Montigo H42DF Installation & Maintenance Manual
Montigo H42DF Installation & Maintenance Manual

Montigo H42DF Installation & Maintenance Manual

Indoor residential gas fireplace
Table of Contents

Advertisement

Installation & Maintenance Manual
XW2002
XW2004
XG0148
DANGER
Read and understand this manual.
Improper installation, adjustment,
alteration, service or maintenance
can cause serious injury, property
damage
or
even
assistance or additional information
consult a qualified installer, service
agency or the gas supplier.
CAUTION
Glass doors on gas fireplaces are
extremely hot while the fireplace is
on and remain hot even after the
fireplace has been turned off. Safety
screens are available and can reduce
the risks of severe burns. Please
keep children away from the fireplace
at all times.
®
C
US
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
death.
For
XW2006
XW2012
XW2014
H42DF HL42DF
HR42DF
Indoor
Residential
Gas Fireplace
WARNING
Do not store or use gasoline or any
other flammable vapors and liquids in
the vicinity of this or any other gas
burning appliance. A fire or explosion
my occur causing serious injury,
property damage or even death.
NOTICE
Installer: Leave this manual with the
appliance. Do not remove.
Consumer: Retain this manual for
maintenance and future reference. Do
not Discard.
NOTICE
Blank
IF YOU SMELL GAS
Blank
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Do not try to light any appliance.
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Do not touch any electrical switch; do
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Blank
not use any phone in your building.
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Immediately call your gas supplier
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
falling objects
from a neighbor's phone. Follow the gas
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Blank
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
falling objects
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
supplier's instructions.
radiation
Environment
your hands
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
If you cannot reach your gas supplier,
radiation
Environment
your hands
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
falling objects
call the fire department.
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
radiation
Environment
your hands
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
042811

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H42DF and is the answer not in the manual?

Questions and answers

Summary of Contents for Montigo H42DF

  • Page 1 Danger of harming radiation Environment your hands Irritant Slippery floor Watch your step Cutting High temperatures Glass hazard Danger of suffocation XW2014 XG0148 042811 Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248...
  • Page 2: Table Of Contents

    ▪ Roof mounted Terminations Section 8: Installing the Accessories ..........21 - 23 Standard Top Vent (no elbows or offsets)........9 ▪ Installing the H42DF Log Set .............21 Top Vent (two elbows one offset) ...........9 ▪ Installing the HL42DF Firestones ..........22 Top Vent (multi-elbows and offsets) ..........9 ▪...
  • Page 3: Introduction

    Introduction Congratulations on your purchase of a Montigo Fireplace. With over 30 years of experience, Montigo is committed to providing you with a gas fireplace that is not only a beautiful addition to your space, but that is also designed and manufactured to the highest safety, reliability and engineering standards.
  • Page 4: Before You Start

    Should it be impossible to meet the venting requirements laid BEFORE YOU START: „ out in Section 3: Venting, please contact Montigo regarding the use of a Montigo Power Vent. Lay out the Vent run; calculating the required elbows and straight „...
  • Page 5: Section 1: Installation Overview And Product Dimensions

    H*42DF Indoor Gas Fireplace Installation 0" cl to co 0" clearance Section 1: Installation Overview and Product Dimensions to corners onl y Please review the Installation Checklist on Page 4 for general information Safety, as well as efficiency of operation, should be considered when M”...
  • Page 6: Section 2: Framing The Fireplace

    H*42DF Indoor Gas Fireplace Installation Section 2: Framing Frame in the enclosure for the unit with framing materials. The framed opening for the assembled fireplace is 42" wide, x 46 1/2" Top Vent high x 21 5/8" deep, see Figure 2 Ceiling level Non-Combustible nOTE: when constructing the framed opening, please ensure...
  • Page 7: Clearances

    H*42DF Indoor Gas Fireplace Installation Clearances Installing The Standoffs To avoid elevated mantel temperatures, all H*42DF*-Series gas When installing a shelf over the top of the fireplaces, the following fireplaces are required to have the supplied standoffs installed. guidelines must be adhered to: The fireplace is supplied with two standoffs.
  • Page 8: Section 3: The Direct Vent System

    H*42DF Indoor Gas Fireplace Installation Section 3: Venting Montigo supplies a variety of direct venting and termination options. 4. Install the (5" and 8") collars to the rear vent outlet using the The direct vent termination location MUST be selected such that included hardware, as illustrated Figure 9a.
  • Page 9: Section 3-2: Installing A Roof Mounted Termination

