Hdmi Input - Integra DTR-70.2 Instruction Manual

■
Resolution
You can specify the output resolution for the HDMI
and COMPONENT VIDEO MONITOR OUT and have
the AV receiver upconvert the picture resolution as neces-
sary to match the resolution supported by your TV.
*1
Through :
Select this to pass video through the AV receiver at
the same resolution and with no conversion.
*2
Auto :
Select this to have the AV receiver automatically
convert video at resolutions not supported by your
TV.
480p (480p/576p):
Select this for 480p or 576p output and video con-
version as necessary.
720p:
Select this for 720p output and video conversion as
necessary.
1080i:
Select this for 1080i output and video conversion as
necessary.
1080p *2 :
Select this for 1080p output and video conversion as
necessary.
1080p/24 *2 :
Select this for 1080p output at 24 frames per second
and video conversion as necessary.
Source:
Output will be according to the resolution level
which was set in the "Picture Adjust" setting
63).
(➔
Tip
• The "Resolution" setting is set respectively of main, sub, and
analog.
• You can see the picture by pressing Enter to check the "Resolu-
tion" setting (excluding NET/USB input source).
Note
• If the "Monitor Out" setting is set to "Both", this setting is fixed
at "Auto".
• Depending on the incoming video signal, video playback may
not be smooth or the vertical resolution may be lowered. In this
case select other than "1080p/24".
*1
PC IN (Analog RGB) input signal is output at 480p
(480p/576p), 720p, 1080i resolution when the "Monitor Out"
setting is set to "Analog" (➔
ting is set to "Through".
*2
These settings are not available when the "Monitor Out" set-
ting is set to "Analog" (➔
output
50) and the "Resolution" set-
50).

HDMI Input

If you connect a video component to an HDMI input, you
must assign that input to an input selector. For example, if
you connect your Blu-ray Disc/DVD player to HDMI
IN 2, you must assign "HDMI 2" to the "BD/DVD" input
selector.
If you've connected your TV to the AV receiver with an
HDMI cable, composite video, S-video and component
video sources can be upconverted
HDMI output *1 . You can set this for each input selector by
selecting the "- - - - -" option.
Composite video, S-Video,
component video
Composite video, S-Video,
component video
*1
This applies only when "Monitor Out" setting is set to other
than "Analog" (➔ 50).
Here are the default assignments.
Input selector
BD/DVD
VCR/DVR
CBL/SAT
GAME
PC
AUX
TAPE
TUNER
TV/CD
PHONO
PORT
■
BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TAPE,
TV/CD, PHONO, PORT
HDMI 1, HDMI 2, HDMI 3, HDMI 4, HDMI 5,
HDMI 6, HDMI 7:
Select the HDMI IN to which the video component
has been connected.
- - - - -:
Output composite video, S-Video, and component
video sources from the HDMI output. The video out-
put signal from the HDMI output is the one config-
ured in "Component Video Input"
• "AUX" is used only for input from the front panel.
• Each HDMI input cannot be assigned to two input selec-
tors or more. When HDMI 1 - HDMI 7 have already
been assigned, you must set first any unused input selec-
tors to "- - - - -" or you will be unable to assign HDMI 1
- HDMI 7 to input selector.
* and output by the
HDMI
IN
OUT
HDMI
Default assignment
HDMI 1
HDMI 2
HDMI 3
HDMI 4
HDMI 5
FRONT (Fixed)
- - - - -
- - - - - (Fixed)
- - - - -
- - - - -
- - - - -
(➔ 52).
En
51