Level Calibration; Equalizer Settings - Integra DTR-70.2 Instruction Manual

Level Calibration

This setting is set automatically by
Audyssey MultEQ
Speaker Setup function
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■
Left, Front Wide Left, Front High Left, Center
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right,
Surround Back Left, Surround Left
–12.0dB to 0.0dB to +12.0dB in 0.5 dB step.
■
Subwoofer 1 *1 , Subwoofer 2
–15.0dB to 0.0dB to +12.0dB in 0.5 dB step.
Note
• Speakers that you set to "No" or "None" in the
"Speaker Configuration" cannot be selected
• The speakers cannot be calibrated while the AV receiver is
muted.
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at vol-
ume settings below this, be careful because the test tone will be
much louder.
• The "Level Calibration" setting cannot be selected if "Audio
TV Out" setting is set to "On".
*1
For the center speaker and subwoofer, the level settings made
by using the Home menu are saved
*2
If the "Subwoofer" setting is set to "1ch", this setting cannot
be selected (➔ 54).
Tip
• If you're using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
En
56
®
XT32 Room Correction and
(➔ 29).
*1*2
(➔ 54).
(➔ 27).

Equalizer Settings

This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function (➔
With the Equalizer settings, you can adjust the tone of
speakers individually with a 15-band equalizer. The vol-
ume of each speaker can be set
■
Equalizer
*1 ,
Manual:
You can adjust the equalizer for each speaker manu-
ally. If you selected "Manual", continue with this
procedure.
1
Press to select "Channel", and then use
/ to select a speaker.
2
Use / to select a frequency, and then use
the /
The volume at each frequency can be adjusted
from –6dB to 0dB to +6dB in 1 dB steps.
Note
• You can select: "25Hz", "40Hz", "63Hz",
"100Hz", "160Hz", "250Hz", "400Hz", "630Hz",
"1000Hz", "1600Hz", "2500Hz", "4000Hz",
"6300Hz", "10000Hz", or "16000Hz". And for the
subwoofer, "25Hz", "40Hz", "63Hz", "100Hz", or
"160Hz".
• While the Direct listening mode is selected, the
equalizer settings have no effect.
Tip
• Low frequencies (e.g., 63Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.
3
Use to select "Channel", and then use
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to "No"
or "None" in the "Speaker Configuration"
(➔ 54).
Audyssey:
This is selected automatically by
Audyssey MultEQ XT32 Room Correction and
Speaker Setup function. The Audyssey indicator will
light (➔ 9) and "Dynamic EQ" and
"Dynamic Volume" become available
When "Audyssey" is selected, "Dolby Volume"
becomes "Off" automatically
Off:
Tone off, response flat.
29).
(➔ 56).
to adjust the level at that frequency.
(➔
58).
(➔
/
60).