    H*42DF Indoor Gas Fireplace Installation Section 3-2: InSTaLLInG a ROOF MOUnTED DIRECT VEnT PVTK1 TERMInaTIOn (PVTK-1) Termination This section applies to installations where the direct vent termi- 2’ min. nation will be roof mounted. Support ring Section 3-2-1: VEnTInG LaYOUT Selection of components and details of venting lay out should Support plate 32’...
  • Page 10: Standard Roof Vent (One Elbows No Offsets)

    Max. and inner pipes to keep the pipes separate and avoid any possible hot spots. Montigo recommends the use of a flex section for the final pipe „ Figure 11c. Rear vent, Roof mounted venting (1 = 90° bend). connected directly to the fireplace offering greater flexibility of installation and absorption of movement.
  • Page 11: Section 3-3: Installing A Wall Mounted Termination

    H*42DF Indoor Gas Fireplace Installation 4). Installation of termination from inside structure Section 3-3: InSTaLLInG a waLL MOUnTED DIRECT VEnT A Termination with a MOSR Frame is installed from the inside of the TERMInaTIOn structure. These are commonly used in high-rise construction. This section applies to installations where the direct vent termi- nation will be wall mounted.
  • Page 12: Section 3-3-1: Venting Layout

    All through-the-wall terminations beyond 3' of the fireplace must „ within the venting graph para- have a Montigo Heat Shield (RHS8) installed. See Section 3-3-3. meters, please contact Montigo for Power Venting options. Once the proposed venting layout has been determined refer to „...
  • Page 13: Top Vent, Wall Mounted Termination (45° Corner)

    If your installation does not fall 33” within the venting graph para- 18” meters, please contact Montigo for Power Venting options. Figure 16c. Flex installation. (NG Models Only) note: Through the wall venting kits are also available for both Figure 17. Rear Vent Venting Graph for wall mounted terminations.
  • Page 14: Rear Vent, Wall Mounted Termination Graph

    H*42DF Indoor Gas Fireplace Installation Section 3-3-3: Heat Shields Installing a wall Mounted RHS101 Heat shield. Installing a wall Mounted RHS8 Heat shield The RHS101 Heat shield MUST be used where the RHS8 Termination (Figure 19 and 19a) CannOT be used. Use the RHS101 within 36" horizontal or 46"...
  • Page 15: Section 3-3-2: Venting Components

    Place the springs, supplied with the pipe kit, between the outer and „ inner pipes to keep the pipes separate and avoid any possible hot spots. Montigo recommends the use of a flex section for the final pipe „ connected directly to the fireplace offering greater flexibility of installation and absorption of movement.
  • Page 16: Section 3-3-3: Heat Shields

    H*42DF Indoor Gas Fireplace Installation Section 4: wiring Honeywell (Q3450) Pilot Assembly Pilot Electrical Harness Connector Models H42DFnE H42DFLE Honeywell Gas Control (SV9501M) Gas Control Connector Junction Box Fan Plug Receptacle Black 115VAC White 24VAC Green Gnd Screw 40 VA Transformer Wall Switch Figure 20.
  • Page 17: Honeywell Gas Control And Pilot

    H*42DF Indoor Gas Fireplace Installation Models H42DFnI H42DFLI HL42DFnI HL42DFLI HR42DFnI Figure 21. Wiring for the SIT IPI Wiring Schematic nOTE: If any of the original wire supplied with the appliance is replaced, it Wiring for the optional Fan Kit must be replaced with the same type, or its equivalent.
  • Page 18: Section 5: Installing The Gas Line

    To check pressures, control valves have a provision to remove „ a 1/8” N.PT. plug to be fitted with a hose barb. Montigo requires a service shut off valve be located in an „ accessible location to isolate the gas supply.
  • Page 19: Section 6: Finishing

    H*42DF Indoor Gas Fireplace Installation Section 6: Finishing Finishing around the Fireplace Painting: Combustible mantels and mouldings may be safely installed over the Special care is recommended by the Master Painters and Decorators top and on the front of the fireplace provided that they do not project Association, when painting the fireplace surrounds, to select and apply beyond shaded area shown in Figure 24.
  • Page 20: Section 7: Installing And Removing The Door

    H*42DF Indoor Gas Fireplace Installation Section 7: Installing & Removing the Door Removing the door: The H*42DF* doors are removed in a few simple steps. Follow these Step 5: below to remove the Horizontal access panel, unlatch the door buckles Ensure the tool is firmly and, remove the door.
  • Page 21: Section 8: Installing The Accessories

    Step 5. Place the Centre Front log , Figure 27d below, as shown using the notch cast in the Bottom Rear log as shown in figure 27c above. The H42DF* is supplied with a seven ceramic fibre log logset. Unpack the logs and handle them very carefully.
  • Page 22: Installing The Hl42Df Firestones

