ShockWave 26 EP Rally Sport Owners Manual Electric Deep-V Boat Specifications Hull Length ..................26 in (660mm) Beam ....................7.5 in (191mm) Motor ............Water-cooled hi-performance 550-size Radio System............ProBoat AM 27 mHz Pistol-grip Drive System ..................Direct Drive Steering System ..............Steerable Drive System Speed Control ...........Waterproof Electronic with Reverse...
Introduction The ShockWave 26 RS comes Ready-To-Run Thank you for purchasing the Pro Boat ™ with the Pro Boat 27MHz AM radio system and ShockWave ™ 26 EP Rally Sport Ready-To-Run electronic speed controller already installed. boat. Please read these instructions carefully before All assembly and building is done at the factory, attempting to operate your boat.
Do not operate your boat again until full-scale boats, stationary objects and wildlife. It you are certain the problem has been corrected. is preferable to operate the ShockWave 26 in low Always stay clear of the propeller. wake, low wind conditions and in areas free of people, wildlife and objects.
Limited Warranty (a) This warranty is limited to the original Purchaser (c) Purchaser Remedy- Horizon's sole obligation ("Purchaser") and is not transferable. REPAIR OR hereunder shall be that Horizon will, at its option, REPLACEMENT AS PROVIDED UNDER THIS (i) repair or (ii) replace, any Product determined by WARRANTY IS THE EXCLUSIVE REMEDY OF Horizon to be defective.
Safety Precautions This is a sophisticated hobby Product and not a The Product manual contains instructions for safety, toy. It must be operated with caution and common operation and maintenance. It is essential to read sense and requires some basic mechanical ability. and follow all the instructions and warnings in the Failure to operate this Product in a safe and manual, prior to assembly, setup or use, in order to...
Warranty Inspection and Repairs Repair or replacement decisions are at the sole To receive warranty service, you must include discretion of Horizon Hobby. your original sales receipt verifying the proof-of- purchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge.
Safety, Precautions, and Warnings As the user of this product, you are solely • Always operate your model in an open area away responsible for operating it in a manner that does from people. not endanger yourself and others or result in •...
Inspect the boat to make sure no damage is present. If you notice damage is present, please contact the hobby shop where you purchased it. Contents • Assembled ShockWave 26 EP RS RTR • Pro Boat radio transmitter • Boat stand...
Section 1: Installation of the Transmitter Batteries Install 8 “AA” alkaline batteries into the transmitter, following the instructions provided for your radio system. Section 2: Installation of the 7.2V Ni-Cd Battery Pack Turn on your transmitter, making sure the radio Install a fully charged 7.2V Ni-Cd battery pack into the radio box.
Section 3: Checking the Radio System Ensure the antenna tube is properly placed through the hull. It may be necessary to slightly pull the antenna tube out to make certain the radio range is sufficient. Left Turn With the propeller free from any objects, give some throttle input to ensure that the motor is working.
Section 5: Handling Adjustment Operate your ShockWave 26 RS in low to medium You may also turn the dual rate dial down to wake conditions to avoid having problems with the reduce rudder travel in rough water conditions.
Section 6: Connecting the Battery to the ESC The Pro Boat ESC comes pre-wired with a Tamiya- style connector compatible with most battery packs. Use a 6- to 7-cell battery pack. 1. Make sure the On/Off switch is in the "OFF"...
Section 8: Speed Control Programming The ESC in your ShockWave 26 RS is pre- 4. To reset the maximum throttle setting, simply programmed from the factory. The following has turn the ESC's power switch off then on and been provided if you happen to need to reset the move the throttle stick to full movements again.
Apply Lubricant the mount. Make sure not to lose the 3mm nuts when removing the screws. Note: Running the ShockWave 26 EP RTR in salt water could cause some parts to corrode. If you run the boat in salt water, rinse it thoroughly in fresh water after each use and lubricate the drive system.
Section 11: Replacement Parts If you have any questions concerning the setup or running of your ShockWave 26 EP RS, please call the Horizon Service Center toll-free at (877) 504-0233. PRB2507 Drive Dog and Prop Shaft PRB2314 Electronic Speed Controller...