Configuring Ip - Cisco CTS-SX10-K9 Getting Started Manual

Cisco TelePresence SX10 Quick Set
SX10 Quick Set

Configuring IP

(When not set by a provisioning system)
Your video conference system supports IP version 4 (IPv4), IP
version 6 (IPv6) and Dual, which is the default setting. In all
three cases, the IP parameters can be assigned automatically
by the network, or you can set everything manually. When
set to Dual, the network interface can operate on both IP
versions, and have both an IPv4 and an IPv6 address.
If you wish to set the parameters manually, contact your
network administrator to obtain the required parameters.
If you choose to set the IP settings manually while using
the Dual mode, you have to set both the IPv4 and the IPv6
settings. Start from point 2 in the instructions.
If your system is provisioned automatically, these IP settings
may be overridden by the provisioning system.
If an IPv4 or IPv6 address is already assigned to the system,
you can find it on the System Information page. Go to
Configuration tab and choose System Status
NOTE: It is not recommended to manually change the IP
address using the web interface.
If you are changing a value setting,
you have to always click save to confirm the change.
Back to task overview
D15117.01 SX10 Getting Started Guide TC7.1, MAY 2014.
Contents Introduction
To set or change the IPv4 settings
Go to the Configuration
1. Choose IP version
Click the Network
IPv4 from the
2. If you wish to set IP Assignment manually
In the IPv4 section, enter the Address,
SubnetMask
Scroll up to the
address in the
3. Choose automatic or manual IP assignment
Scroll down the page to the
DHCP from the
automatic IP assignment; or Static, if you have set the IP
address manually.
and Network.
* IP Assignment:
DHCPv6: All IPv6 addresses, including options like the DNS and NTP
server addresses, are obtained automatically from a DHCPv6 server.
Autoconf: The system and gateway IP addresses will be assigned
automatically. The options, e.g. NTP and DNS server addresses, must be
set/assigned according to the DHCP Options setting. **
Static: The system and gateway IP addresses must be configured manually.
The options, e.g. NTP and DNS server addresses, must be set/assigned
according to the DHCP Options setting. **
Configuration Configuration
tab and choose System Configuration.
settings in the left sidebar. Choose
IPStack drop down list.
Gateway and
in the corresponding input fields.
DNS section and enter the DNS server
Server 1 Address input field.
IPv4 section and choose
Assignment drop down list, if you want
13
Getting Started Guide
Appendices
To set or change the IPv6 settings
Go to the Configuration tab and choose
1. Choose IP version
Click the Network settings in the left sidebar. Choose
IPv6 from the IPStack drop down list.
2. Choose automatic or manual IP assignment
Scroll down the page to the IPv6 section and choose
DHCPv6, Autoconf or Static from the
down list according to your network requirements.*
3. If IP Assignment is Static: Set the IP addresses
Enter the system IP address in the Address
Optional: Enter the gateway address in the
field.
If IP Assignment is Static or Autoconf: DHCPOptions
4.
Choose On or Off from the DHCPOptions
according to your network requirements.**
5. If DHCPOptions is Off: Configure DNS and NTP
Scroll up to the DNS section, and enter the DNS server
address in the Server 1 Address input field.
Open the NetworkServices settings from the left sidebar,
and scroll down to the NTP section. Enter the NTP server
address in the Address input field. Set
** DHCP Options:
On: The IP parameters, like the DNS and NTP server addresses, will be
obtained automatically from a DHCPv6 server.
Off: The IP parameters, like the DNS and NTP server addresses, must be
set manually.
www.cisco.com — Copyright © 2014 Cisco Systems, Inc. All rights reserved.
Contact
System Configuration.
Assignment drop
input field.
Gateway input
drop down list
Mode to Auto.