    The H*42DF* has the option of installing the cultured rocks which mimic real stone. These may be spaced at random, or in a visual pattern of Figure 28b. Spreading the firestones evenly . your preference. See the Montigo web site for photographs and ideas www.montigo.com Figure 28c. Completed firestone installation.
  • Page 23: Installing The Hr42Df Artificial River Rocks

    H*42DF Indoor Gas Fireplace Installation Installing the artificial River Rocks: Place (18) eighteen faux rocks "D" as shown below. The HR42DF* is supplied with (37) thirty-seven faux ceramic fibre river rock. Unpack the rocks and handle them very carefully. Shown Below: Remove the glass door as described in the previous Instructions.
  • Page 24: Section 9: Operation

    H*42DF Indoor Gas Fireplace Operation Section 9: Start-up Sequence with Continuous Pilot with American Flame Electronic Ignition For Your Safety - READ BEFORE LIGHTING: WARNING Models If the information in these instructions is not followed exactly, a fire or explosion H42DFn HR42DFn may result causing property damage,...
  • Page 25: Start-Up Sequence With Honeywell Electronic Ignition

    H*42DF Indoor Gas Fireplace Operation with Honeywell Electronic Ignition For Your Safety - READ BEFORE LIGHTING: with American Flame Electronic Ignition Models WARNING H42DFnE H42DFLE If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
  • Page 26: Start-Up Sequence Sit-Ipi Gas Valve

    H*42DF Indoor Gas Fireplace Operation Proflame SIT Electronic Ignition For Your Safety - READ BEFORE LIGHTING: with American Flame Electronic Ignition Models WARNING H42DFnI HL42DFnI HR42DFnI H42DFLI HL42DFLI If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
  • Page 27: Maintenance

    H*42DF Indoor Gas Fireplace Maintenance Models Hi-Lo Burner Lighting Instructions H42DFn Adjustment: See pages 24 to 26. H42DFL (SIT Nova 820). General The H*42DF* is equipped with an adjustable burner, allowing you to Have the fireplace and installation inspected yearly. The inspection „...
  • Page 28: Troubleshooting

    H*42DF Indoor Gas Fireplace Maintenance Models Models Troubleshooting Troubleshooting: H42DFn HR42DFn H42DFnE (SIT nova 820). (Honeywell) H42DFL H42DFLE The following is a troubleshooting chart of possible problems: PROBLEM CORRECTIVE aCTIOn Noisy Pilot Flame Locate pilot adjustment screw on gas control valve. Flame is decreased by turning adjustment screw clockwise.
  • Page 29: Parts List

    H*42DF Indoor Gas Fireplace Replacement Parts H42DF HL42DF HR42DF RGC1006 RGC1006 RGC1006 nG Gas Valve RGC1005 RGC1005 LP Gas Valve RPA020 RPA020 RPA020 nG Pilot RPA021 RPA021 LP Pilot RBH3801 RBH3801 nG Burner RBH3802 LP Burner R0R1120 R0R1120 nG Orifice...
  • Page 30: Appendix

    H*42DF Indoor Gas Fireplace Appendix appendix a: Termination Locations A = clearance to the termination frame above grade, veranda, porch, deck, Q = clearance above a roof [24 inches (61 cm) minimum] or balcony [16 inches (41 cm) minimum] R = clearance to adjacent walls and neighboring buildings [18 inches (46 B = clearance to door, or sides and top of window, that may be opened [16 cm) minimum] inches (41 cm) minimum for appliances ≤100 000 BTU/H (30kW)]...
  • Page 31: Warranty

    The duration of any implied warranty with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above may not apply to you.
  • Page 32: State Of Massachusetts

    H*42DF Indoor Gas Fireplace Appendix appendix C: State of Massachusetts amendment (Gas Fireplace / Equipment sold in the State of Massachusetts) 5.08: Modifications to nFPa-54, Chapter 10 (1) Revise nFPa-54 section 10.5.4.2 by adding a second exception as follows: Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device that will automatically shut off the gas to the burner in the event of a sustained back-draft (2) Revise 10.8.3 by adding the following additional requirements:...
  • Page 33 H*42DF Indoor Gas Fireplace Notes Page 33 XG0148 - 042111...
  • Page 34 H42DF Residential Gas Fireplace Ferndale, washington Langley, British Columbia TF: 1.800.789.6236 TF: 1.800.378.3115 FX: 1.866.3000.0927 FX: 1.604.607.6462 XG0148 - 042111...

This manual is also suitable for:

Hl42dfHr42df

Table of Contents