Related Manuals for Crestron Cameo C2N-CBD-P
Summary of Contents for Crestron Cameo C2N-CBD-P
- Page 1 Crestron C2N-CBD-P / C2N-CBD-P-KP / C2N-CBD-E / C2N-CBF-P / C2N-CBV-P Cameo Keypads ® Operations & Installation Guide...
- Page 2 States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
-
Page 3: Table Of Contents
Crestron C2N-CBD/CBF/CBV Cameo Keypads Contents Cameo Keypads: C2N-CBD-P / C2N-CBD-P-KP / C2N-CBD-E / C2N-CBF-P / C2N-CBV-P Series Introduction ..........................1 Features and Functions ....................2 Specifications ......................7 Physical Description ....................11 Setup ............................19 Network Wiring ......................19 Identity Code ......................19 Assembly and Installation .................. -
Page 5: C2N-Cbd-P / C2N-Cbd-P-Kp / C2N-Cbd-E / C2N-Cbf-P / C2N-Cbv-P Series
1-gang wall mount form factor that is at once inviting to the touch and appealing to the eye. The C2N-CBD-P / C2N-CBD-P-KP / C2N-CBD-E / C2N-CBF-P / C2N-CBV-P easily installs alongside other low-voltage in-wall devices to deliver a fully customizable keypad control solution as part of a complete Crestron control system. -
Page 6: Features And Functions
Cameo Keypads Crestron C2N-CBD/CBF/CBV Models (Continued) DESCRIPTION MODEL NUMBER COLOR C2N-CBD-P C2N-CBD-P-DA-S Dark Almond Smooth Cameo Keypad, C2N-CBD-P-DSK-T Dusk Textured Standard Mount C2N-CBD-P-GRY-S Gray Smooth (Continued) C2N-CBD-P-IVR-S Ivory Smooth C2N-CBD-P-LAT-T Latte Textured C2N-CBD-P-W-S White Smooth C2N-CBD-P-W-T White Textured C2N-CBD-P-KP C2N-CBD-P-KP-... - Page 7 • 12 color matched smooth and textured finishes C2N-CBD-P-KP • Standard electrical box installation • Available in a white smooth finish • Pre-programmed on/off functionality (C2N-CBD-P-KP-ON-OFF) • Pre-programmed scene selection (C2N-CBD-P-KP-SCENE) (Continued on following page) Cameo Keypads • 3 Operations & Installation Guide - DOC. 7063E...
- Page 8 • Two color-matched textured finishes available 1. Split small buttons may be installed in the bottom two positions only. 2. Buttons are backlit on the C2N-CBD-P, C2N-CBD-P-KP, C2N-CBF-P, and C2N-CBV-P only. 3. Green on the C2N-CBD-E, white on the C2N-CBD-P, C2N-CBD-P-KP, C2N-CBF-P, and C2N-CBV-P.
- Page 9 Dual digital/analog input ports onboard the C2N-CBD-P, C2N-CBD-P-KP, C2N-CBF-P, and C2N-CBV-P provide a local interface for a range of devices including Crestron GLS Occupancy Sensors and Photocells (sold separately), or any device providing a contact closure, dc logic, or 0–10 volts dc analog control output. Using...
- Page 10 (C2N-CBD-P-KP-SCENE and C2N-CBD-P-KP-ON-OFF only) These unique Cameo keypads provide engraved and pre-programmed functionality directly out of the box. The C2N-CBD-P-KP-SCENE is a seven button keypad which provides control for four different scenes including up/down and off functionality. The C2N-CBD-P-KP-ON-OFF is a two button keypad which provides simple on/off functionality.
-
Page 11: Specifications
Standard Mount Model Plastic, 1-gang mountable in a standard electrical box Requires decorator style faceplate (not included) Flush Mount Model Plastic, Crestron Cameo Flush Mount with integral spring clamp Optional mud ring or 1-gang adapter (sold separately) Vimar Mount Model... - Page 12 Cameo Keypads Crestron C2N-CBD/CBF/CBV C2N-CBD/CBF/CBV Specifications (Continued) SPECIFICATION DETAILS Dimensions (Continued) Flush Mount Model Height 3.21 in (82 mm) Width 1.76 in (45 mm) Depth 1.18 in (30 mm) without connector Vimar Mount Model Height 2.97 in (76 mm) Width 2.06 in (53 mm)
- Page 13 Crestron C2N-CBD/CBF/CBV Cameo Keypads C2N-CBD/CBF/CBV Specifications (Continued) SPECIFICATION DETAILS Available Accessories (Continued) CB6[E]-BTN Small Backlit Engravable Button [A,B,BRN,DA,GRY,IVR, Cap for Cameo Keypads, Smooth, 1, 2 W]-S Includes custom engraving (specify color) CB6[E]-BTN Small Backlit Engravable Button 1, 2 [A,B,DSK,LAT,W]-T Cap for Cameo Keypads,...
