Introduction; Installation - Montigo HR38DF Installation, Operation & Maintenance Manual

Thank You for choosing a Montigo Gas Fireplace.
About this Fireplace:
The H38DF-Series is an line of fireplace's with a standard LogSet,
also Linear-style burner, or Stainless steel, and Premium model. These
fireplaces can be converted to both a Top Vent or Rear Vent application,
and are available in the specific models below.
The H38DF is rated for Natural Gas and Liquid Propane at 26,000 Max.
BTU/H (7.62) Kilowatts Input.
► H38DF; Top or Rear Vent convertible, Millivolt Pilot
► H38DF-I; Top or Rear Vent convertible, Intermittent Pilot (HSI)
► H38DF-F; Top or Rear Vent convertible, ( IPI Electronic Ignition).
The HL38DF is rated for Natural Gas and Liquid Propane at 26,000 Max.
BTU/H (7.62) Kilowatts Input.
► HL38DF; Top or Rear Vent convertible, Millivolt Pilot
► HL38DF-I; Top or Rear Vent convertible, Intermittent Pilot (HSI)
► HL38DF-F; Top or Rear Vent convertible, ( IPI Electronic Ignition).
The HR38DF is rated for Natural Gas at 26,000 Max. BTU/H (7.62)
Kilowatts Input.
► HR38DF; Top or Rear Vent convertible, Millivolt Pilot
► HR38DF-I; Top or Rear Vent convertible, Intermittent Pilot (HSI).
CAUTION!
Due to its high operating temperatures, the appliance
should be located out of traffic & away from furniture and
draperies.
Children and adults should be alerted to the hazards

of the high surface temperature, which could cause
burns or clothing ignition.
Young children should be carefully supervised when

they are in the same room as the appliance.
Clothing or other flammable materials should not be

placed on or near the appliance.
Part No. XG0147 - 011410

Introduction

This manual covers installation, operation and maintenance. Lighting,
operation and care of this fireplace can be easily performed by the
homeowner. However, all installation and service work should be
performed by a qualified or licensed installer, plumber, or gas fitter who
is qualified or licensed by the state, province, region, or governing body
in which the appliance is being installed.
This manual covers all models and unless otherwise specified, the
designation H38DF refers to all variations of the model above. Sections
which are specific to a particular variation are marked with a
symbol, plus the appropriate model number.
Warranty and Installation Information:
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
► Modification of the fireplace and/or components including Direct-Vent
assembly or glass doors.
► Use of any component part not manufactured or approved by Montigo in
combination with this Montigo fireplace system.
► Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done by
a qualified contractor.
Installations in Canada must conform to the current CAN/CGA B-149.1
and .2 Gas Installation Code and local regulations. If the optional air-
circulating fan kit is installed, it must be electrically grounded in accordance
with CSA C22.1 Canadian Electrical Code Part 1 and/or Local Codes.
Installations in the USA must conform to local codes, or in the absence
of local codes to the National Fuel Gas Code, ANSI Z223.1-1988. If the
optional air-circulating fan is installed, it must be grounded in accordance
with local codes or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70-1987. See Appendix for installation
within the State of Massachusetts. This fireplace must comply with
NFPA-54 Chapter 10.
When this appliance is installed directly on carpeting, tile or any
combustible material other than wood flooring, it must be installed
on a metal or wood panel extending the full width and depth of
the appliance.
H38DF Series Gas Fireplace
WARNING!
Page 3