Configuring Ip - Cisco Codec C Series Getting Started Manual

Cisco TelePresence Video Systems
Contents

Configuring IP

(When not set by a provisioning system)
Your video conference system supports IP version 4 (IPv4),
IP version 6 (IPv6) and Dual, which is the default setting. In all
three cases, the IP parameters can be assigned automatically
by the network, or you can set everything manually. When set
to Dual, the network interface can operate on both IP versions,
and have both an IPv4 and an IPv6 address.
If you wish to set the parameters manually, contact your network
administrator to obtain the required parameters.
If you choose to set the IP settings manually while using the
Dual mode, you have to set both the IPv4 and the IPv6 settings.
Start from point 2 in the instructions.
If your system is provisioned automatically, these IP settings
may be overridden by the provisioning system.
If an IPv4 or IPv6 address is already assigned to the system, you
can find it on the System Information page. Go to
tab and choose System Status and Network.
NOTE: You must restart the system after changing the IP stack
settings for the changes to take effect.
NOTE: It is not recommended to manually change the IP addres
using the web interface.
If you are changing a value setting,
you have to always click save to confirm the change.
Back to task overview
D14639.12 Video Systems Getting Started Guide TC7.0, DECEMBER 2013.
Introduction User interfaces
To set or change the IPv4 settings
Go to the Configuration
1. Choose IP version
Click the Network
from the IPStack
2. If you wish to set IP Assignment manually
In the IPv4
SubnetMask
Scroll up to the
address in the
3. Choose automatic or manual IP assignment
Scroll down the page to the
from the Assignment
IP assignment; or Static, if you have set the IP address
Configuration
manually.
* IP Assignment:
DHCPv6: All IPv6 addresses, including options like the DNS and NTP
server addresses, are obtained automatically from a DHCPv6 server.
Autoconf: The system and gateway IP addresses will be assigned
automatically. The options, e.g. NTP and DNS server addresses, must be
set/assigned according to the DHCP Options setting. **
Static: The system and gateway IP addresses must be configured
manually. The options, e.g. NTP and DNS server addresses, must be set/
assigned according to the DHCP Options setting. **
Confirguration Configuration
tab and choose System Configuration.
settings in the left sidebar. Choose
drop down list.
section, enter the Address, Gateway
in the corresponding input fields.
DNS section and enter the DNS server
Server 1 Address input field.
IPv4 section and choose DHCP
drop down list, if you want automatic
25
Appendices
To set or change the IPv6 settings
Go to the Configuration tab and choose
1. Choose IP version
IPv4 Click the Network settings in the left sidebar. Choose
from the IPStack drop down list.
2. Choose automatic or manual IP assignment
and Scroll down the page to the
DHCPv6, Autoconf or Static
down list according to your network requirements.*
3. If IP Assignment is Static: Set the IP addresses
Enter the system IP address in the
Optional: Enter the gateway address in the
field.
4. If IP Assignment is Static or Autoconf: DHCPOptions
Choose On or Off from the
according to your network requirements.**
If DHCPOptions is Off: Configure DNS and NTP
5.
Scroll up to the DNS section, and enter the DNS server
address in the Server 1 Address
Open the NetworkServices
and scroll down to the NTP
address in the Address input field. Set
** DHCP Options:
On: The IP parameters, like the DNS and NTP server addresses, will be
obtained automatically from a DHCPv6 server.
Off: The IP parameters, like the DNS and NTP server addresses, must be
set manually.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
Getting Started Guide
Contacts
System Configuration.
IPv6
IPv6 section and choose
from the Assignment drop
Address input field.
Gateway input
DHCPOptions drop down list
input field.
settings from the left sidebar,
section. Enter the NTP server
Mode to Auto.