- Page 14 1. Products with [E] before the first hyphen are Cameo Express keypad accessories. Do not include the [E] when other Cameo keypad accessories are desired. 2. Not available for the C2N-CBD-P-KP-ON-OFF or C2N-CBD-KP-SCENE. 10 • Cameo Keypads Operations & Installation Guide - DOC. 7063E...
-
Page 15: Physical Description
C2N-CBD-E Keypad Physical View – C2N-CBD-E-A-S Shown (Shown with Faceplate, not included) The following illustration shows the C2N-CBD-P with two double-row button caps and two rows of split small button caps. C2N-CBD-P Keypad Physical View – C2N-CBD-P-A-S Shown (Shown with Faceplate, not included) Cameo Keypads •... - Page 16 Crestron Engraver software, Version 5.04.003.00 or later, is available from the Crestron Web site (www.crestron.com). 12 • Cameo Keypads...
- Page 17 Crestron C2N-CBD/CBF/CBV Cameo Keypads C2N-CBD Overall Dimensions (Front and Rear Views) (C2N-CBD-P Shown) 3.81 in (97 mm) 2.78 in 4.13 in (71 mm) (105 mm) 3.28 in (84 mm) 0.88 in (23 mm) Cameo Keypads • 13 Operations & Installation Guide - DOC. 7063E...
- Page 18 Cameo Keypads Crestron C2N-CBD/CBF/CBV C2N-CBD Overall Dimensions (Top and Side Views) (C2N-CBD-P Shown) 1.19 in 1.75 in (31 mm) (45 mm) 2.79 in (71 mm) 0.81 in (21 mm) 14 • Cameo Keypads Operations & Installation Guide - DOC. 7063E...
- Page 19 Crestron C2N-CBD/CBF/CBV Cameo Keypads C2N-CBF-P Overall Dimensions (Front and Rear Views) 2.74 in 3.21 in (70 mm) (82 mm) 1.76 in (45 mm) C2N-CBF-P Overall Dimensions (Top and Side Views) 1.18 in 1.39 in (30 mm) (36 mm) 2.80 in (72 mm) 0.99 in...
- Page 20 Cameo Keypads Crestron C2N-CBD/CBF/CBV C2N-CBV-P Overall Dimensions (Top, Front and Side Views) 16 • Cameo Keypads Operations & Installation Guide - DOC. 7063E...
- Page 21 Crestron C2N-CBD/CBF/CBV Cameo Keypads Connectors, Controls, and Indicators CONNECTORS DESCRIPTION CONTROLS, AND INDICATORS LED Indicators Feedback - (6) LEDs for each of the button positions; Programmable, auto-dimmable adjustable intensity, 10 blinking patterns Bar Graph - (1) 6-segment bar graph display utilizing the six...
- Page 22 Contact Closure Input 1. Interface connectors for the NET and INPUT ports are provided with the unit. 2. Feedback LEDs are green on the C2N-CBD-E, and white on the C2N-CBD-P, C2N-CBD-P-KP, C2N-CBF-P, and C2N-CBV-P. 3. All except C2N-CBD-E. 4. Button caps are backlit on all except C2N-CBD-E.
-
Page 23: Setup
• Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Use the Crestron Power Calculator to help calculate how much power is needed for the system (www.crestron.com/calculators). - Page 24 NOTE: Verify that there is sufficient Cresnet power to support all Cresnet devices. Standard Mounting Installation Standard mount Cameo keypads are supplied partially assembled along with several items as listed in the following table. Supplied Hardware for the C2N-CBD-E, C2N-CBD-P, and C2N-CBD-P-KP DESCRIPTION Bezel Bezel assembly...
- Page 25 Crestron C2N-CBD/CBF/CBV Cameo Keypads NOTE: The C2N-CBD-P-KP comes pre-assembled with either On and Off buttons or SCENE 1–4, up, down, and Off buttons. The devices do not come with extra button caps. Assemble the keypad as described in the following steps. Refer to the accompanying illustration.
- Page 26 Cameo Keypads Crestron C2N-CBD/CBF/CBV After the Cresnet network wiring has been installed and verified, use the following procedure to install the keypad in a standard 1-gang electrical box. 1. Turn Cresnet system power off. 2. Using the supplied 4-pin connector, connect the Cresnet cable to the NET port of the keypad 3.
- Page 27 Crestron C2N-CBD/CBF/CBV Cameo Keypads Mounting the Keypad Screws (2) #6-32 x 3/4” 5. Attach the desired decorator style faceplate (not supplied). 6. Turn Cresnet system power on. Cameo Keypads • 23 Operations & Installation Guide - DOC. 7063E...
