Integra DTR-70.2 Instruction Manual page 88

Controlling Zone 2/3/4 with the Remote
Controller
Standby
On
Input
Selector
Note
• To control Zone 2/3/4, you must press the remote controller's
Zone first.
• Zone turns red while Zone 2 is on, and green while Zone 3 is on,
and amber while Zone 4 is on.
1
Press Zone repeatedly, then point the remote con-
troller at the AV receiver and press On.
Tip
• The 12V TRIGGER OUT goes high (+12 V).
2
To select an input source for Zone 2/3/4, press
Zone repeatedly, followed by Input Selector.
To select AM or FM, press Tuner input selector and
Zone repeatedly.
(North American models) You can also select SIR-
IUS.
3
To turn off Zone 2/3/4, press Zone repeatedly, fol-
lowed by Standby.
Note
• Only analog input sources are output by the Zone 2/3 PRE
OUT and FRONT WIDE/ZONE 2 L/R, SURR
BACK/ZONE 3 L/R, SURR/ZONE 4 L/R terminals. Digital
input sources are not output. If no sound is heard when an input
source is selected, check if it's connected to an analog input.
• You cannot select different AM or FM radio stations for your
main room and Zone 2/3/4. The same AM/FM radio station will
be heard in each room. For example, if you have an FM station
for the main room, that station will also be used in Zone 2.
• When you connect Zone 2 speakers directly to the AV receiver,
listening modes that require front wide speakers such as
Audyssey DSX™ are unavailable.
• When you connect Zone 3 speakers directly to the AV receiver,
listening modes that require surround back speakers such as
Dolby EX, DTS-ES or THX Ultra2 Cinema are unavailable.
• When you connect Zone 4 speakers directly to the AV receiver,
listening modes that require surround speakers are unavailable.
• When the input selector of Zone 2/3/4 is selected, power con-
sumption on standby mode slightly increases.
• While Zone 2/3/4 is on,
En
88
Zone
functions will not work.
Adjusting the Volume for Zones
On the remote controller, press Zone repeatedly,
and then use VOL / .
On the AV receiver, press Zone 2, Zone 3 or
Zone 4 (the Zone 2/3/4 indicator and Zone 2/3/4
selector on the display flashes) and press Zone
Level / within 8 seconds.
Muting Zones
On the remote controller, press Zone repeatedly,
and then press Muting.
To unmute a zone, on the remote controller, press
Zone, and then press Muting again.
Adjusting the Tone and Balance of Zones
1
On the AV receiver, press Zone 2 or Zone 3.
2
Press the AV receiver's Tone repeatedly to select
"Bass", "Treble" or "Balance".
3
Use –/+ to adjust the bass, treble or balance.
• You can boost or cut the bass or treble from –10 dB
to +10 dB in 2 dB steps.
• You can adjust the balance from 0 in the center to
+10 dB to the right or +10 dB to the left in 2 dB
steps.
Note
• Zones can also be unmuted by adjusting the volume.
• The Zone 2 volume, tone, and balance function have no effect on
ZONE 2 PRE OUT when the "Zone 2 Out" setting is set to
"Fixed" (➔ 86) and "Powered Zone 2" setting is set to "Not
Act" (➔ 86).
• The Zone 3 volume, tone, and balance function have no effect on
ZONE 3 PRE OUT when the "Zone 3 Out" setting is set to
86) and "Powered Zone 3" setting is set to "Not
"Fixed" (➔
Act" (➔ 86).
• Even if you repeatedly press the remote controller's Zone to
select zones, the last zone selection will be retained once you
have switched to other components by pressing other Remote
Mode after pressing Zone.