Table of Contents
Advertisement
1/12-Scale RTR Nitro Unlimited Hydroplane
Owner's Manual
Specifications
Overall Length ............................................................................................ 27.5 in (698.5 mm)
Beam ............................................................................................................ 14 in (355.6 mm)
Engine ................................................................................................ DYN .15 Marine w/Recoil
Radio System ........................................................................................ JR AM 75MHz Python
Advertisement
Table of Contents
Related Manuals for Pro Boat Miss Budweiser
Summary of Contents for Pro Boat Miss Budweiser
- Page 1 1/12-Scale RTR Nitro Unlimited Hydroplane Owner’s Manual Specifications Overall Length .................... 27.5 in (698.5 mm) Beam ......................14 in (355.6 mm) Engine ....................DYN .15 Marine w/Recoil Radio System ..................JR AM 75MHz Python...
-
Page 2: Table Of Contents
If you need to turn left, reduce throttle and turn in a very large diameter oval. When you first begin to run your Miss Budweiser, place in water with engine running at approximately 1/4 throttle. Slowly increase Service Center Information throttle until boat accelerates onto plane. -
Page 3: Additional Required Items
Clear 3M tape to seal radio box Suggested Field Equipment and Supplies In addition to the items needed to run the Miss Budweiser, we recommend that you carry the following in your field box: Engine Tuning Screwdriver (DYN2775) Replacement glow plugs (DYN2508 or DYN2500) Hex Driver/Allen Wrench (1.5 mm and 2.5 mm) -
Page 4: Section 1: Installation Of Receiver And Transmitter Batteries
Section 1: Installation of Receiver and Transmitter Batteries Receiver Batteries Remove the two knurled aluminum nuts that secure the Remove the clear lid that covers the radio box. cockpit as shown. Pull the cockpit off of the boat. Carefully note how the exhaust system is assembled. Use a Phillips screw driver to remove the tuned pipe mount as shown above. -
Page 5: Section 2: Turn Fin
Section 1: Installation of Receiver and Transmitter Batteries (cont.) Re-install the tuned pipe mount. Transmitter Batteries Remove the transmitter from the box. Re-install the battery holder back into the radio box and properly seal the radio box with clear (3M) tape. Failure to properly seal the radio box could result in damage to your radio equipment. -
Page 6: Section 3: Filling The Fuel Tank
The Miss Budweiser comes with the turn fin installed on the right Do not attempt to make tight left hand turns (counterclockwise), sponson. You will want you run the Miss Budweiser in an oval and or you could easily flip the boat. If you need to make a left turn, in an area that will allow you to make right turns (clockwise). -
Page 7: Section 5: The Dynamite .15 Marine Engine
Section 5: The Dynamite .15 Marine Engine Water-Cooled Engine During the first tank of fuel, advance the idle via the idle adjust- Because the Dynamite 15S engine is water-cooled and not air ment screw more than normal to prevent stalling at idle due to the ®... -
Page 8: Troubleshooting Guide
Wipe off any exhaust residue from the boat. If you have operated Miss Budweiser in salt water, it is suggested that you thoroughly Before operating Miss Budweiser rinse the deck, hull, and all the metal hardware with fresh water, Check that all screws and hardware are securely in place. - Page 9 Section 6: Maintenance (cont.) Lubrication It is important to lubricate the drive shaft of the Miss Budweiser with silicone cable grease after every two hours of operation. Do not forget to do this. You can purchase this silicone grease at your local hobby store.
-
Page 10: Section 7: Replacement Parts
Section 7: Replacement Parts In the event that you need to purchase replacement parts for your engine or the Miss Budweiser, please see your local hobby store. You can also purchase them from Horizon Hobby by calling 1-800-338-4639 or shop online @ www.horizonhobby.com... -
Page 11: Appendix
Appendix Photo 1 Photo 2 Pull Starter Fuel Tank Water-Cooling Line Water-Cooling Line Water-Cooled Head Rubber Boot Carburetor Carburetor Coupler Rudder Exhaust Manifold Water Intake for Cooling Glow Plug Fuel Line Photo 3 Photo 4 Turn Fin 2.5 mm Muffler Bolts... - Page 12 MADE IN CHINA © Copyright 2002 Horizon Hobby, Inc. www.horizonhobby.com 4517...