- Page 28 Cameo Keypads Crestron C2N-CBD/CBF/CBV Flush Mounting Installation The flush mount Cameo keypad is supplied partially assembled along with several items as listed in the following table. Supplied Hardware for the C2N-CBF-P DESCRIPTION Bezel Bezel assembly 4-pin female mini Used to connect Cresnet...
- Page 29 Crestron C2N-CBD/CBF/CBV Cameo Keypads Assembling the Keypad (C2N-CBF Shown) Light Sensor LEDs Holes Screws (2) #2-28 x 3/16” Bezel 3. Install and tighten the two supplied #2-28 x 3/16” screws. 4. Press each button and release to ensure that the button caps move freely.
- Page 30 Cameo Keypads Crestron C2N-CBD/CBF/CBV After the Cresnet network wiring has been installed and verified, use the following procedure to install the keypad in the prepared hole. 1. Turn Cresnet system power off. 2. Connect the Cresnet cable to the keypad’s NET port using the supplied mating connector.
- Page 31 Crestron C2N-CBD/CBF/CBV Cameo Keypads Vimar Style Electrical Box Mounting Installation The Vimar mount Cameo keypad is supplied partially assembled along with several items as listed in the following table. Supplied Hardware for the C2N-CBV-P DESCRIPTION Vimar Style Bezel Bezel assembly...
- Page 32 Cameo Keypads Crestron C2N-CBD/CBF/CBV Assembling the Keypad (C2N-CBV Shown) 4. Press each button and release to ensure that the button caps move freely. After the Cresnet network wiring has been installed and verified, use the following procedure to install the keypad in Vimar style electrical box.
- Page 33 Crestron C2N-CBD/CBF/CBV Cameo Keypads Mounting the Keypad 5. Turn Cresnet system power on. Cameo Keypads • 29 Operations & Installation Guide - DOC. 7063E...
-
Page 34: Uploading And Upgrading
(such as changing the device ID) to ensure proper functioning. NOTE: Crestron software and any files on the Web site are for Authorized Crestron dealers and Crestron Service Providers (CSPs) only. New users may be required to register to obtain access to certain areas of the site (including the FTP site). -
Page 35: Programs And Firmware
Crestron Studio help file, the SIMPL Windows help file, or the Crestron Toolbox help file. Crestron If a Crestron Studio (or SIMPL Windows) program is provided, it can be Studio / uploaded to the control system using Crestron Studio (or SIMPL SIMPL Windows) or Crestron Toolbox. -
Page 36: Ambient Light Sensor Operation
To do this, there are signals available on the programming symbol to allow one unit to act as the master backlight controller, and the rest as slaves. Refer to the Crestron Studio or SIMPL Windows help file for more information. 32 • Cameo Keypads... -
Page 37: Problem Solving
Crestron C2N-CBD/CBF/CBV Cameo Keypads Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. C2N-CBD/CBF/CBV Troubleshooting TROUBLE POSSIBLE CORRECTIVE CAUSE(S) ACTION The keypad does The wrong power Use a Crestron power not function. -
Page 38: Check Network Wiring
For example, a Cresnet run using 18 AWG Crestron Certified Wire and drawing 20 watts should not have a length of run more than 333 feet (101 meters). If Cresnet HP is used for the same run, its length could extend to 1250 feet (381 meters). -
Page 39: Reference Documents
[1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of Crestron worldwide offices at (www.crestron.com/offices. To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp. First-time users must establish a user account to fully benefit from all available features. -
Page 40: Appendix: Template For Flush Mount Hole
Cameo Keypads Crestron C2N-CBD/CBF/CBV Appendix: Template for Flush Mount Hole The figure on the following page (not to scale) illustrates the supplied template used to prepare the hole in the wall or other mounting surface for the flush mount Cameo keypad. - Page 41 Crestron C2N-CBD/CBF/CBV Cameo Keypads Cutout Template (Not to Scale) TEMPLATE - OV40096 FOR C2N-CBF THIS PIECE IS FOR CENTER LINE REFERENCE ONLY. DO NOT USE THIS PIECE AS A CUTTING TEMPLATE 5 3/8 in (137 mm) 3 1/4 in (83 mm)
-
Page 42: Return And Warranty Policies
(property or economic damages inclusive) arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or made by the purchaser for a third party. - Page 43 Crestron C2N-CBD/C2N-CBF Series Cameo Keypads This page is intentionally left blank. This page is intentionally left blank. Cameo Keypads • 39 Operations & Installation Guide - DOC. 7063E...
- Page 44 Crestron Electronics, Inc. Operations & Installation Guide – DOC. 7063E 15 Volvo Drive Rockleigh, NJ 07647 (2028549) Tel: 888.CRESTRON 07.13 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.