELECTRICAL JUNCTION BOX "...
  • Page 7 TROUBLESHOOTING SYMPTOM CAUSE SOLUTION 1. S creen will not operate or will not go (a) I ncorrect line voltage. (a) V erify 115-125V (or 220-240V). If “down”. insufficient voltage, rewire incoming Motor does not hum. electric line. (b) B lown facility fuse. (b) R eplace facility fuse. (c) T ripped facility circuit breaker. (c) R eset facility circuit breaker. (d) N o power to operating switch or (d) C heck above. Tighten all loose wire junction box.

  • Page 8: Troubleshooting

    INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE. In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137 , Warsaw, IN 46581-0137 , (574) 267-8101, (800) 622-3737 . IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA-LITE’S WRITTEN INSTRUCTIONS. Keep your sales receipt to prove the date of purchase and your original ownership.

This manual is also suitable for:

Tensioned large advantage deluxe electrol

Table of Contents